Best Xcfdp in 2026

【BASIC PARAMETERS】This single phase vfd drive: 1 phase input and 3 phase output;Input voltage: 220V(+/-15%),Output voltage: 220V; Input frequency: 50/60 Hz,Output frequency: 0-400 Hz; The power is 2.2KW 3HP 12A, AC 220V; VFD Dimension: 4.61 x 4.96 x 6.89 inches (L x W x H).NOTE:Some products do not have the "XCFDP" brand logo on the product due to the production batch, and there is no difference in other parameters, please don't mind this.

【EXCELLENT PERFORMANCE】With the copper coil of good quality,this Vfd drive is safer and more durable.And this vfd adopts the multi-grid design with enough cooling space between the electronic components and the case, so it is easier to cool quickly.

【MULTI-PROTECTION AND EASY TO OPERATE】this vfd drive is screwed tightly and equipped with multiple protection functions for stable and safe operation,such as Three Anti-Paint Protection Lines,Over Current Protection,Over Voltage Protection,Overload Protection,Short Circuit Protection.And the simple removable control panel and the easy connection make this vfd easier to use.(!!NOTE:Comes with 20cm control panel cable inside the vfd, extra extension cables are not included.)

Size: About 150 * 0.5 * 0.2cm/59 * 0.2 * 0.09inch(L*W*H);

Made of high quality material, it is durable and long lasting use.

It is compatible with many stepper models.

Potentiometer cable（about 15CM） can be separated, with running stop brake function

Suitable for long hours of work:Circuit optimization design,stable

Adjust the motor smooth no noise no vibration,with power indication,wide duty cycle adjustment range

Input supply voltage: 1.8V-15VDC;

The maximum output power: 30W

The maximum continuous output current :2A

L298N main driving chip, high drive ability, small heating value, strong anti-interference capability.

Dual H bridge DC stepper module, more stable and higher work efficiency.

Size: 43 * 43 * 27 mm/1.69 * 1.49 * 1.06in

The input power range is dc6-28v; the maximum continuous output current: 3a; the maximum output power: 80W

The switch cable length 15cm/5.9in

Potentiometer with switch function

Pushbutton Control

44.5mm wide

Manufacturer: Schneider Electric (Telemecanique)

Voltage: 24V;

Frequency: 50/60Hz;

Electrical Connections: 6" Leads;

Small Size, Short Height

16Ncm(22.6oz.in) holding torque

NEMA 17 bipolar 1.65x1.65x0.79 4-wire

Reversing relay module. Powers any reversing motor equipment, can be used for any application that requires the ability to reverse motion

Support Momentary-action(Self-resetting) switch and Alternate-action (Self-holding) switch. For Self-resetting switch, when the switch is pressed the motor operates, and when the switch is released the motor stops.

Compact plastic case and wires connect for easy mount.

Product Name: Overload Protection Switch; Country of Manufacture: CHINA; Material: Plastic, Metal; Net Weight: 14g

Package Content: 1 x Overload Protection Switch; Brand: Assisi; Model: HS-R01

Main Color: Black, Red; Voltage: AC 125/250V 50/60Hz; Current: 20A

The maximum matching 5-axis stepper motor driver

The two-stage signal processing, signal transmission smooth, powerful anti-jamming

Relay output control interface, can be accessed by the spindle motor or the air pump, water pump, etc

Package included: 1 x Stepper Motor Driver.

✿Stepper Motor Driver✿: 9V-42V DC power supply, H bridge bipolar constant phase flow drive. The maximum 4.0A of the eight kinds of output current.

✿The largest 32 subdivision of the 6 models are optional; Suitable for 4Wires, 6 wires and 8 wires stepper motor. it can control 2 phase stepper motor forward and reverse rotation, With 1-2, W1 -2 , 2W1 -2, 4W1 -2 phase excitation mode.

Suitable for Nema 17, Nema 23 and Nema34 Stepper Motor，2-phase hybrid stepper motors (Outer diameter: 42, 57,86mm).

Package: 1piece DM542

More informations, please refer to the last photo in this link.

【Motor Speed Controller】Ultra-low voltage dc motor governor with the chip model: NE555; Potentiometer with switch function; Use a 2A resettable fuse to protect the controller; Power-on indicator.

【High Performance】Input supply voltage DC 1.8V-15V. Maximum continuous output current 2A. Maximum output power 30W. Duty cycle adjustable 0%-100%.

【Secure Enough】The speed controller is equipped with a self-recovery fuse. When the current is too large, the fuse is automatically disconnected. After cooling, the fuse is automatically restored.

Inside Hole Diameter:10-11mm

Aftermarket Parts

For TTR50 110cc 125cc 140cc 150cc 160cc Dirt Bike Pit Bikes Motocross

The stepping motor is a kind of mechanical and electrical device that converts electrical pulses into angular displacement. Come with a standard interface, when used directly pluggable.

