Best Yg-1 in 2026

High-speed steel tools are good for most general purpose applications, offering a combination of hardness and toughness for wear resistance

Black oxide treatment adds lubricity and creates small pockets on the surface of the tool that act to hold coolant near the cutting edge

Round shanks allow use with a wide variety of toolholding systems

High-speed steel tools are good for most general purpose applications, offering a combination of hardness and toughness for wear resistance

Black oxide treatment adds lubricity and creates small pockets on the surface of the tool that act to hold coolant near the cutting edge

Round shanks allow use with a wide variety of toolholding systems

NC spotting drill

90 Degree point angle

Made of 8 percent cobalt and high speed steel

High-speed steel tools are good for most general purpose applications, offering a combination of hardness and toughness for wear resistance

Black oxide treatment adds lubricity and creates small pockets on the surface of the tool that act to hold coolant near the cutting edge

Round shanks allow use with a wide variety of toolholding systems

High-speed steel tools are good for most general purpose applications, offering a combination of hardness and toughness for wear resistance

Titanium nitride coatings add a hard layer of gold-colored ceramic to the surface that extends tool life and permits faster cutting speeds than uncoated tools

Round shanks allow use with a wide variety of toolholding systems

NC spotting drill

120 Degree point angle

Made of 8 percent cobalt and high speed steel

NC spotting drill

90 Degree point angle

Made of 8 percent cobalt and high speed steel

High-speed steel tools are good for most general purpose applications, offering a combination of hardness and toughness for wear resistance

Black oxide treatment adds lubricity and creates small pockets on the surface of the tool that act to hold coolant near the cutting edge

Round shanks allow use with a wide variety of toolholding systems

High-speed steel tools are good for most general purpose applications, offering a combination of hardness and toughness for wear resistance

Uncoated tools feature just the base substrate without any additional treatment or coatings and are suitable for a wide range of applications

Round shanks allow use with a wide variety of toolholding systems

NC spotting drill

120 Degree point angle

Made of 8 percent cobalt and high speed steel

Suitable for general-purpose machining on hardened and high-alloy steel, steel casting, malleable cast iron, chromium-nickel steel, brass, copper, aluminum with a high percentage of silicon, and abrasive plastic

Extra-long-length end mills have longer cutting edges and can make deeper cuts than long-length end mills

Four flutes produce a better finish than fewer flutes

NC spotting drill

120 Degree point angle

Made of 8 percent cobalt and high speed steel

Suitable for machining on hardened and high-alloy steel, steel casting, chill casting, malleable cast iron, chromium-nickel steel, brass, copper, aluminum with a high percentage of silicon, and abrasive plastic

Long-length end mills have longer cutting edges and can make deeper cuts than standard-length end mills

Two flutes offer better chip-carrying capacity than end mills with more flutes, enhancing the tool’s ability to remove material

NC spotting drill

90 Degree point angle

Made of 8 percent cobalt and high speed steel

High-speed steel tools are good for most general purpose applications, offering a combination of hardness and toughness for wear resistance

Titanium nitride coatings add a hard layer of gold-colored ceramic to the surface that extends tool life and permits faster cutting speeds than uncoated tools

Round shanks allow use with a wide variety of toolholding systems

NC spotting drill

120 Degree point angle

Made of 8 percent cobalt and high speed steel

NC spotting drill

90 Degree point angle

Made of 8 percent cobalt and high speed steel

High-speed steel tools are good for most general purpose applications, offering a combination of hardness and toughness for wear resistance

Titanium nitride coatings add a hard layer of gold-colored ceramic to the surface that extends tool life and permits faster cutting speeds than uncoated tools

Round shanks allow use with a wide variety of toolholding systems

High-speed steel tools are good for most general purpose applications, offering a combination of hardness and toughness for wear resistance

Titanium nitride coatings add a hard layer of gold-colored ceramic to the surface that extends tool life and permits faster cutting speeds than uncoated tools

Round shanks allow use with a wide variety of toolholding systems

Secure and convenient tensioning

High quality 16-320mm Hydraulic Crimper

Wire cable crimping tools

NC spotting drill

120 Degree point angle

Made of 8 percent cobalt and high speed steel

NC spotting drill

90 Degree point angle

Made of 8 percent cobalt and high speed steel

High-speed steel tools are good for most general purpose applications, offering a combination of hardness and toughness for wear resistance

Uncoated tools feature just the base substrate without any additional treatment or coatings and are suitable for a wide range of applications

Round shanks allow use with a wide variety of toolholding systems

High-speed steel tools are good for most general purpose applications, offering a combination of hardness and toughness for wear resistance

Uncoated tools feature just the base substrate without any additional treatment or coatings and are suitable for a wide range of applications

Round shanks allow use with a wide variety of toolholding systems

- These taps are made from high speed steel 6542 and surface is coated with titanium for high hardness and rust resistance.

- There are total 9 pieces of taps in different sizes from M2 to M12 that you can use for tapping various threads.

- Taps are designed with spiral flutes is conducive to remove crumbs, not easily broken tap.

Made of high speed steel with high wear and heat resistant, durable and has long service life

Standard metric thread design, clear and tidy, no burr, provide rapid chip removal for efficient threading

These micro taps mainly used for clocks and watches, and low hardness of wood and soft metal hole processing

High-speed steel tools are good for most general purpose applications, offering a combination of hardness and toughness for wear resistance

Uncoated tools feature just the base substrate without any additional treatment or coatings and are suitable for a wide range of applications

Available in round shank with square end

Perfect for cutting and renewing external and internal threads to exact standards. 9 Different Sizes: M2 M2.5 M3 M4 M5 M6 M8 M10 M12

Designed to cut threads for standard-sized screws, clear and tidy, no burr, provide rapid chip removal for efficient threading.

Spiral Tap the crumbs into a spiral up chip evacuation, it is more suitable for the processing of blind holes and not easily broken tap.

High-speed steel tools are good for most general purpose applications, offering a combination of hardness and toughness for wear resistance

Black oxide treatment adds lubricity and creates small pockets on the surface of the tool that act to hold coolant near the cutting edge

Round shanks allow use with a wide variety of toolholding systems

High-speed steel tools are good for most general purpose applications, offering a combination of hardness and toughness for wear resistance

Black oxide treatment adds lubricity and creates small pockets on the surface of the tool that act to hold coolant near the cutting edge

Round shanks allow use with a wide variety of toolholding systems