Best Taytools in 2026

100 Pack 10mm x 24mm x 50mm Beechwood Loose Tenons

Solid kiln-dried Beech hardwood for strength and durability

Compatible with slots cut by Domino loose tenon joinery system

Bench dogs are an essential hold down device that should be a part of any workbench. Bench dogs will greatly improve the function of any bench. They allow securing work to the edge or top of your bench by using 3/4 inch holes. Install wherever you want simply by drilling a ¾” diameter hole.

Come in packs of 2 each. Overall length is 2-1/4 inches.

These dogs are just under 3/4 inch by 0.015 inches so they won’t bind in the hole, yet the side spring holds them in place at any desired height.

Guaranteed straight to within 0.001” (that's one thousandth of an inch!) over the entire 24” length

Anodized aluminum .0400” (7/16”) thick by 1.750” (1 ¾”) wide

Reference edge is machined flat and smooth

Lot of 2 each 3/4” wide x 3/8” high x 48” long

Precision extruded aluminum

Thick .100” sidewalls minimize bowing and twisting

2 pack 3 inch C Clamps with 900 lbs clamping force

Power coated reinforced malleable steel jaws provide powerful and rigid clamping

Zinc plated carbon steel Acme screw turns smoothly and produces maximal clamping pressure with less effort. The screw end has a swivel pad to allow gripping of various shaped parts.

This is a piece of 5/16 inch thick x 5 inch x 12 inch float glass for use as a flat, hard surface in a the Scary Sharpening System

Float glass is dead flat and the perfect substrate to attach abrasive sheets

Piece will accommodate 1/2 sheet of 8-1/2 x 11 microfinishing or lapping film

This aluminum straight edge is an economical alternative to other much more expensive straight edges on the market. This straight edge is very helpful to determine machine table flatness and in setting up machines such as jointers and planers and various out feed tables.

. The straight edge is made from extruded aircraft aluminum and then the reference edge is machined flat to within 0.003" over the entire 50 inch length.

The easy-grip cross section is 7/16 inch thick and 1-3/4 inch wide. Finish is black anodized.

Bench dogs are an essential hold down device that should be a part of any workbench. Bench dogs will greatly improve the function of any bench. They allow securing work to the edge or top of your bench by using 3/4 inch holes. Install wherever you want simply by drilling a ¾” diameter hole.

Come in packs of 4 each. Overall length is 2-1/4 inches.

These dogs are just under 3/4 inch by 0.015 inches so they won’t bind in the hole, yet the side spring holds them in place at any desired height.

3/4” wide x 3/8” high x 36” long

Precision extruded aluminum

Thick .100” sidewalls minimize bowing and twisting

Lot of 4 each 3/4” wide x 3/8” high x 24” long T Track

Precision extruded aluminum

Thick .100” sidewalls minimize bowing and twisting

Squeeze both rubber grip ends to expand and release double wire hose clamp

Spring steel maintains pressure to hold hose securely in place

Double-Loop design has tighter grip on hose

25 pack

These slide-in T-nuts with a centered thread hole are a cost-effective fastening option for T-Track and other aluminum extrusions.

Specifications: Material: Unfinished carbon steel; Threads: 1/4-20; Length; 1.00 inch; Width: .443 inch; Thickness on sides and ends; .094 inch; Thickness in middle at threads: .130 inch.

This Micro Fine Chromium Oxide polishing compound is specially designed to be used with strops to put a scary sharp, polished, mirror-edge on knives, carving chisels and woodworking tools. It can be used on leather, wood or synthetic strops.

Bar weights in at 1.2 ounces and is 3/4 inches x 3/4 inches x 2-3/8 inches.

The waxy consistency allows it to adhere well to any substrate without powering. Simply rub the bar evenly on the surface like a crayon. A little goes a very long way, so this small bar will last for a very long time.

Set of 6 each 4" aluminum blast gates

Designed to fit 4" diameter hose or ducts

Direct air flow to exactly where you need it and maximize dust extraction by opening and closing select ducts

Set of 2 knobs

High temperature and impact resistant Phonelic construction

3 3/4" high x 1" in diameter

10 each star knobs

1/4 20 threaded through insert

2” diameter

3/4” wide x 3/8” high x 48” long

Precision extruded aluminum

Thick .100” sidewalls minimize bowing and twisting

Made from 3/8 inch thick precision straight extruded anodized aluminum that will not fluctuate when humidity changes

Fence faces are made from smooth melamine coated MDF and are adjusted by way of 4 rear mounted threaded knobs.

The outfeed fence face can be shimmed out either 1/32 inch or 1/16 inch by way of a brilliant shim system where 2 square aluminum bars are slid into one of 2 sets of offset tracks in the fence face

2 each 16 inch F style clamps with quick release clutch

Overall jaw height: 3-1/4 inches; Throat or usable jaw depth: 2-1/2 inches; Jaw width: 0.750 inches

Soft grip handle size: 3-1/2 inches long by 1 inch diameter; Screw travel: 1-1/4 inches; Thread diameter: 0.375 inches

2 each 36 inch F style clamps with maximum jaw opening of 36 inches

Overall jaw height: 3-1/4 inches; Throat or usable jaw depth: 2-1/2 inches; Jaw width: 0.750 inches

Soft grip handle size: 3-1/2 inches long by 1 inch diameter; Screw travel: 1-1/4 inches; Thread diameter: 0.375 inches

Measuring range 0 to 6.25 inches

Accurate to .001 inch per 6 inches

Resolution to 0.0005 inches

10 each star knobs

3/8 16 threaded post 2" long

2” diameter

Body and frog made from nearly indestructible ductile cast iron

Tote and knob are made from premium grade oiled and hand-rubbed Sapele

Iron is 0.120” thick and 2” wide and made from tool steel hardened and tempered to 55-60

Body and frog made from nearly indestructible ductile cast iron

Tote and knob are made from premium grade oiled and hand-rubbed Sapele

Iron is 0.120” thick and 2” wide and made from tool steel hardened and tempered to 55-60

Features quick-spring nut for Rapid and precise fine adjustment

Features brass fulcrum and adjustment mechanism

Made from high-grade carbon steel with Hardened and finely polished points

NOTE: Designed to work with Taytools T Track only

Set to desired measurement and make repetitive cuts without re-measuring each time

Stop flips up and out of the way when you need to make a cut in the middle of a piece

French 2-sided strop with 3” x 10” stropping surface

Used to put a wicked sharp edge on knives and other edge tools

Contains gold split suede leather on one side for use with stropping compound

Flat bottom curved spokeshave with dual fine blade adjustment mechanism. Sole is 1” wide.

Made from tough ductile cast iron

Adjustment knobs are solid brass and screws are stainless steel

Bench dogs have been used for centuries for numerous assembly tasks

Designed to be hammered into end grain to “pinch” boards together tight while glue dries

These have a square back for easy and straight driving and legs that are tapered in 2 directions