Best Spurick in 2026

Lower Unit Gear Lube Drain and Fill Hole Screw and Seal 79953Q04. Used with 3/8 - 16 drain/fill hole screw on all MerCruiser stern drives, Mercury and Mariner outboards.

This is the non-magnetic plug screw version. Helps prevent gear lube from leaking out and water from seeping in to the gear case causing serious damage.

18-2244 Drain Screw for Mercury and Mercruiser. This Drain Screw is for use with the following: for Mercruiser I, R, MR, Alpha One, TR, TRS & all O/Bs with 3/8-16 non-magnetic gear lube fill or vent screws.

Feature：100% brand new and suitable.Made of high-quality nylon material, anti-wear and anti-corrosion,would not break or crack easily during use.

Cover Diameter: 18mm ≈ 0.7in. Stem Length: 20mm ≈ 0.8in. Fills Holes: 6-7mm ≈ .25in. Fitment: Compatible with most German cars, Japanese cars and American cars

You can use these to plug two bumper holes from removing front license plate which does not require both front and back. Used a 1/4 inch drill bit to make the two holes slightly larger for these plugs to fit perfectly.

ALL APPLICABLE: This license plate bolts set of fasteners includes 4 black license plate screws. Fits for Most Domestic Cars and Trucks including Chrysler, Dodge, Jeep, Ford, GMC, Cadillac, Buick, and Chevrolet vehicles.

EASY INSTALLATION: This licence plate screw set is easy to use and can be easily installed with an ordinary screwdriver, no special tools are required.

RUSTPROOF: Our license plate screws are made of high-quality non-rusting materials and covered with black insulating material, which can effectively prevent rusting and not damage the car.

Needed these for your mercury mercruiser outboard. Fit perfect and are magnetic, so metal fillings within the lower unit will stick to them for the nest flushing and refill.

Lower Unit Gear Lube Drain and Fill Hole Screw and Seal 8M0058389 is used with 3/8 - 16 drain/fill hole screw on all MerCruiser stern drives, Mercury and Mariner outboards except the Verado series.

It is very important to use the seal to make sure the drain/fill hole screw seats properly to retain the gear lube in the gear case and keep damage causing water out of the gear case.

Universal fuel filter can be used for tractors, riding mowers, cars, trucks, GF61 motorcycles, generator, boat, RV's, and for kubota diesel mower and any gas power engine.

Fuel filter fits 3/8"fuel line - 3/8" joint or connector at each end, orange inner filter with metal brass end caps on the top and bottom of the filter.

You can put this on the fuel lines of your backhoe and tractors to protect tractors or backhoe fuel injectors from dust.

SUITABLE FOR 1/4" & 5/16" - Inline Gas Fuel Filter for 6mm & 8mm 1/4" & 5/16" internal diameter pipe. These gas tapper filters are barbed, so there is no slippage from the fuel line. Easy to install and have no problems with leaking issues.

EASY TO SEE INSIDE - With this type of filter you can see if the filter is dirty and the debris that it has kept out of your gas line & carb. Installs easily and quickly. Do yourself a favor and swap out your old filter for one of these and replace it every couple of years.

CLEAN THE FUEL - If you don't use them already, these inexpensive filters are invaluable in keeping the debris that will get into your small engine fuel tank from getting to the carb. These will stop that crud from getting into the carb.

Perfect For The Marine Environment: Our marine drain screw gaskets are the ideal solution for outdrive drain, vent plug / vent screw and oil level use. Compatible with most lower units and seawater pumps. Keep oil in and water out with the tight seal created by these gaskets.

Made of high quality material with asbestos free, prevent gear oil leaking. For use on the 3/8-16 drain/fill screw holes in outboard and stern drive gearcases.

Compatible with inboard / outboard motors made by a variety of manufacturers. Used With The 3/8-16 Drain/Fill Screw Found On All Mercruiser And Most Mercury/Mariner Tohatsu Mallory Johnson Evinrude Outboards.

699056 replacement part number:699056, 490-404, compatibles with BS MODELS : 122H02 122K02. 790849 replacement part number:790849, this is the spring that goes from the choke arm above carburetor.

Just what you needed to fix the choke on your mower. After installing this to replace the missing air vane spring, Your mower starts easily with one pull.

This spring is for Briggs & Stratton and is very easy to install. This spring closes the throttle plate when the engine is cold. Use this to repair your auto choke for Troy-bilt Craftsman Toro Recycler Brute Lawnmower with a BS series motor.

A bolt used to secure the engine oil pan drain plug access cover to its mounting point. a clip which helps secure the skid plate to it's mounting point.

