Best Hobbypower in 2026

Regardless the throttle stick position, the motor will not spin after battery connected.

Throttle Calibration: Throttle range can be configured to provide best throttle linearity, fully compatible with all market available transmitters.

Brake Setting: brake enabled / brake disabled.

Max Efficiency: 80%

Max Efficiency Current: 4-10A (>75%)

Motor Dimensions: Φ27.5 x 30mm

Operating Voltage: 3-5V

Speed: 31,500 RPM with 3V Voltage; 53,000 RPM with 5V Voltage

Motor Diameter: 8..5mm; Motor Length: 20mm

Sport - Harder, Long-Wear rubber compound

Pre-Glued

Molded tires are known for near perfect balance

Rear-wheel drive (RWD)1:10 drift kit

very suitable for drifting beginners.

The kit weight centered at the back and it already comes with the ultra wide angle steering system making the beginner easier to handle and enjoy the drifting experience.

30A SimonK firmware Brushless ESC

Soldered with 3pcs 3.5mm gold female plug, very convenient to connect motor.

Highest accuracy with Crystal Oscillator (Temperature won't affect the PWM operating range like other cheap ESC's).

Pack of 4,(1.5mm 2.0mm 2.5mm 3.0mm)*1

Total length: 195mm Diameter of handle: 18mm Length of handle: 90mm

Everything you need to repair your favourite toys!

Specifically designed for DJI phantom series and Walkera QR X350 series Quadcopter.

Made of 3K Carbon fiber

Works good to eliminate high frequency vibration and low frequency vibration.

Parts No: R025 + R020

Suitable for HSP, HIMOTO, REDCAT & TYRANNO with CXP 18, VX 16 18 and SH 21 Nitro Engines.

For 12mm Across Flat One Way Bearing, with 6mm shaft diameter.

Wheelbase: 500mm

Motor suggest: 2212 - 2216 size brushless motor

Prop suggest: 10"-12"

Use for multi-rotor such as Tri, Quad, Hexa, and Octo...etc.

Designed for Multi-rotor fast transient

2 x Emax MT2213-935KV CW Brushless Motor

1/10 4WD Drift Racing Car Frame Kit for D3,come with the front one way differential for free

Black carbon fiber chassis

The three belt for four wheel drive (4WD)

This adapter can convert BCM94360CS2/BCM943224PCIEBT2 card to NGFF(M.2) Key A/E interface for Mac OS and Hackintosh

This adapter does not contain BCM94360CS2/BCM943224PCIEBT2 card

This adapter is not suitable for notebook/laptop due to height bottleneck limit, it is suitable for desktop motherboard with NGFF(M.2) key A/E connector , such as, Asus ,MSI and GIGABYTE Z170 ITX series motherboard

For 25mm diameter tube

Dimension: approx. 37 x 31 x 5 mm

3-Axis Aircraft: need 12 pcs

Dimensions: 4" length

Servo Extendtion wire (Male to Male)

Length:100mm

Brand new and High quality

Size : 26AWG,600mm

Futaba male to female plug

HSP Upgrade Steel Diff. Gear set( 39T & 44T) for 1/10 HSP 94122 94102 Nitro car

Use this steel gear to replace the stock plastic gear, upgrade you car. the steel gear will be more durable, and effectively avoid jamming gear when racing.

Install suggestion: take off the speed transmission kit direct, and replace the gear, do not take off the engine.

Tire OD: 67mm , ID: 45mm

Hexagon coupling: 12mm

Tires wide: 27mm

This bracket is use to mount the smart phone as monitor for DJI Phantom FPV.

Suitable for all smart phone ( iPhone, Samsung, HTC...etc.)

Only the bracket is included in this auction.

Fits for RC 1: 10 on-road Racing car, drift, touring car...etc

Material: Tyre:Soft Rubber

Material: Wheels:Plastic

Parts No:70111

Parts Name: Engine Amax Himoto Exceed

Starter drill holder:11011

The design allows the motor to be positioned in the rear of the car, making the weight more focus at the back and with the ultra wide angle steering system; bringing the drifting to another level.

it's a almost assembled finished version, you just need install battery and electronic accessories for run.

Attention: only a kit, without any electronic device.

24 leds Chassis Light set

Used for RC 1/10 1/8 Cars

Input voltage 6V, can be powered from receiver directly.

3-cell Lithium Polymer Battery

Pack Configuration: 3S1P

Capacity: 2200mAh

This action is a DIY F550 Hexacopter kit, it is unassembled.

Come with high quality electronic accessories, only need a 3S Lipo battery and a 6CH system to complete.

This F550 quadcopter is a very popular machine, it has a strong rack.This F550 quadcopter is a very popular machine, it has a strong rack, beautiful appearance, and a stable system for smooth flight, it is very good for fly and FPV

For DJI Phantom 4 quadcopter

Protects the camera and gimbal from crash damage

Buckle design, easy installation and removal

This is the new APM 2.8 autopilot module. The sensors are exactly the same as with APM2.6, however this version does not have an onboard compass, which makes this version ideal for use with multicopters and rovers.

The APM 2.8 is a complete open source autopilot system and the bestselling technology that won the prestigious 2012 Outback Challenge UAV competition. It allows the user to turn any fixed, rotary wing or multirotor vehicle (even cars and boats) into a fully autonomous vehicle; capable of performing programmed GPS missions with waypoints. Available with top or side connectors.

Includes 3-axis gyro, accelerometer and magnetometer, along with a high-performance barometer

pull starter for VX 16-21 Nitro Engines of 1/10 RC car

Suitable for HSP, HIMOTO, REDCAT & TYRANNO with CXP 18, VX 16 18 and SH 21 Nitro Engines.

For 12mm Across Flat One Way Bearing, with 6mm shaft diameter.

Designed for Futaba /JR / Radiolink / Walkrea / Flysky / Esky / WFLY ect.transmitter

the Neck strap Balancer: connection mouth wide 3mm

Material:Aluminum alloy

Advanced 32 bit CortexM4 ARM high performance processor, can run RTOS NuttX real time operating system

Bus interface (UART, I2C, SPI, CAN)

Integrated backup power supply and failure backup controller, the main controller can be safely switched to backup control