Best Fxtul in 2026

【MULTIPLE TEST FUNCTIONS】The smoke machine automotive leak detector supported crankcase system test, intake system test, car sealing test, fuel tank system test, turbo leaks test, various pipe fittings test, exhaust system test, EVAP system test. (Note: Not applicable to air conditioning system piping).

【TWO-MODE】Air mode and smoke mode, the smoke detector built-in air pump and smoke generator, so it does not rely on additional air machine. Professional automobile smoke leak detection tool, using visible smoke to quickly locate the leak hole. The smoke can be produced within 30 seconds, dramatically reducing diagnostic time. Perfect for Mobile Automotive Repair!

【SPECIFICATIONS】The leak down detector built-in smoke generator with smoke output value: 0-8 L/min, power supply: 12V Vehicle battery, < 8Amp, output pressure: <1.2 Bar, heating material: mineral oil or baby oil (oil not included).

【MULTIPLE DETECTION FUNCTIONS】The leak detector has a variety of test functions and can do smoke testing of multiple systems, including crankcase systems, intake systems, car sealing, fuel tank systems, low pressure turbo leaks, various pipe fittings, exhaust systems, EVAP systems. Note: Not suitable for air conditioning system piping.

【QUICK DETECTION】The automobile smoke leak detector is specially designed to detect the leakage of automobile fuel and gas pipelines, heating special oil (mineral oil or baby oil) into smoke, and then pressing it into the sealed pipeline system. If there is a leak, you will find smoke.

【FLOW METER & PRESSURE GAUGE】The smoke leak detector is equipped with flow meter and pressure gauge. All data are clear at a glance, which helps you better control the smoke effect. And the EVAP Leak detection unit has an intelligent protection device with overheating.

📣【POWERFUL HEAD-UP DISPLAY】 OBD HUD is a small car gadget with powerful functions, which is suitable for vehicles without a tachometer, an engine temperature gauge, and fuel consumption display functions. Highly compatible and supports OBD standard protocols for cars manufactured after 2008

📣【EARLY ALARM FUNCTIONS】Support multiple early car alarm functions that can improve driving safety: water temperature early alarm, over-speed early alarm, shifting reminding early alarm, and vehicle fault early alarm. In addition, you can read vehicle data stream, scan, and clear DTCs at your discretion, and reduce repair costs

📣【ACCURATE ORIGINAL VEHICLE DATA】 OBD2 gauge display reads the original car data through the OBD interface, such as speed, RPM, coolant temp, voltage, fuel consumption, distance, and other data you may need to read during driving. The data is highly accurate and almost identical to the original dashboard

👍👍👍【Professional Diagnostic Tool】The catalytic converter tester is designed to help you quickly and accurately understand the condition of your vehicle's exhaust system, allowing you to diagnose problem areas in your exhaust system back pressure so you can take your next steps. The pressure should be lower than 1.25psi at idling speed, and lower than 3psi at 2500rpms. Use this exhaust gauge to gain vital knowledge about your vehicle's exhaust system and prevent poor engine performance.

👍👍👍【Accurate Gauge】The exhaust back pressure tester's 2.5" inch gauge has easy-to-read markings in psi and bar. 3 colors to indicate the good or bad status, the highly visible mark greatly helps users to directly read the data. The exhaust pressure tester is tested at idle and 2500rpm. Pressure should be less than 1.25psi at idle and less than 3psi at 2500rpm.

👍👍👍【Easy to Use】Just disconnect the sensor wires and remove the sensor. Install the sensor adapter. And then push the hose end onto the adapter and make the pressure test. The adapter with exhaust back pressure gauge are M12 and M18. Start car, read data, 6ft hose with gauge tester allows user to test from driver seat.

