Best Temperature Pressure Probes in 2026

Pressure Probe

LED color indications

High or low side switch

Grounded thermocouple thermistor . The K thermocouple temperature sensor is waterproof . This is a water tight sensor probe

The K type temperature sensor probe temperature range is 0~500℃ ( 932 Fahrenheit ) . Accuracy : 0.2 .

This K temperature sensor is rustproof , it is made from stainless steel . Water proof Insulation Lead

This Kit contains with 3pcs of digital sensor module, which can be independently enabled / disabled, which can measure not only the temperature humidity, but also the pressure.

The BMP280 sensor is great for all sorts of weather sensing and can even be used in both I2C and SPI! For simple easy wiring, go with I2C. If you want to connect a bunch of sensors without worrying about I2C address collisions, go with SPI.

Our BMP280 Sensor is the best low-cost, precision sensing solution for measuring barometric pressure with ±1 hPa absolute accuraccy, and temperature with ±1.0°C accuracy. Because pressure changes with altitude, and the pressure measurements are good, you can also use it as an altimeter with ±1 meter accuracy.

100PSI PRESSURE TRANSDUCER - Convert the physical parameters of the gas , liquid and other physical parameters of the pressure sensor into a standard electrical signal.

WIDE APPLICATION - Plug and play for fuel, oil, air, water pressure inputs, can be used in oil tank, gas tank, etc.

PREMIUM MATERIAL - Made from top grade 316 stainless steel & high temperature resistant plastic, endure all kinds of working environment.

Not only the pressure and the temperature, this sensor can measure humidity.

Make sure to put SDO to high to get address 0x77. This will work with Adafruit BME280 library perfectly.

BME280 is a precision sensor, is soldered onto PCB. It uses both I2C and SPI (supports 3-, 4-wire SPI) interface.

Not only the pressure and the temperature, this sensor can measure humidity.

Make sure to put SDO to high to get address 0x77. This will work with Adafruit BME280 library perfectly.

BME280 is a precision sensor, is soldered onto PCB. It uses both I2C and SPI (supports 3-, 4-wire SPI) interface.

It is an environmental sensor with temperature, barometric pressure that is the next generation upgrade to the BMP085/BMP180/BMP183.

The BMP280 is an absolute barometric pressure sensor especially designed for mobile.

This sensor is great for all sorts of weather sensing and can even be used in both I2C and SPI!

This Kit contains with 3pcs of digital sensor module, which can be independently enabled / disabled, which can measure not only the temperature humidity, but also the pressure.

The BME280 sensor is great for all sorts of weather sensing and can even be used in both I2C and SPI! For simple easy wiring, go with I2C. If you want to connect a bunch of sensors without worrying about I2C address collisions, go with SPI.

Our BME280 Sensor is the best low-cost, precision sensing solution for measuring barometric pressure with ±1 hPa absolute accuraccy, and temperature with ±1.0°C accuracy. Because pressure changes with altitude, and the pressure measurements are good, you can also use it as an altimeter with ±1 meter accuracy.

[PRE-SOLDERED]: Solderless! Pins already attached. Ready to plug in and go.

[COMPATIBILITY]: Perfect for all models of Raspberry Pi, Arduino, and various microcontrollers.

[ENVIRONMENTAL SENSOR]: Measures Pressure, Humidity, and Temperature with I2C and SPI Interfacing.

【350 Ohm】 A resistive strain gauge sensor with a 350 ohm nominal resistance which varies when a force is applied. By measuring the change in the sensors resistance, a measurement of the force applied to it can be obtained.

【Constantan Foil】The substrate is made of the modified phenolphthalein, and the grid is made of constantan foil.

【High Precision】With high precision and good static measurement stability, the weighing sensor is suitable for 0.02 level sensor.

This Kit contains with 3pcs of digital sensor module, which can be independently enabled / disabled, which can measure not only the temperature humidity, but also the pressure.

The BME280 sensor is great for all sorts of weather sensing and can even be used in both I2C and SPI! For simple easy wiring, go with I2C. If you want to connect a bunch of sensors without worrying about I2C address collisions, go with SPI.

Our BME280 Sensor is the best low-cost, precision sensing solution for measuring barometric pressure with ±1 hPa absolute accuraccy, and temperature with ±1.0°C accuracy. Because pressure changes with altitude, and the pressure measurements are good, you can also use it as an altimeter with ±1 meter accuracy.

