Best Wolf Tooth in 2026

Bling

Anodized

Made in USA

7075-T6 Aluminum

CNC Machined

Made in USA

Bling

Anodized

Made in USA

Strong resilient and non-marring DuPont  Delrin thermoplastic allowing for easy snap-on installation and full strength all the way down to -20°F/-29°C. | Shifts cargo to the bike: Small- and mid-sized saddle bags are ideal places to securely store tubes mini tools and CO2 cartridges ensuring that they’re always on hand when needed while freeing up the top tube and handlebar bags for more regularly accessed items. | Protects dropper post stanchion: Inexpensive insurance the Valais protects dropper post stanchions from the wear that occurs at the intersection of saddle bag seatpost and wheel-flung grit. | Emergency crutch: While dropper posts continue to improve locking mechanism failure still occurs- often far from the trailhead. The Valais can be used to keep posts extended allowing the rider to comfortably pedal out of the backcountry. | Raceday travel limiter: When seven inches is more than the terrain calls for the Valais can be used to limit dropper travel to suit. | 35mm tall |Valais limits the dropper travel by at least 25mm.|Must have an internal cable routing dropper post|Optimized for straps up to 1" (25mm) wide though will work with wider straps|There are two Valais sizes available: 25mm diameter stanchions and one for the 26mm stanchions. Measure your upper seatpost stanchion diameter to determine the correct size to use.|Valais 25mm accommodates posts with 24.75-25.25mm stanchion diameter. Some known posts of this size include:|Easton Haven|Giant Contact (internal routing)|RaceFace Turbine|RockShox Reverb Stealth|Specialized Command Post|9Point8 Fall Line|Bikeyoke Revive|Others|Valais 26mm accommodates posts with 26-26.5mm stanchion diameter. Some known posts of this size include:|Wolf Tooth Resolve|Thomson Covert|Fox Transfer|KS eTen|One-Up|Others|At full compression the Valais' deep skirt contacts the seal collar first and will not contact the seal lip (protecting delicate seals from damage). |Remove the screw and slide Valais over seatpost stanchion|Put the Valais at the highest position install the screw and tighten to 2-3 NM|Install your saddle bag with it as full as it will be on the trail.  |Let all the air out of your frame shock drop the post and compress the bike suspension all the way.|Assure there is adequate tire to saddle bag clearance. If there is not tire clearance raise the dropper and lower the Valais until there is adequate tire to saddle bag clearance.|Re-inflate your shock and be sure that the Valais is torqued to 2-3 Nm|Cockpit Accessories

1x Wolf Tooth Crank Plate for direct mounting (Sram) on bikes with BOOST frames (148 mm shaft)

Wolf Tooth Drop-Stop patent prevents chain exits

3 x Offset

Long Axis Mounting monoplato 26 teeth Wolf Tooth for cranks SRAM direct mount)

Only compatible with pedalieres GXP Long Shaft Long spindle 15.4 mm

Not compatible with short, short spindle, 6th offset Axle cranks

Wolf Tooth

Alloy Bashguard 104 BCD

Chainring Guard

Drop-Stop chainrings are designed for use with 1x9, 1x10, 1x11 and 1x12 drivetrains

Compatible with all 10-, 11-, and 12-speed chains, with the exception of Shimano 12-speed chains

Shimano 12-speed chains require the use of Wolf Tooth's Shimano 12-speed specific chainrings

Hand-bent hollow tubing

Fits any bike frame that has two standard bottle cage mounts with 64mm spacing

Easily bent back in to shape if damaged

Compatible with standard 22.2mm mountain bike handlebars

Includes Wolf Tooth plastic bar end plugs

132mm long and 32mm diameter

Long Axis Mounting monoplato 30 teeth Wolf Tooth for cranks SRAM direct mount)

Only compatible with pedalieres GXP Long Shaft Long spindle 15.4 mm

Not compatible with – Short Short spindle cranks

A leak-proof robust and low-maintenance mechanical actuation system | Easy cable detachment for service or shipping | A 40mm (1 5/8in) reduction of in-frame height when compared to Connectamajig-equipped Reverbs | Straightforward 15-minute installation | Reverb Stealth generation A2 and B1 compatibility | Wolf Tooth's low-profile high-traction lever | Easily installed upfront cable fixing | A large-diameter 21mm ball-bearing pivot | Our low-torque cable-kind clamp | A solidly-mounted rattle-free integrated cable adjuster | The industry-first breakaway axle pivot making the inevitable mishaps less (financially) painful |Compatible with Rockshox Reverb A2 and B Spec Stealth (internal) routing dropper posts.|NOT compatible with A1 or C1 spec Reverbs.  See below for figuring out if you have an A1.  C1 Reverbs will have "Reverb" will be marked in gold cursive at the top of the post.|NOT compatible with non-Stealth (externally routed hydraulic hose)|A2 Spec has no marking at the top of the stanchion and the speed adjuster knob is black (vs Silver for the A1)|B Spec has gold "Rockshox" written at the top of the stanchion|If you have large hands (size XL glove) we recommend the 22mm handlebar clamp so you have more flexibility to move the lever in.|See the picture carousel for a comparison of the ReMote IS-II vs ReMote LA IS-II (note that the Sustain system requires the use of a LA or Light Action lever)| ReMote IS-AB for Shimano works for some Hope Brakes.  See details here | Contact us for questions on other post compatibility.|ReMote IS-AB for Shimano I-Spec A or B - Includes IS-AB Hardware|ReMote IS-AB for Shimano works for some Hope Brakes.  See details here.|ReMote IS-II for Shimano I-Spec II - Includes IS-II Hardware |ReMote MM SRAM/Avid MatchMaker X  - Includes the MatchMakerX hardware which is a T-Nut and bolt that allows the ReMote MM to attach to the MatchMakerX clamp. You will need the MatchMakerX handlebar clamp which we do not sell but can easily be purchased.|ReMote 22.2mm - includes hinged handlebar clamp for 22.2mm handlebars (22.2mm is the standard diameter where your shift and brake levers attach). Attach with 1 NM max (it doesn't take much!). |Standard ReMote for cable actuated droppers|Other cockpit accessories|ReMote replacement parts 