【High Accuracy】The digital handheld manometers has the characteristics of high precision and wide range. Measurement range: ±35.00psi; Accuracy: ±0.3%FSO (at 25°C) ; Repeatability: ±0.25% (Max ±0.5%FSO); Linearity/Hysteresis: ±0.1%FSO

【11 Selectable Units】Bar, ozin2, psi, inHg, mbar, mmHg, cmH2O, ftH2O, inH2O, kgcm2, kPa

【Data Record】The digital manometer can record test data for easy viewing by the user after the test. Click the "zero" button after use to get your readings accurate

【Heavy Duty Nut Splitter】The nut breaker tool can be used to safely remove corroded or damaged nuts without damaging the bolt threads, helping you better solve the disassembly problem.

【Easy to Use】Just rotate the nut splitter bolt to work on the target nut. Very easy to use. You may prepare a wrench help you to do this work. You can use these splitting tools to cut damaged nuts off, then solve the difficult problem of removing.

【Premium Quality】Heavy duty nut splitter tool is made of hard bearing steel, fully forged, tempered, mirror polished, well made, resistant to corrosion and rust, hard and strong for long term use. It is a high quality nut splitter breaker that you can use with confidence.

【System Diagnosis Features】The Motocycle diagnostic tool Support engine / ABS / Tire pressure / Anti-theft and other systems, It can quickly read and clear diagnostic trouble codes, view freeze frame, display data stream and do active tests, get vehicle information, You are allowed to perform a complete and deep detection for your motorcycles, rather than send it directly to repair shop, very suitable for diyers.

【EASY TO USE】FXTUL M3 is a handheld motorcycle diagnostic tool for mainstream motorcycle brands and can help technicians diagnose problems faster and make repairs. This tool has functions such as voltage detection, multi-language selection, and unit switching. It has a clear interface and is easy to operate. It is a good helper for motorcycle maintenance.

【Wide Compatibility】support the diagnosis of Asian, European and American multi-brand motorcycles, M3-C is suitable for SUZUKI, Vespa, EUROV and OBD2 motorcycles. Supports 11 languages, You can switch the language you need anytime.

✯✯✯【Ultra-safe Design】Includes a pressure monitoring gauge to observe the flow of liquid and a safety valve (preset at 43 PSI) to relieve pressure in case of overload. Extraction working pressure: max. 170psi. / Dispensing working pressure: max. 43psi. Our transmission fluid pump is made of corrosion-resistance material, and it can withstand high pressure and also easy to wash. There will be no air leakage, cracking or liquid spilling, and also guarantee your safety.

✯✯✯【Configured with 20 adapters for superb compatibility】The fluid transfer pump comes with 20 common adapters, that fit a variety of automobiles, including famous cars like BMW, Porsche, VW, Honda, Audi, and many others. Simple push-on coupler design, You can flush and change the oil for your vehicles. All the adapters are installed in a toolbox, with clear model identification.

✯✯✯【8L Capacity】Our pneumatic ATF pump has an 8L large capacity. 2M PU hose with one touch controller gun to connect with transmission filling adapter enables the steady operation of the flow volume and easy to do the dispensing jobs. Without the splashing during the work. It provides an easy way to extract and dispense transmission fluid quickly and cleanly. It's an ideal tool for oil replacement.

【Widely Used Adapter】Make leak testing with a smoke machine a whole lot easier! It's designed to fit even large intakes on V8 vehicles.

【How Does it Work?】Fit the cone into diagnostic site (such as the intake boot/duct or exhaust tailpipe) and inject smoke with a smoke machine to test for system leaks

【NEW LARGER SIZE!】Will fit almost all exhaust tips and intake boots. Made for larger openings with a diameter up to 4.2 inches (107mm) and as small as 1 inch (26mm)

Contains one application of oil and fuel system UV leak detection dye

For use in engine oil transmissions power steering systems and gas and diesel fuel systems

Compatible with all weights of petroleum based lubricant

【MULTIPLE TEST FUNCTIONS】The smoke machine automotive leak detector supported crankcase system test, intake system test, car sealing test, fuel tank system test, turbo leaks test, various pipe fittings test, exhaust system test, EVAP system test. (Note: Not applicable to air conditioning system piping).

【TWO-MODE】Air mode and smoke mode, the smoke detector built-in air pump and smoke generator, so it does not rely on additional air machine. Professional automobile smoke leak detection tool, using visible smoke to quickly locate the leak hole. The smoke can be produced within 30 seconds, dramatically reducing diagnostic time. Perfect for Mobile Automotive Repair!

