Best Digital Pressure Probes in 2026

It is an environmental sensor with temperature, barometric pressure that is the next generation upgrade to the BMP085/BMP180/BMP183.

The BMP280 is an absolute barometric pressure sensor especially designed for mobile.

This sensor is great for all sorts of weather sensing and can even be used in both I2C and SPI!

BMP180 is a high-precision, small size, ultra-low power pressure sensor that can be used in mobile devices

Its performance excellence, the absolute accuracy of the lowest can reach 0.03hPa, and low power consumption, only 3μA

BMP180 powerful 8-pin ceramic leadless chip carrier (LCC) ultra-thin package, you can directly through the I2C bus connected with a variety of microprocessors

This Kit contains with 3pcs of digital sensor module, which can be independently enabled / disabled, which can measure not only the temperature humidity, but also the pressure.

The BME280 sensor is great for all sorts of weather sensing and can even be used in both I2C and SPI! For simple easy wiring, go with I2C. If you want to connect a bunch of sensors without worrying about I2C address collisions, go with SPI.

Our BME280 Sensor is the best low-cost, precision sensing solution for measuring barometric pressure with ±1 hPa absolute accuraccy, and temperature with ±1.0°C accuracy. Because pressure changes with altitude, and the pressure measurements are good, you can also use it as an altimeter with ±1 meter accuracy.

This Kit contains with 3pcs of digital sensor module, which can be independently enabled / disabled, which can measure not only the temperature humidity, but also the pressure.

The BME280 sensor is great for all sorts of weather sensing and can even be used in both I2C and SPI! For simple easy wiring, go with I2C. If you want to connect a bunch of sensors without worrying about I2C address collisions, go with SPI.

Our BME280 Sensor is the best low-cost, precision sensing solution for measuring barometric pressure with ±1 hPa absolute accuraccy, and temperature with ±1.0°C accuracy. Because pressure changes with altitude, and the pressure measurements are good, you can also use it as an altimeter with ±1 meter accuracy.

Compatible with all Fluke and most popular digital multimeters

Digital pressure and vacuum measurements in a single module

Transducer sealed in 316 stainless steel compatible with variety of liquids and gases

This module adopts high precision AD sampling chip and 0-40KPa air pressure sensor.

Adopts 5K ohm resistor bridge sensor.

Pressure: 0-40KPa., Voltage: 3.3-5V. The specific air pressure value needs to be calculated

The BME280 sensor is great for all sorts of weather sensing and can even be used in both I2C and SPI! For simple easy wiring, go with I2C. If you want to connect a bunch of sensors without worrying about I2C address collisions, go with SPI.

Our BME280 Sensor is the best low-cost, precision sensing solution for measuring barometric pressure with ±1 hPa absolute accuraccy, and temperature with ±1.0°C accuracy. Because pressure changes with altitude, and the pressure measurements are good, you can also use it as an altimeter with ±1 meter accuracy.

Supply Voltage: 1.8 - 5V DC Interface: I2C (up to 3.4MHz), SPI (up to 10 MHz)

The BMP280 sensor is a precision sensor, is soldered onto PCB, measure the pressure and the temperature.

It is an environmental sensor with temperature, barometric pressure that is the next generation upgrade to the BMP085/BMP180/BMP183.

Temperature humidity module is great for all sorts of weather sensing and can even be used in both I2C and SPI.

Air pressure sensor module pressure: 0-40KPa; Voltage: 3.3-5V the specific air pressure value needs to be calculated; Voltage: 3.3-5V

This module adopts high precision AD sampling chip and 0-40KPa air pressure sensor, it can connect 2.5mm soft tube and detect the water level and other air pressure

Adopt 5K ohm resistor bridge sensor, and specific air pressure value needs calculating.

BMP388 indludes a new FIFO functionality. This greatly improves ease of use while helping to reduce power consumption of the overall device system during full operation. The integrated 512 byte FIFO buffer supports low power applications and prevents data loss in non-real-time systems.

The sensor is more accurate than its predecessor BMP280, covering a wide measurement range from 300 hPa to 1250 hPa. This new barometric pressure sensor exhibits an attractive price -performance ratio coupled with low power consumption.

Due to the built-in hardware synchronization of the pressure sensor data and its ability to synchronize data from extermal