A Clip Used To Align The Radiator Support Splash Shield And It's Mounting Point. Radiator Support Splash Shield Bolt .

The specialty screws were a direct fit for your Honda CRV Civic Accord. The screws were used for undercarriage skid plate or oil pan slidplate.

WORKS ON MOST GENERATOR THAT HAVE 3/16" GAS LINE - Works good on your honda Sportsman generator fuel line. this size line also would work on your Champion generator. Fuel line will hold up fine and works great on your Generator from the fuel tank to the carb.

GREAT FUEL LINE FOR SMALL ENGINES - For gas, diesel etc. fuel hose lines, vapor emission lines and vacuum smog control. Please note it's a non-pressure fuel line, not for engines with fuel pumps.

LAWNMOWERS / RIDING MOWER FUEL LINE - For use in mowers tractors snow blowers dirt bikes pit bikes tao tao and just about all small engines. Works perfectly to replace the cracked and leaking line on your generator.

WORKS ON MOST MOWERS THAT HAVE 5/16" GAS LINE - The parts work fine in replacing the whole fuel line on your old lawn tractor. You can use a little soapy water on the tubing to push it onto the filter and onto the gas tank. Make sure the little metal spring clips are on the tubing a little further down than the length of filter ends. It makes it a lot easier to put on that way and the soapy water allows the tubing to slip on smoothly.

GREAT FUEL LINE FOR SMALL ENGINES - The correct OD is so much easier to install on a small engine than the larger diameter automotive fuel line. There is enough to do two to three engines (or more) depending on the length of run(s) required. This tubing fit your current small engine repair requirement and will be perfect for planned future upgrades and repairs.

LAWNMOWERS / RIDING MOWER FUEL LINE - Good Quality 5/16 Inch Gas Line Hose for your Lawnmowers. Just the right amount of 5/16 inch hose you needed to replace Factory Fuel Lines on push mower and riding mower. This is Quality Goodyear Hose Made in the USA unlike the crap that was deteriorating from the lawnmower manufacturers.

WORKS ON MOST MOWERS THAT HAVE 1/4" GAS LINE - The parts work fine in replacing the whole fuel line on your old lawn tractor. You can use a little soapy water on the tubing to push it onto the filter and onto the gas tank. Make sure the little metal spring clips are on the tubing a little further down than the lenght of filter ends. It makes it alot easier to put on that way and the soapy water alows the tubing to slip on smoothly.

GREAT FUEL LINE FOR SMALL ENGINES - The correct OD is so much easier to install on a small engine than the larger diameter automotive fuel line. There is is enough to do two to three engines (or more) depending on the length of run(s) required. This tubing fit your current small engine repair requirement and will be perfect for planned future upgrades and repairs.

LAWNMOWERS / RIDING MOWER FUEL LINE - Good Quality 1/4 Inch Gas Line Hose for your Lawnmowers. Just the right amount of 1/4 inch hose you needed to replace Factory Fuel Lines on push mower and riding mower. This is Quality Goodyear Hose Made in the USA unlike the crap that was deteriorating from the lawnmower manufacturers.

It is an exact replacement for your Husqvarna rider and Craftsman LT1000 LT1500 LT2000 riding mower. Remove the old switch, install the new, reconnect the wiring plug and done.

Ignition Starter Switch Suitable for: AYP: 193350; for CRAFTSMAN :193350; for POULAN: 193350; for MPN: 193350; for HUSQVARNA: 532193350; for DELTA: 6900-49P1. MODELS: LT / LTS / YT / ST / GT.

Replace the old, failed Ignition switch, solve problems like unable to start lawn tractor. 4 position: mow-in-reverse type - 7 terminals. Easy install on your Husqvarna rider and Craftsman Riding Mower.

Made of high quality material with rubber coated, prevent gear oil leaking. For use on the 3/8-16 drain/fill screw holes in outboard and stern drive gearcases.

Gearcase gear lube drain screw washer 830749 is rubber coated stainless steel that fits for Mercury and Mariner outboards and all MerCruiser stern drives with 3/8-16 gearcase drain/fill screw holes.

Always double check to make sure the washer has been secured when reinstalling the drain screw. Water could infiltrate the gearcase without it and cause catastrophic damage to the gearcase.

【HIGH-QUALITY MATERIALS】: Stainless steel surf fin screw will not rust in fresh or salty water; Besides, the rubber o-ring and acts as a 'spring' to insure the screw has pressure on it and can tighten it down without scratching the board.

