Best Dock Hardware Brackets in 2026

2 - Heavy Duty Side Leg Holders 5" x 5" x 1/8"

4 - Back Plates: 5" x 5" x 1/8"

Kit has 7/16" holes, Mounting: 3/8" x 2-1/2" (not included)

Additional mounting hardware so your dock or pontoon ladders so you can use in more than one location

Fits RecPro Marine AL-A3, A4, A5 Pontoon and Dock Ladders

Fits RecPro Marine AL-C4 Folding Pontoon Ladders

Made in Canada

Package height :25.908 cm

Package length :13.97 cm

If you lost your Payload or Loading Dock hardware then this is what you're looking for

2x P-clamps

4x nylon nuts

【FOR 1-3/8" OD PIPE】End rail T clamp suits for connecting 1-3/8" OUTER DIAMETER pipe to another 1-3/8" OUTER DIAMETER pipe.

【HOT-DIP GALVANIZED】With strong hardness, high corrosion resistance. Chain link fence end T clamps are not easy to rust and have a long life span. Have great performance in outdoor environments.

【BOLTS & NUTS INCLUDED】Package contains end rail clamps 6 pack. No need to buy bolts and nuts separately, one package can meet all of your use needs.

Connector Big-T

Size: 5" x 5" x 1/4"

Industrial, heavy duty gauge

3/4" Diameter - Galvanized Steel

3" Pin with Hitch Clip.

Robust Design

1/4" Hot dip galvanized steel

Slot Size 9/16"

3/8" Tab for 3/4" Pin

1/4" Thick 5" x 5" Backer Plates with 3/4" ears (on DH-TM) and 1/2" ears (on DH-TF)

Contains 2 Backer Plates and connector pin with hitch clip

Includes 8 - 1/2" x 3" Carriage Bolts, Nuts & washers for use with 2x lumber

1/4" Galvanized Steel

Robust Design

Made in the USA

1/4" Galvanized Steel

Robust Design

Made in the USA

1/4" Galvanized Steel with 3/4" thick ear

Robust Design

9/16" square holes and 3.5" between centers

1/4" Hot Dipped Galvanized Steel with 1/2" Ears

Robust Design

9/16" square holes and 3.5" between centers

This pipe holder features a 3.5" outside diameter and a 3" inside diameter.

Welded onto a heavy duty 5" x 5" backer plate.

Manufactured using 1/4" galvanized steel hardware that is built to last.

1/4" Galvanized Steel

9/16" Square Holes

Robust Design

3/8" or 1/2" S. S. assembly bolts, nuts, and washers available for Pipe Leg Docks

Additional stainless steel hardware is available

solid cast aluminum

3/8" or 1/2" S. S. assembly bolts, nuts, and washers available for Pipe Leg Docks

Additional stainless steel hardware is available

solid cast aluminum

Use when connecting a T-section or an L-section at the end of your dock, reinforcing a dock corner, or in the construction of a new dock section

Heavy-duty 3.2 mm steel construction provides exceptional strength in any configuration

Galvanized finish protects against rust and other damage in freshwater marine environments

Includes (2) 2" Pipe Holders.

This pipe holder features a 2.5" outside diameter and a 2" inside diameter.

Welded onto a heavy duty 5" x 5" backer plate.

1/4" Galvanized Steel

9/16" Square Holes

Slotted 9/16″ holes for use with a variety of cleat sizes

Kit allows you to add a joist to your dock frame for additional strength and rigidity.

Works seamlessly with the Dock Hardware "Dock in a Box" kit to add length to your dock.

Includes (2) Dock Angles, (4) Washer Plates, and (8) 1/2" x 3" Galvanized Carriage Bolt Sets.

Add two additional legs to your dock - Fits round dock legs up to 1-7/8" diameter

Post brackets use two mounting brackets, one on each side of the dock's faceboard, for a solid connection to the dock

Heavy-duty steel construction provides exceptional strength, while the galvanized finish protects against rust and other damage in freshwater marine environments

Heavy-duty dock construction hardware for the do-it-yourselfer!

Galvanized finish protects against rust and wear and tear in a freshwater environment

Contains (2) large heavy-duty 90° inside corner dock plates, (2) large heavy-duty 90° outside corner dock plates, (6) small backer plates, (3) small 90° corner brackets, (28) M12 carriage bolts, (28) M12 flat washers, and (28) hex nuts

DIMENSIONS: 6.5 inch depth, 48 inch width, 96 inch height, 24 foot length

ALL IN ONE: Includes three 4 ft x 8 ft cedar dock frame kits, two 4 ft dock pipes, two 6 ft dock pipes, two 8 ft dock pipes, two outside corner dock brackets, four straight dock brackets, six dock pipe footpads, six dock pipe safety caps

HEAVY DUTY: Constructed out of high-quality cedar and corrosion resistant hardware; Bracket hardware conveniently located inside pipe sleeve - remove the plastic orange cap to access

DIMENSIONS: 6.5 inch depth, 144 inch width, 96 inch height, 24 foot length

ALL IN ONE: Includes five 4 ft x 8 ft cedar dock frame kits, two 4 ft dock pipes, four 6 ft dock pipes, four 8 ft dock pipes, four outside corner dock brackets, four straight dock brackets, two 3-way inside corner brackets, ten dock pipe foot pads, ten dock pipe safety caps

HEAVY DUTY: Constructed out of high-quality cedar and corrosion resistant hardware; Bracket hardware conveniently located inside pipe sleeve - remove the plastic orange cap to access

DIMENSIONS: 5 inch depth, 10 inch width, 6 inch height, 5 inch product length; Can be used with any 2 inch nominal thickness lumber

PREMIUM QUALITY: Gray polyester powder coat paint for superior rust protection

HEAVY DUTY: High grade zinc-plated mounting hardware for corrosion resistance year after year

DIMENSIONS: 6.5 inch depth, 120 inch width, 72 inch height, 16 foot length

ALL IN ONE: Includes three 4 ft x 8 ft cedar dock frame kits, two 4 ft dock pipes, five 6 ft dock pipes, three outside corner dock brackets, three straight dock brackets, one inside corner bracket, seven dock pipe foot pads, seven dock pipe safety caps

HEAVY DUTY: Constructed out of high-quality cedar and corrosion resistant hardware; Bracket hardware conveniently located inside pipe sleeve - remove the plastic orange cap to access