Best Oatey Transmission Tools in 2026

J-36418-C Turbine Shaft Teflon Seal Installer/Resizer – For GM 700-R4, 4L60, 4L60-E, 4L65E, 4L70L 1982 - UP transmissions.

1503 Stator Shaft Teflon Seal Installer/Resizer – Used on GM 700-R4, 4L60, 4L60-E, 4L65E and 4L70E transmissions.

Great Function – This tool kit will effectively protect the Stator or Turbine Shaft Teflon seals from damage, tear and distortion during installation.

Wide Application – For use on universal transmissions and will fit most common clutch drums up to 6" in size. To check more applicable models, please refer to the description below.

Great Function – Removing the snap ring on a transmission clutch may be tricky. The tool is designed to relieve the pressure off the snap ring by compressing the return spring, allowing easy removal and installation of the snap spring. It will be very helpful for your work. (Attention: Does not do rear case pistons)

Considerate Design – 6" long legs especially designed for deep drums. Similar to Atec Trans-Tool T-0158-HD. Mounts to work bench or table or on a bench vise.

【Perfect Fitment】Compatible with BMW N20 N26 engines. Fits for BMW 1 Series 2012-2016; Fits for BMW 2 Series 2014-2016; Fits for BMW 3 Series 2012-2016; Fits for BMW 4 Series 2014-2016; Fits for BMW X1 2011-2015; Fits for BMW X3 2011-2017; Fits for BMW X4 2014-2017; Fits for BMW Z4 2011-2017. Direct replacement for BMW factory tool part number 83 30 2 318 117, 83 30 2 212 825 and 83302222742 (Attention: Automatic transmissions only.)

【2801 Flywheel Holder Tool】Used to easily and properly lock the transmission flex plate in place to perform a timing service for N20 N26 engines. Also can secure the crankshaft with the transmission installed (connect to engine). In additional, can better hold the flywheel / flex plate while replacing the timing chain, allows you release and tighten down the central bolt on the vibration damper hub.

【7676 Oil Seal Repair Kit】Specially designed to easily remove, install and replace the oil pump, chain, balance shaft housing and sprocket during chain repairs, helps you align the balancer shaft into the correct timed position and holding chain sprocket.

Practical Function – Used to quickly remove conventional type pumps without damage.

Wide Application – Fits for GM 200, 200C, 200-4R, 250, 250-C, 350, 350-C, 375, 400 ( 3L80 ), 425, 475 ( 3L80-HD ), 700-R4 (4L60) (4L60E), Powerglide | For Ford C4, C5, C6, AOD, AODE, AOD-EW (4R70W), E40D | For 404 (30TH), 413, 470 (31TH), 727 (36RH) (37RH), 904 (30RH), 998 (31RH), 999 (32RH).

Direct Replacement – Alternative to Atec Trans-Tool T-0033 and Kent-Moore J-45053 both in function and performance.

【Application】Fits for 4L60E 4LC65E 4L70E 4L80E; Fits for GM Chevy Cars and Trucks with V6 and V8 transmissions 1996 and newer; Fits for Impala C1500 C2500 C3500 K1500 CT4/5/6 Camaro etc.

【Must Have Tool】Special tools must be used to remove the leaking seal around the shifter selector shaft mechanism through the transmission case.

【High Performance】This handy tools set will help you easily & properly remove and insert the seal without removing the tranny pan or in most cases without even lowering the transmission.

【Application】Compatible with THM700-R4 (MD8), 4L60, 4L60E, 4L70E gearboxes. The shaft seal installer allows easily install and adjust the turbine shaft seals for 4L80E and 4L85E. The re-sizer is used to size the pump bushing for 700r4 4l60e and align the pump rotor, avoiding install improperly and damage the seals.

【High Performance】The turbine shaft transmission tools are designed to helps install the turbine shaft seals into proper grooves and determine the size or compress each seal into the groove. The pump bushing rotor sizer is that a tool to size your pump bushing, and align your pump rotor, test for play and movement.

【Powerful Features】The turbine shaft seal installers are small and easy to carry. It only takes up very little storage space. You can put them in your pocket when you go out if necessary.