【EASY TO USE】: Hand tighten against rubber o-ring means no tools required, do not need a screwdriver to install, adjust, or remove your longboard fin or stand up paddle board fin; No more tools get you out on the water faster.

【PROTECT YOUR SURFBOARD】: Up until now someone had always used screws to hold in longboard fins and was forever frustrated with screwdrivers jumping and scratching fins/boards etc. Those days are over. These fin screws will definitely protect your sup or paddleboard.

Feature：100% brand new and suitable.Made of high-quality nylon material, anti-wear and anti-corrosion,would not break or crack easily during use.

Cover Diameter: 18mm ≈ 0.7in. Stem Length: 20mm ≈ 0.8in. Fills Holes: 6-7mm ≈ .25in. Fitment: Compatible with most German cars, Japanese cars and American cars

You can use these to plug two bumper holes from removing front license plate which does not require both front and back. Used a 1/4 inch drill bit to make the two holes slightly larger for these plugs to fit perfectly.

The billet fuel drain valve is the perfect replacement for the OEM drain valve. The upgraded proprietary nitrile washer was designed to replace the cheap OEM rubber washer which can swell, deform, and sometimes become brittle.

A beefier, stronger fix for the problematic OEM drain valve. Billet Fuel Drain Valve For 2017-2022 Ford Powerstroke 6.7L - Replaces HC3Z-9J305-A.

Upgraded proprietary nitrile flat washer replaces the cheap OEM rubber washer on the tip. Increased surface area for easier gripping & removal.

Easier than painting, protects tow straps. Install both in 30 seconds for better aesthetics and protection of the tow strap end during a recovery event. Add a cushioned grip to your tow strap recovery while also providing an attractive custom look to your front bumper.

You will be pleasantly surprise how easily these go on and grip onto the hooks. Made of high quality rubber and ensuring that your tow hook covers will last for years to come. This truly enhances the front end appeal of your Jeep while providing grip on towing situations.

Cool addition to your 4XE, JK, JL, TJ, gladiator JT to protect the painted hooks and keep that color pop. Great product, just what you are looking by for to avoid painting your tow hooks!

Compatible with many 50cc 70cc 80cc 79cc 90cc 97cc 110cc 125cc 150cc 159cc 196cc Mini bike, Dirt bike, Pit bike, Generator, Lawn Mower, Tao tao, Pocket Motocycle, Scooter, Moped, Quad, ATV and Go Karts.

Fits in 3/16 id rubber fuel line with a 1/4 od fuel line inlet and out let. For some Honda Ryobi etc. generators. Install this into your fuel line to turn on/off your generator.

Works perfectly with various lawn mowers like John Deere craftsman harbor freight zero turn mower. They will hold up good and keep the gas from getting leaking.

Cast Brass Pipe Plug, 1/2" NPT solid brass Drain Plugs. These are made to stopper drain holes on boat transoms. It fits a standard transom drain hole. Check the size of your transom hole.

Precision thread and solid brass, more durable, ductility at high temperatures, and low magnetic permeability, not hollow like many poor quality plugs that rot and sink boats.

This item for sale is a brand new 2-Pack of 1/2" NPT solid brass Drain Plugs commonly used in boat hulls. High quality and deep threads allow the fittings to bite better, tight threads, not easy to slip.

These fuel filters are the exact replacement for factory filters on your Cub Cadet ZTR XT2 ZT1 ZT3 ZTX5 ZTX6 Z-Force zero-turn mower with the Kawasaki engine.

Fitment: For Kawasaki FR541V FR600V FR651V FR691V FR730V FS481V FS541V FS600V FS651V FS691V FS730V FT651V FT730V FX481V FX541V FX600V FX651V FX691V FX730V FX751V FX801V FX850V FX921V FXT00V.

This is the correct fuel filter for Kawasaki motor on a Husqvana zero turn lawnmower. Perfect match for Kawasaki / Scag commercial mower. Fits All 730V & 850V EFI Engines, Optional on Other Carbureted Models.

This type of switch does not require a separate push button to engage the starter it instead works the same as your car does. It has four terminals on the back. One goes straight to battery, another goes to starter solenoid, third is an accessary terminal for lights or other 12v units.

No more turning the key and pressing a button to start the car, It's all done at the key like on newer cars! Good current strength too. Works well on a 6 volt car, and I'm sure it works the same on 12 volt systems. This switch doesn't care if your car uses a positive or negative ground system.

Notes: the momentary starter position (middle terminal post) disconnects the ACC (accessory) post to protect the radio while starting the engine. ACC stays on when in the IGN position. Clockwise key positions are (ACC, OFF, IGN, START).