EASY TO INSTALL: The pressure transducer sender has light weight and small dimension, convenient to install and operate

DURABLE: The thread pressure transducer has stainless steel body, with high quality ceramic pressure chip

HIGH SENSITIVITY: The air pressure transducer has ±2%FS small output error, full temperature range, high sensitivity and accuracy

Features: Uses I2C interface (Qwiic-enabled): I2C Addresses: 0x76 (Default) or 0x77, 2x Qwiic Connectors; Operating voltage range: 1.71V - 3.6V, Typically 3.3V if using the Qwiic cable; Typical current consumption (varies based on mode and active sensor): 2.1 µA to 18mA, 0.15 µA (sleep mode), 3.9 mA in standard gas scan mode

Relative humidity: Operating range: 0% to 100%, Absolute Accuracy: ±3%RH, Resolution: ±0.008%RH; Temperature: Operating range: -40°C to +85 °C, Absolute Accuracy: ±1.0°C, Resolution: 0.01°C

Pressure: Operating range: 300hPa - 1100hPa, Absolute accuracy: ±60Pa (0°C to 65°C), Resolution: 0.18PA, highest oversampling; Gas: F1 score for H₂S scanning: 0.92, Standard scan speed: 10.8 sec/scan, Sensor-to-sensor deviation: ± 15% ± 15

Wireless Pressure Sensor

Use your Apple or Samsung device to measure pressure and temperature

Small size, easy to use, 100PSI, 300PSI, 1,000PSI, 5,000PSI, 10,000PSI also available

The BME280 sensor is great for all sorts of weather sensing and can even be used in both I2C and SPI! For simple easy wiring, go with I2C. If you want to connect a bunch of sensors without worrying about I2C address collisions, go with SPI.

Our BME280 Sensor is the best low-cost, precision sensing solution for measuring barometric pressure with ±1 hPa absolute accuraccy, and temperature with ±1.0°C accuracy. Because pressure changes with altitude, and the pressure measurements are good, you can also use it as an altimeter with ±1 meter accuracy.

Supply Voltage: 1.8 - 5V DC Interface: I2C (up to 3.4MHz), SPI (up to 10 MHz)

★Not only the pressure and the temperature, this sensor can measure humidity.

★Make sure to put SDO to high to get address 0x77. This will work with BME280 library perfectly.

★BME280 is a precision sensor, is soldered onto PCB. It uses both I2C and SPI (supports 3-, 4-wire SPI) interface.

Temp Range: -40C to 85C - Humidity Range: 0 - 100% RH, =-3% from 20-80%

Pressure Range: 30,000Pa to 110,000Pa, relative accuracy of 12Pa, absolute accuracy of 100Pa

Altitude Range: 0 to 30,000 ft (9.2 km), relative accuracy of 3.3 ft (1 m) at sea level, 6.6 (2 m) at 30,000 ft.

【High Precision】: ±2%FS small output error, full temperature range, high sensitivity and accuracy

【Widely Used】: Widely used in oil tank, gas tank and diesel tank to detect oil, fuel, diesel, gas, water or air pressure

【Voltage Protection】: Complete surge voltage protection function, safe for use

BMP280 3.3V Atmospheric Pressure Sensor Module is an environmental sensor with temperature, barometric pressure that is the next generation upgrade to the BMP085/BMP180/BMP183.

The BMP280 is an absolute barometric pressure sensor especially designed for mobile.This sensor is great for all sorts of weather sensing and can even be used in both I2C and SPI.

This precision sensor is the best low-cost, precision sensing solution for measuring barometric pressure with ±1 hPa absolute accuraccy, and temperature with ±1.0°C accuracy.

[Stable Performance]: The pressure transducer adopts precision compensation technology and sensitive components, which is stable and reliable

[High Accuracy]: ±2%FS small output error, including nonlinear, hysteresis error and repeatability, full temperature range

[Surge Voltage Protection]: The pressure gauge transducer has a complete surge voltage protection function

4 in One: Light intensity + Temperature + Humidity + Atmospheric pressure module.

GY-39 is a light intensity temperature humidity atmospheric pressure sensor integrated module, direct serial output. Communication method: MCU_IIC/MCU_serial port/sensor chip IIC bus.

You can use the MCU on the module to read various data. After the MCU calculates, it outputs the calculated practical data directly. It supports serial port/i2c.

Multi‑purpose, the sensor can sense atmospheric pressure and temperature in many ways.

Made of synthetic cardboard material in high quality, the sensor keeps high reliability and excellent long;term stability.

And scope of work includes ;40 to +85°C temperature, and 1100 hPa pressure.

The BMP280 sensor is a precision sensor, is soldered onto PCB, measure the pressure and the temperature.

It is an environmental sensor with temperature, barometric pressure that is the next generation upgrade to the BMP085/BMP180/BMP183.

Temperature humidity module is great for all sorts of weather sensing and can even be used in both I2C and SPI.

BMP388 indludes a new FIFO functionality. This greatly improves ease of use while helping to reduce power consumption of the overall device system during full operation. The integrated 512 byte FIFO buffer supports low power applications and prevents data loss in non-real-time systems.

The sensor is more accurate than its predecessor BMP280, covering a wide measurement range from 300 hPa to 1250 hPa. This new barometric pressure sensor exhibits an attractive price -performance ratio coupled with low power consumption.

Due to the built-in hardware synchronization of the pressure sensor data and its ability to synchronize data from extermal