Best Birthday Cutters in 2026

🎯【!!!CAUTION!!!】When installing, pay attention to the direction of the rod! When scratching, use full force and evenly, the cracks must be deep! When opening, the red dot facing upwards! Do not stick the tiles too far into the pliers! Do not exceed thickness requirements! For large tiles please clamp both ends of cutting line! We strongly recommend testing and practicing with a few scrap tiles before using this cutter, because some skills are required. Read all the notes below this page! You must take out a few waste tiles for testing, because it has certain requirements on strength and operation methods, please operate on the waste tiles before using them normally.

🎯【Parameters】1.Theoretically no limit to max. cutting length, BUT we recommend max. 300cm (118”) 2. Cutting width 5cm-90cm (2”-36“), BUT you can cut max. 180cm (72") if placed along both sides3. Cutting thickness 0.5cm-1.2cm (0.2”-0.5”) Strong and durable, lever principle, save time and improve efficiency.

🎯【Why Choose Us】Professional and precise cutting of tiles, glass and mirrors, LIGHT only 1.6kg (3.6 lbs), so easy to carry and move this tile snap cutter. it can be used for professional tile/glass cutting, home decoration or DIY, designing student utensils, tile/glass restoration, free creation by art lovers.

🎯【Why Choose Us】Only need to CUT and OPEN the tile or glass. It has a wide range of uses: it can be used for professional tile/glass cutting, home decoration or DIY, designing student utensils, tile/glass restoration, free creation by art lovers, etc.

🎯【Parameters】Bull-Shaped Tile Glass Cutter can be used to score lines on surfaces like Glass, Mosaic, Tiles and Mirrors. The cutting thickness is 0.2"-0.48" (0.5cm-1.2cm), and the cutting width is min. 2" (5cm). The weight is 0.55lbs (0.25kg). 100% Satisfaction guarantee your choice.

🎯【Advantages】The buffer design can protect the surface of the tile and prevent the damage caused by the moment of cutting. The elastic design of the lower fulcrum prevents the tiles from falling when opened. The handle is ergonomically designed for long-term use without getting tired.

❤️Easy to cutter tiles/glass: The tile cutter is very light(only:1.5bl), and the tungsten carbide scoring wheel is sharp. Just press the hand holding the orange handle down to slide, and you can easily draw lines on the tiles

❤️Cutting size: Maximum cutting length: can be greater than 48 inches (1200mm), it is recommended not to exceed 120 inches (300mm); maximum direct cutting width: 48 inches (1200mm) can be cut through clever methods; cutting thickness: 0.24' - 0.6' (6mm - 15mm); minimum cutting width: 1.97' (50mm)

❤️Reasonable structure: The breaking pliers are die-cast from aviation aluminum. The main body of the manual tile cutter is made of alloy material, which is very strong and durable. The laser scale is used on the ruler surface, with two units of inch and cm, which fully conforms to your usage habits

🎯【!!!CAUTION!!!】When installing, pay attention to the direction of the rod! When scratching, use full force and evenly, the cracks must be deep! When opening, the black handle facing upwards! Do not stick the tiles too far into the pliers! For large tiles please clamp both ends of cutting line! We strongly recommend testing and practicing with a few scrap tiles before using this cutter, because some skills are required. Read all the notes below this page!

🎯【NEW DESIGN!!!】The NEW Super Large HANDLE makes opening easier! Only need to SCRATCH AND CLAMP/ROTATE! TWO Opening Modes can be chosen. The ergonomic handle design is easy to hold. The BUFFER design can protect the surface of the tile and prevent the damage.

🎯【Parameters】[1]Theoretically no limit to max. CUTTING LENGTH, BUT we recommend max. 300cm (118”) [2] CUTTING WIDTH 5cm-60cm (2”-24“), BUT you can cut max. 120cm (48") if placed along both sides [3] CUTTING THICKNESS 3-20mm(1/8”-3/4”) Strong and durable, lever principle, save time and improve efficiency.

🚀It is recommended to take disused tiles to practice cutting: How to stabilize the cutter wheel on the edge of the tile while moving. How to slide an even line. How to apply even force. It is not recommended to use directly for work!

🚀Tile cutter one side width up to 90cm. exchange tile cutter tool position can cut the width of 150cm (60") tiles. The length is recommended to be within 300cm, otherwise the pliers need big force and bad control. In fact, there is no limit to the cutting length, tile thickness is recommended to be no thicker than 1.2cm (0.5"). So easy tile cutter 48 inch,36 inch,60 inch,52 inch,30 inch,24 inch...

🚀Package includes 1 large cutter, 1 small cutter (cutting tiles, glass and mirrors), 1 tile pliers, 8 diamond blades of 6mm and 2 tungsten steel cutting wheels of 22mm (0.86") (both can cut tiles and glass, no need to buy separate cutter wheels).

●🎯【!!!CAUTION!!!】When installing, pay attention to the direction of the rod! When scratching, use full force and evenly, the cracks must be deep! Do not stick the tiles too far into the pliers! Do not exceed thickness requirements! For large tiles please cut both ends of scoring line! We strongly recommend testing and practicing with a few scrap tiles before using this cutter, because some skills are required. Read all the notes below this page! You must take out a few waste tiles for testing, because it has certain requirements on strength and operation methods, please operate on the waste tiles before using them normally. 4.0 GENERATION!!!!

●🎯【Parameters】[1] We recommend for LENGTH max. 300cm (118”). [2] WIDTH 5cm-90cm (2”-36“), BUT IF PLACED ALONG BOTH SIDES you can cut max. 180cm (72"). [3] THICKNESS 0.5cm-1.2cm (0.2”-0.5”). For large tiles please cut both ends of scoring line! 4.0 GENERATION!!!!!

●🎯【Why Choose Us】Professional and Precise cutting of tiles, glass and mirrors, NEW SUPER POWER TILE PLIERS!!!!! 4.0 GENERATION! it can be used for professional tile/glass cutting, home decoration or DIY, designing student utensils, tile/glass restoration, free creation by art lovers. Strong and durable, lever principle, save time and improve efficiency. 4.0 GENERATION!!!!!