Air filter replace generac guardian air filter 0D9723 0D9723S. Fuel filter replace generac generator 0D6313.

Fits most generac V-Twin 760/990 cc engines all 12.5 - 17.5 KW generac XG, XP, & ultra source gens generator.

Compatible with most universal RV generac generator.

Cutoff Valve compatible with many small engines riding lawn mower, power washer, garden tractor, pressure washer, snow blower, generator, push mower, leaf blower, ATV, motorcycle and more with 1/4" inner diameter fuel lines.

Replacement shutoff valve for wide range of John Deere, for kawasaki, for kohler, for craftsman, for poulan, for toro zero turn, for snapper zero turn, for husqvarna, for briggs stratton, for cub cadet and other machine engines.

Straight fuel cut-off and shut-off valve, fit for 1/4-inch fuel line; Package includes 4 pieces fuel shut-off valve, plus 8 pieces spring clamps.

Fitment - Fit for Jeep TJ 1997-2022, for 2007 2008 2009 2010 2011 2012 2013 2014 2015 2016 2017 2018 Wrangler TJ JK JKU JL, for 2019 2020 2021 2022 Gladiator Rubicon, for Cherokee XJ.

Function - During the off-road process, the Floor Pan Drain Plug can effectively prevent water, dirt and sand from entering the floor of the car, keeping the floor clean and dry at all times.

Easy to install - Plug and play, if there is water in the car floor, the plug can be quickly pulled out and the water can be drained out of the car. These oval plugs are a perfect and tight fit front and rear floor pans.

Perfect fit for Your Bearing Buddies - Use them on your bearing buddies. Fit perfectly and keep water and grease off your boat trailer wheels. Make sure you order the correct size bras for the bearing buddies you have and you’ll be happy.

Keeps Water and Dust Out of Bearing Races - Your boat trailer doesn't have dust caps on the bearing buddies. This is especially problematic for a boat trailer where the wheels go under water in launching the boat. You do not want water to enter the bearing. These covers keep water, sand and dirt out of the bearing buddy and stay on.

Soft and Pliable Bearing Protector - These are easy to put on your buddy bearings. They are soft and pliable not like the hard ones that originally come with the bearings that are hard to put on cause they are so stiff and wouldn't let enough air to pass to get them on all the way.

Fuel tank vent valve is designed to relieve pressure from your gas tank. This direct-fit replacements also prevent gas from spilling out of your tank in the event of an accident.

Fits Jeep Wrangler (YJ) (1987-1995), Jeep Cherokee (XJ) (1984-1996), Jeep Comanche (MJ) (1986-1992), Jeep Grand Cherokee (ZJ) (1993-1996).

Fits Dodge Ram Van (AB) (1994-1997), Dodge Neon (PL) (1995-1999), Dodge Stratus (JA) (1995-1996).

This carburetor gasket provides an air tight seal between the carburetor and the bowl. High quality gasket kit, providing good tight seal. We recommended to replace the gaskets when cleaning or rebuilding the carburetor float.

Carburetor Float Bowl Gasket Kit fits Honda GX240 GX270 GX340 GX390 GX420 engine on troy built power washer pressure washer.

Fits carburetor on your Honda GX240 GX270 GX340 GX390 GX420 engine. Allow you clean the carburetor and reassemble it with no leaks. Get you float bowl to quit leaking.

This carburetor gasket provides an air tight seal between the carburetor and the bowl. High quality gasket kit, providing good tight seal. We recommended to replace the gaskets when cleaning or rebuilding the carburetor float.

Carburetor Float Bowl Gasket Kit fits Honda G150 G200 GC190A GCV135A G300 GCV160 engine on troy built power washer pressure washer.

Fits carburetor on your Honda G150 G200 GC190A GCV135A G300 GCV160 engine. Allow you clean the carburetor and reassemble it with no leaks. Get you float bowl to quit leaking.

Perfect length for minibike with mikuni carb. You should put this on your Coleman 200 CT200U CT200EX BT200X after you upgraded the carb to a Mikuni slide style. Perfect length. It also fits the thumb throttle you put on the bike.

50 inch total length and the moving length is 4.7". For CT200U Mini Baja MB165 196cc 5.5hp MB200 200cc 6.5hp Pit Bike Heat Warrior MBX10 MBX11 Parts.

Perfect fit for Coleman 200 CT200U CT200EX BT200X mini-bike with mikuni style vm22 carb. Easy to install and works great without any modifications.