Drive Module Board Size(in): 1.37 * 1.18 * 0.6(in); Stepper Motor diameter: 1.06(in); Stepper Motor lines: 9.45(in).

A, B, C, D four-phase LED indicates the status of the stepper motor work.

5 HP, 220/240V, Single Phase.

Best quality starter with built-in overload adjustable from 22-34 amps.

Manual reset button that can be switched to auto reset.

♕【Technical Parameters】 Input supply voltage: DC 10V-55V; Maximum current: 60A; Continuous current: 40A; Speed range: 0%-100% ; Control frequency: 15KHZ; Apply to: DC Brush Motor

♕【Switch Function】The PWM DC motor speed controller come with switch function. High power speed controller switch which is much more adaptable and convenient to change the motor direction.

♕【Excellent Heat Dissipation Performance】 The enclosure of the speed controller for motor is an aluminum enclosure. Aluminum shell is very strong to prevent damage, holes on its side and top which are helpful for heat dissipation.

Auto Guide Terminal: RJ-12 6pin (ST-4 Type)

Power supply (recommended): 4 x AA alkaline batteries (sold separately)

Size and Weight: 6.8 x 4.5 x 3.8 inches (173.5 x 113.3 x 96 mm), Approx. 2.2 lbs (1

Input voltage: 220V(+/-15%); Output voltage: 220VAC; Input frequency: 50/60 Hz; Output frequency: 0-400 Hz; Input phase: 1 phase; Output phase: 3 phase.

Application: Spindle Motor, Drill Press, CNC, HVAC, Lathe, Milling, Pumps, Conveyors, Mach3, Fan, Cooling, Compressor, Three-phase motor and other machines!

Spacing 2.54mm bar connector, 5-pin plug. DC cooling fan low noise, large air volume.

Auto Guide Terminal: RJ-12 6pin (ST-4 Type)

Power supply (recommended): 4 x AA alkaline batteries (sold separately)

Size and Weight: 6.8 x 4.5 x 3.8 inches (173.5 x 113.3 x 96 mm), Approx. 2.2 lbs (1

Auto Guide Terminal: RJ-12 6pin (ST-4 Type)

Power supply (recommended): 4 x AA alkaline batteries (sold separately)

Size and Weight: 6.8 x 4.5 x 3.8 inches (173.5 x 113.3 x 96 mm), Approx. 2.2 lbs (1

Voltage: AC 110- 220V

Maximum Power: 10000W (connected resistive load,220VAC)

Voltage Regulation: AC 10V to 220VAC

The input voltage must be equal to the rated voltage of the motor.Wide Voltage: Wide voltage input 10-55V, maximum output current 60A,Continuous current: 40A.

Digital display :Motor Rotation Speed Percentage 0~100% ,Accurate adjustment speed.Adjust Output Current Control Motor Speed

Speed Control Knob:Stepless speed regulation ,and with Forward-Brake-Reverse Switch.Only Work for Brushed Motor.

This is single phase VFD with 1 phase INPUT and 3 phase OUTPUT,the power is 2.2KW, 220V,10A, VFD Dimension: 130 x 103 x 200 mm (L x W x H). 🔺🔺Please note: The working environment is relatively humid, with water mist, water droplets or metal objects falling in, which will cause a short circuit.

Input voltage: 220V(+/-15%); Output voltage: 220VAC; Input frequency: 50/60 Hz; Output frequency: 0-400 Hz; Input phase: 1 phase; Output phase: 3 phase.

Application: Spindle Motor, Drill Press, CNC, HVAC, Lathe, Milling, Pumps, Conveyors, Mach3, Fan, Cooling, Compressor, Three-phase motor and other machines!

★【Feature】: This motor speed controller uses screw terminals for convenient and quick wiring. Comes with a momentary start/stop switch and a speed control potentiometer.

★【Stable Function】: This simple and easy-to-use DC motor speed controller has an stable performance. Speed controller is made with high quality circuit board which ensures a longer service life.

★【Design】: Designed with a digital display that shows the rate in percentage of actual speed to maximum speed.

【Maximum Power】 10000W resistance load limit power, room temperature for a long time is recommended to be used within 5000W

【Voltage Regulation】AC 10V to 230V (Adjust begin 20V). The original chip is specially customized SCR, all high-voltage capacitors

【Dimensions】130*60*47mm (5.12"x2.36"x1.85"). Weight: 210g (0.46lb)

Fit For Router Fan Electric Motor Rheostat Variable Speed Controller AC 1500W / 120 volt / 15 amps

For use with brush type motors only, Will not work with brushless type motor or soft/slow start motors,Use with centrifugal fans only

Pls confirm the item if it matches your car before you purchase

Very easy to install

Small size & light weight

Excellent start-up torque