Best Lcyindu in 2026

【Strong Compatibility】: 5T hydraulic puller can be operated horizontally or vertically without site restrictions. It has 2"(50 mm) axis travel with 7.8" (200 mm) max. reach and 7.8"(200 mm) max. spread.

【Durable Material】: The ZYL-5 hydraulic gear puller is made of heavy-duty forged alloy steel, featuring superior strength and no oil leakage. It's very sturdy and possesses 5T maximum capacity and a long service time.

【Adjustable jaws】: You can install two or three jaws and adjust the height as required. In addition, the pump head of the hydraulic bearing puller can rotate 360 degrees, which is convenient for you to operate and use tools.

【Strong Compatibility】: ZYL-10 10T hydraulic puller can be operated horizontally or vertically without site restrictions. It has 2.36" / 60mm axis travel with 6.3" / 160mm max. reach and 9.84" / 250mm max. spread.

【Adjustable jaws】: You can install two or three jaws and adjust the height as required. In addition, the pump head of the hydraulic bearing puller can rotate 360 degrees, which is convenient for you to operate and use tools.

【Durable Material】: The hydraulic gear puller is made of heavy-duty forged alloy steel, featuring superior strength and no oil leakage. It's very sturdy and possesses 10T maximum capacity and a long service time.

The Gearwrench Hammer Puller Set provides a wide range of puller applications including flange type axles, oil seals, and other press fit Parts

Jaws can be set up for 2 or 3 jaw internal or external pulling jobs

5-1/2 lb slide hammer has a 5/8-18 thread

Quickly Flushes Out Old Grease and Repacks Bearings with Less Mess..Fit Type: Universal

The Handy Packer works on bearings up to 3 1/2" O.D.

The grease stays in the tool cavity, not on your hands. To pack a bearing, place the bearing on the piston.

OTC's 9-Way Slide Hammer Puller Set is ideal for pulling flange-type rear axles and most front-wheel drive hubs

Internal and external jaws provide a variety of combinations to pull bearings, gears, and seals

Two- and three-way cross blocks and cone provide the perfect jaw configuration for most jobs

Set contains slide hammer and popular attachments needed for servicing flange type floating rear axle bearing and seals in most late model rear wheel drive cars and light trucks

Includes 3 sizes of rear axle bearing pullers

Slide hammer tee bar and Slide hammer 5 LB head weight

GXL Carrier & Pinion Bearing Puller Dana 30, 40, 60, 70, 80, Ford 10.25 Clamshell Design

Ford 10.25" & Ford 10.5"

This tool is not used for removing pinion bearings on Dana 80.

PRACTICAL DAMAGE-FREE SEPARATOR: The ABN Bearing Puller with 1/2" to 4-5/8” Inch Jaw – Splitter Tool for Wheel Hub, Gear Pinion, Bearing Separator professionally applies even pressure to smoothly separate bearings and remove gears without damage

VERSATILE USES: Removes bearings, pinions, gears, pulleys, steering wheels, and fittings from shafts; For automobiles, ATVs, and power sport vehicles

DURABLE FOR HEAVY-DUTY APPLICATIONS: Constructed from heat-treated and chrome-plated steel with a black oxide finish for rust-resistance, strength, and longevity

Manual puller with three jaws for extraction of most shaft-fitted parts, including bearings, wheels, bushings, gears, and pulleys

Three-jaw construction ensures equal load distribution, secure hold, and concentric pulling action

Forged steel jaws for increased strength over investment casting

With OTC's 522 Large Gear and Pulley Puller you can easily remove a wide range of gears, pulleys or other parts that have tapped holes

Spread from 2 inches to 7-3/4 inches; block is 8-1/4 inches wide

Forcing screw is 3/4 inch-16 x 11-5/8 inches long

Rear-axle bearing puller set for use with most domestic cars

Removes semi-floating rear axles

Includes 3 pullers for greater versatility

Separator tools are used with bar puller and legs for a wide variety of pulling jobs

Includes the two most popular bearing splitters - 2 inch and 3 inch - plus four sets of hex push puller legs

5 inch bar-type puller head with forcing screw

1 Year Warranty

For Use in Differential Applications

Designed for Specific Applications

For removal of the front hub assembly; necessary for wheel bearing or brake rotor service

Provides the mechanical advantage and straight pull not possible with a slide hammer; for 4WD vehicles

Services 1988-2013 GM 1/2-ton, 3/4-ton, and 1-ton trucks, Tahoe, Suburban, and Yukon

