Best Master Magnetics Flexible Industrial Magnets in 2026

Product 1: Color : White

Product 1: Item model number : ‎ 08505

Product 1: Country of Origin ‏ : ‎ USA

Magnet holds on one side only and is rated at up to 19-1/2 pounds perpendicular pull per linear foot, about 40% less pounds pull on vertical surface against sliding force, and less on painted steel

Magnet designed to hold on contact with flat, smooth ferrous steel, without a layer of material between magnet and steel not to other magnets

Indoor/outdoor adhesive is pressure-activated, permanent, acrylic type, covered by peel-off liner with initial tack and minimum of 24 hour setting time requirement

This product is not liquid, therefore the weight cannot be measured in fluid ounces. It weighs 2.2 pounds. I'm not able to update that myself.

The length is 100 feet. I cannot update that myself.

The width is 1/4 of an inch

Flexible magnets are 30 Mil thick about the same thickness as 8 pieces of stacked copy paper and are laminated with a sticky, rubber based, pressure-activated adhesive suitable for indoor applications

Designed to hold 1 paper business card to flat, smooth ferrous steel, without a layer of material between magnet and steel not to other magnets

Contains 100 each pre-cut, 2" x 3-1/2" size magnets with a tolerance of +/- 1/16" on both dimensions

Magnet holds on one side only and is rated at up to 9 pounds perpendicular pull per linear foot, about 40% less pounds pull on vertical surface against sliding force, and less on painted steel

Magnet designed to hold on contact with flat, smooth ferrous steel, without a layer of material between magnet and steel not to other magnets. Minimum recommended length for magnet is 1-1/3"

Indoor/outdoor adhesive is pressure-activated, permanent, acrylic type, covered by peel-off liner with initial tack and minimum of 24 hour setting time requirement

Flexible magnet strip is magnetic on one side, attaches to flat or slightly curved steel surfaces, and is easily repositioned

Small groove identifies the non-magnetic side

Strength rating is 9 pounds of pull per linear foot

Magnet holds on one side only and is rated at up to 9 pounds perpendicular pull per linear foot, about 40% less pounds pull on vertical surface against sliding force, and less on painted steel

Magnet designed to hold on contact with flat, smooth ferrous steel, without a layer of material between magnet and steel not to other magnets. Minimum recommended length for magnet is 1-1/3"

Indoor/outdoor adhesive is pressure-activated, permanent, acrylic type, covered by peel-off liner with initial tack and minimum of 24 hour setting time requirement

Flexible magnet strip is magnetic on one side, attaches to flat or slightly curved steel surfaces, and is easily repositioned

Small groove identifies the non-magnetic side

Strength rating is 12 pounds of pull per linear foot

Designed to attract, hold, and release bulk steel pieces

Release by lifting "T" handle with fingertips

Magnet assembly weighs 11 pounds

Score-cut every 2" on roll, cut almost completely through so that each piece is removed easily & cleanly. Tolerance on length is +/- 1/16"

Magnet holds on one side only and is rated at up to 1 pound perpendicular pull per 1/2" x 2" piece, or about 40% less pounds pull on vertical surface against sliding force, and less on painted steel

Magnet designed to hold on contact with flat, smooth ferrous steel, without a layer of material between magnet and steel not to other magnets. Minimum recommended length for magnet is 2"

Magnet holds on one side only and is rated at up to 4 pounds perpendicular pull per linear foot, about 40% less pounds pull on vertical surface against sliding force, and less on painted steel

Magnet designed to hold on contact with flat, smooth ferrous steel, without a layer of material between magnet and steel not to other magnets. Minimum recommended length for magnet is 3"

Indoor/outdoor adhesive is pressure-activated, permanent, acrylic type, covered by peel-off liner with initial tack and minimum of 24 hour setting time requirement

Magnet holds on one side only and is rated at up to 39 pounds perpendicular pull per linear foot, about 40% less pounds pull on vertical surface against sliding force, and less on painted steel

Magnet designed to hold on contact with flat, smooth ferrous steel, without a layer of material between magnet and steel not to other magnets

Indoor/outdoor adhesive is pressure-activated, permanent, acrylic type, covered by peel-off liner with initial tack and minimum of 24 hour cure time requirement

Magnet holds on one side only and is rated at up to 13 pounds perpendicular pull per linear foot, about 40% less pounds pull on vertical surface against sliding force, and less on painted steel

Magnet designed to hold on contact with flat, smooth ferrous steel, without a layer of material between magnet and steel not to other magnets. Minimum recommended length for magnet is 1"

Indoor/outdoor adhesive is pressure-activated, permanent, acrylic type, covered by peel-off liner with initial tack and minimum of 24 hour setting time requirement

Magnet holds on one side only and is rated at up to 6 pounds perpendicular pull per linear foot, about 40% less pounds pull on vertical surface against sliding force, and less on painted steel

Magnet designed to hold on contact with flat, smooth ferrous steel, without a layer of material between magnet and steel not to other magnets. Minimum recommended length for magnet is 2"

Indoor/outdoor adhesive is pressure-activated, permanent, acrylic type, covered by peel-off liner with initial tack and minimum of 24 hour cure time requirement