Best Gama Electronics in 2026

Ideal for car, truck, boat or RV battery

Convenience: knob type, easy to install & simple to use. Loose / twist of the knob, then power will cut.

Heavy Duty: solid brass made, rust and corrosion resistant, durable made for safety use.

Waterproof to IP65

Rated 16 amp 125 VAC, 10 amp 250 VAC, 10 amp 12VDC

SPST Off-On

Set of 2 Mugs - one Blue & one Red

Insulated

BPA Free

Insulated

Microwave/Dishwasher safe

Made in the USA

Insulated

Microwave/Dishwasher safe

Made in the USA

Insulated

Microwave/Dishwasher safe

Made in the USA

Insulated

Microwave/Dishwasher safe

Made in the USA

Insulated

Microwave/Dishwasher safe

Made in the USA

Simple twist of a knob provides a convenient way to quickly disconnect and reconnect power from an automotive battery.

Clean, solid, low profile connection to GM side post batteries.

Simple to disconnect your battery to work on your vehicle or the knob can be removed to prevent theft.

For use with 12, 24 and 32 Volt Marine Electrical Systems

Capacity - 250 AMPS Continuous, 360 AMPS Intermittent

Ignition Protected

Selector 4 Position. Switches isolated battery banks to all loads or combines battery banks to all loads

Ignition protected—safe for installation aboard gasoline powered boats

IP66 waterproof, ISO 8846 and meets ABYC requirements

60A

Water Proof

Splash & Dust Proof

Permits selection between batteries for starting, charging or operation in parallel

For use with two or more batteries and systems under 50V

UL listed, ignition protected and CE approved

Blue Sea Systems Battery Switch m-Series ON/OFF with Knob, part number 6006, is a Single Circuit ON-OFF switch. Switches a single battery to a single load group

IP66 waterproof, ISO 8846 and meets ABYC requirements. Ignition protected—safe for installation aboard gasoline powered boats

Make before break contact design allows switching between battery banks without power interruption

🔋【Material】: Heavy duty battery shut off switch made of ABS plastic housing, and the 4 sets of bolts is tinned copper studs(2 x 3/8" (10mm) & nuts for ignition protected to distinguish the different gears easily which you switch to even at night.

🔋【Easy Operation】: RV Battery switch with On/Off position in clear color labels. Switch ON=Power (green) to closed circuit, Switch OFF = No power (red) to the cut-off circuit.

🔋【Compatible 】: Used for 12-48V, 275 A continuous at DC 12V, 455 A intermittent at DC 12V, 1250 A momentary at DC 12V, battery selector switch can stand alone or be locked together with other switch for minimizing battery loss and preventing electric leakage effectively.

Easy to Use Kit for a Professional Installation

High Current (180A Continuous/1000A Intermittent) Battery Disconnect Switch with Black On/Off Plate

Contains #2 3/8" Copper Lugs, Heavy Duty Heat Shrink, and Rubber Terminal Insulators

Rated to 180A Continuous or 1000A Intermittent

Mounts in 3/4" Hole

Provides Single Power Cut off to Entire Electrical System

Polycarbonate body with brass terminals

Dimensions: 5-1/4" diameter x 2-5/8" depth, 5/16" terminal stud size

For use with 6 to 50 volt marine electrical systems

Switches a single battery to a single load group Ignition protected - safe for installation aboard gasoline powered boats

IP66 waterproof, ISO 8846 and meets ABYC requirements

Accepts two 4/0 AWG (95mm²) battery cables.

Simple Operation:Switch on = Power; Switch off = No power.Rating: 275A DC Continuous (1hr), 455A DC Intermittent (5 min), 1250A DC Cranking (10 sec); Stud Size: 2x3/8" (10mm)

Durable Material: This battery disconnect switch is made of ABS plastic housing, tinned copper studs and nuts.Come with 4 stainless steel mounting screws and caps to help fix the switch tightly. 4 Removable side plates provide access for battery cables

Safety Protection:battery shut off switch can disconnects the battery safely, protect batteries from excessive drain when vehicle or boat is not in use

Rotary Switch

Panel Mount

125 amp 12V

Battery Holder Type: 9v battery holder with switch, 9v battery holder with on off switch

Battery Holder Voltage Output: 9V, 1 x 9v battery holder= 9 volt battery holder with leads; Battery Holder Switch Function: ON/OFF switch on 9 volt battery case holder

9 Volt Battery Holder Dimensions: (L*W*H)/2.657" x 1.299" x 0.835"/6.75cm x 3.30cm x 2.12cm

Heavy Duty: ABS plastic housing, durable made for safety use, rear cover insulates terminals against any short of circuits, equiped with 4 sets of bolts.

Operation: On/Off 2 positions, 275 A continuous at DC 12V, 455 A intermittent at DC 12V, 1250 A momentary at DC 12V.

Compatible: used for DC 12 - 48 V systems to isolate and secure the electrical system, can stand alone or be locked together with other switch.

Heavy Duty: ABS plastic housing, durable made for safety use, rear cover insulates terminals against any short of circuits, equipped with 4 sets of bolts.

Operation: On/Off 2 positions, 275 A continuous at DC 12V, 455 A intermittent at DC 12V, 1250 A momentary at DC 12V.

Compatible: used for DC 12 - 48V systems to isolate and secure the electrical system, can stand alone or be locked together with other switch.Its purpose is to eliminate any power draw from the battery when vehicle or boat is not in use, disconnects the battery safely.

Push button switch with highly visible red button is suitable for any momentary function

Positions: Off – Momentary On

Requires ½ inch mounting hole

Heavy Duty: ABS plastic housing, durable made for safety use, rear cover insulates terminals against any short of circuits. Design for 2 batteries vehicles, can switch battery 1 / battery 2 separately or both on and off.

Purpose: eliminate any power from the battery when vehicle or boat is not in use, disconnects the battery safely.Avoid battery drain off.

Operation: 1-2-Both-Off,4 positions, 200A continuous at 12VDC, 300A intermittent at 12VDC, 1000A momentary at 12VDC.

Branch circuit breakers (can also be used for 24-hour circuit protection)

Compact design enables high density circuit protection configurations

Push-to-reset operation

Universal battery isolator switch: this battery kill switch is universal applied for RV, marine, car, boat, travel trailer, truck, ATV, UTV battery and other 12 - 60 volt devices, which makes it an effortless job for turning the battery on and off

Simple operation: this RV battery disconnect switch is easy to install; With ON/ OFF 2 positions in clear color labels, ON (green) represents the closed circuit and OFF (red) represents the cut-off circuit

Heavy duty isolator switch: this battery master switch is made of reliable ABS plastic housing; The rear cover insulates terminals against any short of circuits; Each battery shut off switch comes with 4 stainless steel mounting screws and caps to help fix the switch tightly; 4 Removable side plates provide access for battery cables