【SPECIFICATIONS】The leak down detector built-in smoke generator with smoke output value: 0-8 L/min, power supply: 12V Vehicle battery, < 8Amp, output pressure: <1.2 Bar, heating material: mineral oil or baby oil (oil not included).

Compatible with ALL Automotive Smoke Testers

Make leak testing with a smoke machine via larger openings a whole lot easier!

Premium Durable Quality. Automotive Grade.Simply fit the cone into diagnostic site and inject smoke to test for system leaks

【MULTIPLE DETECTION FUNCTIONS】The leak detector has a variety of test functions and can do smoke testing of multiple systems, including crankcase systems, intake systems, car sealing, fuel tank systems, low pressure turbo leaks, various pipe fittings, exhaust systems, EVAP systems. Note: Not suitable for air conditioning system piping.

【QUICK DETECTION】The automobile smoke leak detector is specially designed to detect the leakage of automobile fuel and gas pipelines, heating special oil (mineral oil or baby oil) into smoke, and then pressing it into the sealed pipeline system. If there is a leak, you will find smoke.

【FLOW METER & PRESSURE GAUGE】The smoke leak detector is equipped with flow meter and pressure gauge. All data are clear at a glance, which helps you better control the smoke effect. And the EVAP Leak detection unit has an intelligent protection device with overheating.

Direct replacement - this evaporative emissions system leak detection pump is designed to match the fit and function of the original pump on specified applications

Restores functionality - reliable replacement for an original part that has clogged or failed due to emissions control system damage

Durable construction - this part is made from quality materials to ensure reliable performance and long service life

EASY TO USE: The Smoke Machine Automotive with easy-use function and portable design, can help mechanic produce lots of smoke within 30s to detect the leaks in pipe system (by heating up baby oil). Dramatically reducing diagnostic time.

3 MAIN FUNCTIONS: Air-tightness Check, Evaporating Fuel Leakage Check, and Over-heat & Anti-frost protection. If it exceeds the working limit (Over 167°F) it will power off automatically. The evap smoke machine has its own air pump. It does not rely on other air machine and connect the detector with DC12V battery.

SUPPORTED VARIOUS SYSTEM TEST : Included EVAP System Test, Intake System Test, Exhaust System Test, Fuel Tank System Test and Car Sealing Test. (Note: Not applicable to air conditioning system piping) It can quick to find evap leaks.

【Why Need It】For example: 1. The rupture of the vacuum hose will cause the mixture to be too thick, the idle speed will increase, the hot car will not start well, the engine will surge during acceleration, the fuel consumption will increase significantly, and the exhaust pipe will emit black smoke. 2. Blocking will cause the idle speed to drift, and the idle speed is easy to stall. 3. Air leakage in the vacuum tube will cause the engine to run weakly

【EVAP Detection】American cars that began production in 1996 are equipped with EVAP service ports; in most American cars, the EVAP service port is usually located in the engine compartment, but the EVAP service port of some special models may be located in other locations. Open the plastic cover of the EVAP service port, then use the spool wrench to remove the check valve clockwise, then install the EVAP service port adapter, and introduce smoke from the port into the EVAP leak detection system.

【Wide Testing Range】Built-in air pump,The smoke leak detector can do smoke testing of multiple systems, such as EVAP systems, Intake Systems, Cooling / EGR /Exhaust Systems, Crankcase Systems, Engine Airtightness, Vacuum Leaks, Low Pressure Turbo leaks.Applicable cars, motorcycles, snowmobiles, off-road vehicles, ATVs, light trucks and speedboats boats.