WHEEL BEARING PULLER SET: This wheel bearing tool kit by Orion Motor Tech provides everything you need to let you quickly and easily remove and install your wheel bearings without hammering and front-end alignment

UNIVERSAL COMPATIBILITY: Our versatile wheel bearing press kit offers multiple sleeves and bushings in most common sizes to work with nearly any front wheel drive automobile or light truck, whether foreign or domestic

QUICK & EASY OPERATION: Two 8.8 grade sliding screws with precision threading firmly hold your bearings and let you smoothly pop them out without damage, leaving the steering knuckle and strut assembly untouched

Great Compatibility: The clamshell carrier bearing puller is compatible with Dana 30, 40, 60, 70, Ford 10.25" bearings. With the clamshell bearing puller, you can quickly remove the bearings. In addition, its power is evenly distributed, so less damage will be brought to your pinion bearings.

Premium Performance & Features: With high working efficiency, this carrier pinion bearing puller can effortlessly remove the pinion bearings with minor damage, drastically reducing dismantled time. And the carrier bearing puller will no longer easily pry into the pinion's sealing surface.

Complete Equipment: All necessary parts are ready for you. There is a main puller body, plug, center bolt, 3 clamshells, retaining ring, and adjuster rings. Besides, this unit comes with a handy stand, so you can group all the working parts together.

VERSATILE PULLER SET: The Orion Motor Tech 9-Way Slide Hammer Puller Set with 4 lb slide hammer is ideal for a variety of pulling applications, including flange-type rear axles, most front-wheel-drive hubs, pulling dents, and other press-fit parts (bearings, bushings, gears, pulleys, etc.).

INTERNAL & EXTERNAL JAWS: Includes 2-jaw and 3-jaw pullers for internal and external work to provide a variety of combinations to pull bearing, gears, and seals. 2 and 3-way cross blocks and cone-type puller provide the perfect jaw configuration for most jobs.

ULTIMATE DURABILITY: Built to last with rugged carbon steel alloy and chrome vanadium steel components, our tool kit can withstand accidental drops and years of heavy use without cracking or rusting.

Push puller is the best pulling choice when threaded holes are not available

Great solution for many applications like: heavy-duty pinion bearings, side bearings, alternators, generators, power steering and crankshaft pulleys, timing gears, harmonic balancers, and more

Features a classic 'H Bar' style puller block accommodating a 7 inch to 11 inch application spread

EASY TO USE: Slide flat end of puller through center of bearing and flat against backside of bearing, then slide washer down the center of the shaft against front side of bearing and tighten the nut on smaller end of puller, then thread a slide hammer (not included) to the puller and slide hammer back and forth until the bearing comes out; The washer captures the bearing firmly to distribute the applied force over the entire bearing and prevent damage

Use the VCT Pneumatic SAE Standard Rear Axle Bearing Puller 3-Piece Service Set – Domestic Car Vehicle Bearings Removal Tool Kit to service semi-floating rear axle bearings on your vehicle; These tools make the job simple and prevent damage to your bearings when pulling; Much easier than claw-type axle bearing pullers that slip off and chew up the old bearings; For removal only, not intended for installation

FITS YOUR CAR: Standard SAE sizes work for most American domestic makes and models; Set includes the following sizes to fit main bearing tube – 1 inch to 1-7/8 inches, 1-5/16 inches to 2-3/8 inches, and 1-3/8 inches to 2-7/8 inches; Sizes permanently laser-etched on tool for easy identification; Each tool fits a basic slide hammer with a 5/8-inch x 18 thread pitch

Services cars and light trucks 3/4 ton

Can be used for other applications such as bearing, collar, and gear removal

Features forged adjustable jaws and two clamp bolts that lock jaws together

WHEEL BEARING PULLER SET: This wheel bearing tool kit by Orion Motor Tech provides everything you need—pullers, installers, bolts, plates, & dowels—to let you quickly and easily remove and install your hog's 3/4", 1", or 25 mm sealed wheel bearings

COMPATIBLE WITH HARLEYS: This wheel bearing puller tool kit is compatible with most Harley-Davidson motorcycles since 2000, including Twin Cam, Sportster, VRSC models, and more

QUICK & EASY OPERATION: The unique design of these motorcycle tools firmly hold your bearings and let you smoothly pop them out without damage, leaving the wheels untouched

[APPLICATION]: This rear axle bearing puller can help to pull out semi-floating rear axle bearings quickly and effectively.

[EASY TO USE]: The washer of the axle bearing puller can captures the bearing firmly to distribute the force to the whole bearing, can avoid damage of the bearings and case.

