Best Cir Kit Concepts Dollhouses in 2026

Our double conductor tapewire is the "heart" of all Cir-Kit wiring systems.

From its introduction in 1976 to the present it has been the predominant method of dollhouse wiring. Its use creates a printed circuit type layout and completely eliminates the congested wiring found in conventional systems. A super strong adhesive, exposed by the removal of a peel away paper carrier, ensures a secure grip on any surface. Since the copper foils are sandwhiched between two layers of transparent tape, the tape may be applied even over bare metal. The exposed transparent tape has a

See description for full details.

Detailed scale model for adult collectors. Not intended for children under 14.

Using the sconce adapter, a sconce may be installed on either a vertical or horizontal tape run and may be rotated up to 30 degrees in either direction for perfect alignment.

The adapter ring is fully brass plated making it suitable for even the most ornate of wall fixtures.

Complete step-by-step instructions, with detailed illustrations, are included in each package.

Same as pictured, but with brown wires.

These high quality bulbs are excellent for illuminating any part of a dollhouse or miniature room. Bulb wires may be attached to our miniature plugs or directly bradded into tape runs with 1/8" brass brads.

The 12-volt bulbs should be used in locations where bright illumination is necessary.

Same as pictured, but with green wires.

Use these bulbs wherever a larger and brighter flame bulb is desired.

The CK1010-26 bulb may be used with either a 1.5-volt battery or the CK1009G transformer. The CK1010-26 bulbs may be made into clear Christmas light strings by assembling 12 bulbs in series and connecting each end across a 12-volt transformer. 5,000 hour bulb life.

New Old Stock - In unopened package.

Replacement bulb for Cir-Kit Concepts Swivel-Head Flashlight #CK1043

Bulb measures .5" long by 0.125" in diameter

These high quality bulbs are excellent for illuminating any part of a dollhouse or miniature room.

Bulb wires may be attached to our miniature plugs or directly bradded into tape runs with 1/8" brass brads.

The grain-of-wheat (GOW) bulbs measure approximately 3/16" in diameter and draw between 40-60 ma.

Use these bulbs wherever a larger and brighter flame bulb is desired. Bulb may be used with any 12-volt transformer.

Current drain is approximately 40 ma for the 12-volt bulbs.

5,000 hour bulb life.

Same as pictured, but with black wires

(GOR) bulbs are ideal for those applications where minimum bulb size is desirable.

These bulbs are made with some of the smallest insulated wires available. Great attention has also been given to making the wire connections at the base of the bulb as unnoticeable as possible.

Same as picture, but with brown wires.

These sockets have been developed especially for use with the CK1010-5 and CK1010-12 series of wire terminal bulbs. When used with a CK1010-12 bulb they provide a "true-to-scale" candle look for miniature candlesticks, chandeliers and sconces.

Since the bulbs are merely plugged in, replacement in the event of failure is greatly simplified. The sockets are .089" in diameter and measure 3/16" in length.

(GOR) bulbs are ideal for those applications where minimum bulb size is desirable.

These bulbs are made with some of the smallest insulated wires available. Great attention has also been given to making the wire connections at the base of the bulb as unnoticeable as possible.

The GOR bulbs measure approximately 3/32" in diameter and draw between 40-60 ma.

This grain-of-rice (GOR) bulb is ideal for those applications where minimum bulb size is desirable.

These bulbs are made with some of the smallest insulated wires available.

Great attention has also been given to making the wire connections at the base of the bulb as unnoticeable as possible.

Same as pictured, but wires are black.

These high quality bulbs are excellent for illuminating any part of a dollhouse or miniature room. Bulb wires may be attached to our miniature plugs or directly bradded into tape runs with 1/8" brass brads.

The 12-volt bulbs should be used in locations where bright illumination is necessary and the 16-volt bulbs in areas where a soft, non-glaring light is preferred.

Use these larger heat shrink tubes for interconnecting heavier gauge wires. Each tube is black in color, measures 1" in length and shrinks to 1/2 the original size when heated.

Rated wire size and application: CK1033-6 (3/16" inside diameter) 18 gauge lamp cord wire.

Detailed scale model for adult collectors. Not intended for children under 14.

These 1.5 volt axial bulbs are a fraction the size of our popular micro bulbs and meet the challenge of even the smallest lighting projects. Ideal as light sources for both 1/4" and 1/2" scale miniatures.

Both size axial bulbs may be operated in parallel either from a 1.5 volt battery pack or from our CK1009G 1.5 volt transformer. The larger diameter CK1010-19 bulbs are electrically balanced and may be operated 12 in series across a 12-volt transformer.

The bulbs may also be used in model railroading for locomotive number boards or classification lights as well as interior lighting for smaller scale cars. 1,000 hour bulb life.

Use this 115 vac lighting set for backlighting any vignette box or miniature room. Locate the 4-watt bulb behind a back wall to create a completely hidden indirect light source.

The plug and in-line switch are removable and allow the power cord to be easily pulled through a small feed hole.

Overall length 6'. No transformer necessary.

Same as pictured, but with black wires

The grain-of-rice (GOR) bulbs are ideal for those applications where minimum bulb size is desirable.

These bulbs are made with some of the smallest insulated wires available. Great attention has also been given to making the wire connections at the base of the bulb as unnoticeable as possible.