【Why Need It】For example: 1. The rupture of the vacuum hose will cause the mixture to be too thick, the idle speed will increase, the hot car will not start well, the engine will surge during acceleration, the fuel consumption will increase significantly, and the exhaust pipe will emit black smoke. 2. Blocking will cause the idle speed to drift, and the idle speed is easy to stall. 3. Air leakage in the vacuum tube will cause the engine to run weakly

【Built-in Air Pump】Customers do not need to purchase additional air pumps, we use high-quality materials, after many tests, please rest assured to use. You can save more time and money

【EVAP Detection】American cars that began production in 1996 are equipped with EVAP service ports; in most American cars, the EVAP service port is usually located in the engine compartment, but the EVAP service port of some special models may be located in other locations. Open the plastic cover of the EVAP service port, then use the spool wrench to remove the check valve clockwise, then install the EVAP service port adapter, and introduce smoke from the port into the EVAP leak detection system.

【Multi Functions】Tightness Test, Intake System Test, Exhaust System Test, Cooling System and Overheating Protection. Built-in air pump and smoke generator, so it does not rely on other air machine, perfect for Mobile Automotive Repair!

【Fast Smoke Output】The smoke can be produced within 10 seconds, and with stable and large amount of smoke output after switch-on (by heating up Baby Oil). Dramatically reducing diagnostic time.

【Convenient Design】Comes with a hook allows you to hang it on your hood latch, the conical adapter will fit most intakes, and the 1.5m smoke hose can help reach and connect perfectly, not harm the EVAP system.

Direct replacement - this evaporative emissions system leak detection pump is designed to match the fit and function of the original pump on specified applications

Restores functionality - reliable replacement for an original part that has clogged or failed due to emissions control system damage

Durable construction - this part is made from quality materials to ensure reliable performance and long service life

【Excellent Quality】AUTOOL Easy Intake Adapter is made of high-quality silicone, with strong sealing, softness, high temperature resistance, good elasticity, and tear resistance.All Easy Intake Adapters have undergone multiple simulation tests，ensure can detect intake and exhaust leakage more quickly and accurately

【Fast and Convenient】AUTOOL Easy intake adapter is an inflatable block-shaped airbag with a pressurized steam channel, which is used for intake and exhaust smoke test. The wall thickness is 1.5mm and its diameter can be expanded to 121mm. It helps technicians to quickly and easily test the entire intake or exhaust system，Note: Please make sure the intake/exhaust diameter is bigger than 2".

【Humanized Design】Compared to traditional,AUTOOL Easy intake adapter with a steel ring removed at the end in order to use a smaller fitting.can be tested the intake/exhaust diameter is bigger than 2" more quickly and accurately leakage .

【EASY TO USE】The smoke machine automotive can be powered by the car’s battery, and Shop Air driven to increase duribility and ensure big smoke flow And can quickly generate smoke

【CONVENIENT TOOL FOR MECHANICS】Fuel Leak Detector designed for detecting the leakage of pipe systems on cars, motorcycles, snowmobiles, ATV, light trucks, boats

【SPECIFICATIONS VOLTAGE】Automotive smoke machine DC 12V. Smoke output pressure:0.5PSI. Smoke output volume: ＜8LPM. Smoke current: 6 AMP.

Direct replacement - this evaporative emissions system leak detection pump is designed to match the fit and function of the original pump on specified applications

Restores functionality - reliable replacement for an original part that has clogged or failed due to emissions control system damage

Durable construction - this part is made from quality materials to ensure reliable performance and long service life

🚗【Diagnose All Types of Leaks】🚗The SM603 smoke machine automotive can help you detect accurately the leakage of EVAP system, intake/exhaust system, vacuum leaks, sealing test, fuel tank system, turbo, crankcase system, various pipe fittings , Throttle Shafts, Door&Windows seals, Oil Leaks and more! It can output the smoke within seconds, improve the efficiency of diagnose dramatically.

🚗【Advanced and Safe】🚗The Romondes SM603 evap smoke machine with thick smoke output detects even the smallest leaks. It is safe and reliable as there is no need to start the vehicle during use. Moreover, when this smoke leak detector can be smart power off, the power will be automatically shut off when it exceeds the 75 ℃ housing limit.

🚗【Flow meter】🚗SM603 automotive smoke machine provides a quick visual indication of the amount of smoke passing through the system being tested. Adjustable flow meter helps you control the amount of smoke easily and also used to lock out the system under test and observe any pressure decay on the pressure gauge.