Wolf Tooth

ReMote Sustain

Dropper Seatpost Remote

Mount type: 110 BCD Asymmetrical 4-Bolt

Teeth: 42t

Offset: Non-boost

Mount type:Direct Mount for Easton and Race Face Cinch

Teeth: 40t

Offset: Non-boost (Standard offset)

Mount type: 110 BCD Asymmetrical 4-Bolt

Teeth: 40t

Offset: Non-boost

Features Wolf Tooth's Drop-Stop tooth design for maximum chain retention

Drop-Stop chainrings are designed for use with 1x9, 1x10, 1x11 and 1x12 drivetrains

Compatible with all 10-, 11-, and 12-speed chains, with the exception of Shimano 12-speed chains

Wolf Tooth

Shimano Hyperglide+ Direct Mount Chainrings

Direct Mount Chainrings

Properly sized to fit 104 or 64 BCD chainring | Two sizes for ultimate protection: smaller 26-30t (132 mm diameter) and mid-sized 32t-34t (148 mm diameter).  |These are for use with 104 BCD chainrings or 64 BCD chainrings on 104 BCD cranksets|These are compatible with all triple 104 BCD cranksets and mount in the “big ring” position|They are compatible with double cranksets that have flat outfacing mounting tabs like XTR M980. However many 2x specific cranks like Shimano XT M785 have a profiled outer surface on the mounting tab so our bashring cannot be mounted on that non-flat surface.|These work great with the 104 BCD Elliptical 32t ring. They will work with the 34t as well but at the max diameter a few teeth will extend just beyond the bashring.|Chainring bolt requirements for this bashring 104 x 30t - 10mm bolts are required for use with the bashring.|Other 104 BCD sizes - you will need 8mm bolts (stock size that comes on 3x cranksets holding the middle and big rings on). Wolf Tooth does not make these.|When using with the 64 BCD you will need 6mm bolts to mount the bashring. Note: Orient the head of the bolt to the inside to provide clearance for the chain (bolts will go in backwards).

Wolf Tooth

ReMote Sustain

Dropper Seatpost Remote

Levers are Reverb Stealth series specific - A-series have no Rockshox marking below the head whereas B-series have gold Rockshox markings below the head

Engineered break-away pivot that allows the lever to break away from the pivot in the event of a crash

Cable Kind Clamp does not damage secured cables and features captive hardware

Material: CNC-machined

Diameter: 30.9mm, 31.6mm

Travel: 125mm, 160mm, 200mm

The ReMount is designed to work with cable-actuated dropper and shock remotes with pivots parallel to the handlebar center|We do not recommend the ReMount for RockShox Reverb remotes.|We do not recommend the ReMount for multi-chainring drivetrains (it sits where your front shifter does)|The ReMount mounts securely to all standard (22.2mm) mountain bike handlebars |The ReMount is designed to work with cable-actuated dropper and shock remotes with pivots parallel to the handlebar center|The ReMount MM mounts securely to all MatchMaker X (MMX) compatible SRAM and Avid brake levers|TheReMount MM can be mounted to the underside of top/left RockShox MMX hydraulic lockouts|SRAM's MatchMaker X T-nut and matching Torx screw (pictured in gallery) are required for mounting| The ReMount MM is available with genuine MatchMaker X hardware if needed | The ReMount IS-AB mounts securely to all Shimano I-Spec A and I-Spec B left brake levers |Not all provided hardware will be required for each standard | The ReMount IS-II mounts securely to all Shimano I-Spec II (11-speed generation) brake levers

Levers are Reverb Stealth series specific - A-series have no Rockshox marking below the head whereas B-series have gold Rockshox markings below the head

Engineered break-away pivot that allows the lever to break away from the pivot in the event of a crash

Cable Kind Clamp does not damage secured cables and features captive hardware

Levers are Reverb Stealth series specific - A-series have no Rockshox marking below the head whereas B-series have gold Rockshox markings below the head

Engineered break-away pivot that allows the lever to break away from the pivot in the event of a crash

Cable Kind Clamp does not damage secured cables and features captive hardware

Two Sizes: Large is 112mm x 106mm, Small is 105mm x 99mm

Three high precision, low-friction sealed bearings designed specifically for this pedal, with one igus bushing

Custom radial seal to protect internal hardware from water, dirt, and trail debris

Multi-size package: this package contains 7 different sizes, 1 mm, 2 mm, 3 mm, 5 mm, 10 mm, 15 mm, 20 mm, small size of spacer headset let you have a more precise height adjustment

Appearance and performance: automatic cutting, smooth edge, fit most of the road bicycles, delicate texture and durable to use

Material of bike handlebar spacer: woven carbon, nice look and good quality, light weight, good strength and well temperature resistance, good impact resistance

Add personality & style to your bike with this precision engineered and machined stem cap and spacer kit.

Kit includes: 3mm, 5mm, 10mm, & 15mm headset spacers Ultralight stem cap with an integrated 5mm spacer 4 matching aluminum water bottle cage bolts Black aluminum stem cap bolt

1 1/8" top (straight 1 1/8" or 1 1/2" to 1 1/8" taper) steerer tubes only