[DURABLE MATERIAL]: The rear axle bearing removal tool is constructed from heavy duty cast steel, which has good strength and durability, can provide long service life.

For a wide range of pulling jobs including: bearings; alternator, generator, power steering, and crankshaft pulleys; timing gears; harmonic balancers; and more

Drop-forged components can be used in a variety of combinations

Set components deliver a spread of 3 inches to 5 inches and a reach of 1 inch to 2-1/4 inches

DAMAGE-FREE REMOVAL: This Mofeez 3 jaw puller removal tool makes removal side gear puller, sprocket puller, bearing puller, pulley puller, flywheel puller and more simple and damage-free. It can be worked with your wrench, ratchet, or spanner.

BUILT TO LAST: All parts are made with premium carbon steel for maximum strength. The jaws are galvanized to provide superior corrosion resistance and long service life.

3 OR 6 POSITION DESIGN: The universal and reversible jaws offer versatile inside or outside grip along with short or long reach; The 3-inch and 4-inch gear puller has 3 positions and the 6-inch gear pullers have 6 positions.

1.16-PIECE SET: This blind bearing puller set by Orion Motor Tech includes a slide hammer, counterstay puller, spare pin bolt, 3 screw adapters, and 10 split collets to get all your work done on parts from 1/4 to 2-1/3 inch diameter (6-59 mm)

2.HEAVY-DUTY CONSTRUCTION: These wheel bearing removal tools are made from AISI 1045 medium carbon steel forged and galvanized for long-term durability under even punishing use; the collets in particular are chromoly steel to handle even the most stubborn blind bearings and bushings without trouble

3.WIDE APPLICATION: This internal bearing puller set's expandable collets and threaded screw adapters remove tight and jammed axles, bearings, and bushings on a wide variety of vehicles without damaging the removed parts

16-PIECE SET: This blind bearing puller set by Orion Motor Tech includes a slide hammer, counterstay puller, spare pin bolt, 3 screw adapters, and 10 split collets to get all your work done on parts from 1/4 to 2-1/3 inch diameter (6-59 mm)

HEAVY-DUTY CONSTRUCTION: These wheel bearing removal tools are made from AISI 1045 medium carbon steel forged and galvanized for long-term durability under even punishing use; the collets in particular are chromoly steel to handle even the most stubborn blind bearings and bushings without trouble

WIDE APPLICATION: This internal bearing puller set's expandable collets and threaded screw adapters remove tight and jammed axles, bearings, and bushings on a wide variety of vehicles without damaging the removed parts

Can be adjusted by legs to an 8 inch diameter bolt circle.Fit Type: Vehicle Specific

Made of alloy steel and drop forged

Heavy duty tool has a center screw with a 1-1/8 inch hex head

【VERSATILE】Will help users easily install race seals without damaging the race or axle housing

【INCLUDING】 9 collar/disc sizes: 1.565", 1.750", 1.965", 2.325", 2.470", 2.555", 2.830", 2.995" and 3.180" along with driver handle 5-1/2”

【MATERIAL】Constructed form high strength aluminum for extra durability and strength

Set Includes: the package comes with 9 pieces of keyboard lube switch puller tools, including IC extractor, switch puller, key cap puller, elbow tweezers, pointed tweezers, 2 pieces flat head grease brush and 2 pieces fine head grease brush, bringing your life with more convenience

Clean set: by using key cover uninstall in the suite, you can easily remove all the keyboards, then you can easily clean the keyboard; When you need to customize the keyboard, switch board can help you easily switch, we also provide different sizes of grease brushes to help you clean the keyboard regularly

Practical life tools: as for keyboard and electronics enthusiasts, the IC chip remover tools are an essential tool set to provide more convenient help; The stem holder in this package is a 4-forked tool clamp that clamps the stem and picks up any small part (such as spring or IC), and the switch extractor can be applied as IC extractor or chip extractor, which can be a good gift for electronics lovers

【POWERFUL TOOL】 : This Hydraulic Gear Puller has 10 Ton Max Capacity and 2"(50mm) Ares Travel with spread10" ( 250mm) which can meet your working requirements

【3 IN 1 DESIGN】:This Wheel Bearing Pulling Separator integrates pumps, oil tube and drawing machine. Its forged steel 2 way yoke allows twin or triple leg pulls, the 3 jaw types can be adjusted from high to low point. Pump head can be turned by 360°for flexibility

【COMPACT & LIGHTWEIGHT】: The integral puller is compact and lightweight, Packed in blow mould carrying case, easy for you to transport or storage