▶ Convenient Automotive Tool - RTRHINOTUNING Smoke Leak Detector is a professional auto pipe leak detect tool. Designed for detecting the leakage of pipe systems on cars, motorcycles, snowmobiles, off-road vehicles, ATVs, light trucks and speedboats boats, You will quickly find the leak point in pipe via the smoke. One of the best tools you will ever own! If it leaks a smoke machine will find it.

▶ Working Type - The leak tester will turn smoke oil (USP Mineral Oil / Baby Oil) into smoke, then blow smoke into pipe system, you will find leak point in pipe via the smoke. In brief, our smoke detector can quickly make constant smoke to find leak. The vacuum smoke machine has its own Air Pump without relying on other machines. Simply connect the detector with the DC12V battery, it can output thick smoke within 20s after turning on.

▶ Application - Crankcase System Test, Intake System Test, Exhaust Systems Test, Fuel Tank System Test, Turbo System Test, Cooling System Test, Various Pipe Fittings Test. The Car Pipe leak Detector ​can be also be used to find other leaks, oil leaks, wind water and weatherstripping leaks; tractor & car cabs, EGR and exhaust systems, the list goes on.

Direct replacement - this evaporative emissions system leak detection pump is designed to match the fit and function of the original pump on specified applications

Restores functionality - reliable replacement for an original part that has clogged or failed due to emissions control system damage

Durable construction - this part is made from quality materials to ensure reliable performance and long service life

Direct replacement - this evaporative emissions system leak detection pump is designed to match the fit and function of the original pump on specified applications

Restores functionality - reliable replacement for an original part that has clogged or failed due to emissions control system damage

Durable construction - this part is made from quality materials to ensure reliable performance and long service life

[HOW TO WORK]: Firstly fill 20ml test oil, then simply connect the DC12V battery, it starts to work. Soon thick smoke outputs into sealed pipe system. You can find the leak point easily.

[WHY IS IT NEEDED]: Must-have tool for vehicle techs. It has its own Air Pump without relying on other machines and Pressure Gauge with precise scales. By observing the pressure gauge, the leakage situation is clear at a glance.

[WHAT IS ITS STANDOUT]: Smoke tester is detachable, compact, and easy to store, time-efficient and labor-free, and is widely used in various auto repair shops. Comes with EVAP adapters, it can help you apply with EVAP System of all vehicles to quickly find out the leak parts.

Easiest Method to Leak Test EVAP Systems

Fits All Vehicles

Precision Machined

Built in Air Pump - All you'll need is to use your vehicle's 12V Battery

Approved Smoke Fluid - Included.

Modes - Air mode to verify leaks even before introducing smoke. Smoke mode to introduce smoke into vehicle system for leak detection.

✅【HIGH SENSITIVE AND QUICK RESPONSE】The combustible gas detector is equipped with high-performance sensors and flexible probe , ±500PPM ultra-high sensitivity detection, 2 seconds ultra-fast response speed, automatic calibration within 30 seconds of booting, 360° ultra-flexible detection, 270mm metal hose, with backlight screen, temperature measure C/°F, 10 minutes automatic shutdown function More energy-saving and environmental protection.(3pcs AAA batteries included)

✅【ULTRA-CLEAR COLOR DISPLAY & AUDIBLE & VISUAL ALARM】The gas detector adopts VA reverse display color screen, ultra-clear digital and analog dual display, and simple button operation. Audible and visual alarm--50-50000PMM or 0.1%-100%LEL alarm range, If the detected leakage value is higher than 25% LeL / 12500PPM, the gas detector will emit a continuous beep and the screen will also display ”HIGH”.

✅【MULTIPLE DETECTABLE GASE】Detectors combustible & explosive gas leaks from methane, natural gas, propane, co, sewer gas, ethanol, coal gas, acetone, acetylene, alcohol, ammonia, benzene, butane, ethanol, ethylene, oxides, petrol, hexane, hydrogen, fuel and other flammable gases.