Best Yanyu in 2026

Marine Hinge Overall Length : 3"/76mm; Width :1.5"/38mm; Outer Hole Distance :2.4"/62 mm; Inner Hole Distance :1 "/ 25.4 mm; Single Sheet Thickness : 0.2"/5mm, 6 holes,

Marine cabinet hatch hinge, stainless steel 316 silica sol precision casting, stronger than forged hinge，resistant to seawater corrosion

100% pure hand polishing, 6 polishing procedures, and finally polished with cloth wheel, Beautiful surface

Boat Deck Cleat Overall length is 8" (200 mm). The horizontal and vertical distance are 2.86" (72.7 mm) and 1.3" (33 mm) from center to center between two holes.

Boat cleats made of 316 stainless steel, maximum corrosion resistance, higher hardness, moisture-resistant, acid and alkali resistant, anti-rust, gloss and bright surface, non toxic, etc.

Stainless steel 316 cleats are high polished surface for mirror-like appearance to match marine uses watercraft, boat, yacht, boat docks, decks, piers for tying up boats, kayaks, etc.

Bimini Top Cap Fitting Size: Each eye ends measured approx 1.25'' O.D, 1'' I.D, fits for 1'' O.D round tubing. One screw on each fitting measured M6. Pin: 1/4" bolt holes.

1’’Boat external eye end has shining polished looking and smooth touch.Perfect replacement for marine hardware and accessories, widely used for boating,bass boat,fishing boat, kayak, canoe, yacht,etc.

Bimini Top Cap Fitting Cast from marine grade stainless steel 316 .Seawater corrosion resistance. stainless steel 316 bimini top eye end is a perfect choice to replace your plastic, nylon or broken fittings.

Boat Strap T Hinge Size: approx.3.9" (L)x2.1"(W) /100MM*54MM .The thickness: 0.19" .Weight: 92g .The detail size refer to left picture.

Stainless steel 316 silica sol precision casting, resistant to seawater corrosion .Mirror polished Stainless Steel Boat Hinges are built to last and will stand up to the elements.

Mounting for home/marine boat/yacht door or window, locker, cabinet, deck, tool box and so on.

Bimini Top Eye End Cap Fitting 7/8''(22.6mm) internal diameter , fits for 7/8'' outside diameter round tubing. One screw on each fitting measured M6. Pin: 1/4" bolt holes.

Bimini Top Cap Fitting cast from marine grade stainless steel 316 .Seawater corrosion resistance. stainless steel 316 bimini top eye end is a perfect choice to replace your plastic, nylon or broken fittings.

Bimini Top Fitting external eye end has shining polished looking and smooth touch.Perfect replacement for marine hardware and accessories, widely used for boating,bass boat,fishing boat, kayak, canoe, yacht,etc.

The outer diameter of the GAS Deck Fill Tank tube is 1-1/2” (38.8mm)，ideal for use with 1-1/2” I.D. fill hose.The outside diameter of the flange is 3 inch(76mm). The center of the screw holes is 0.3 inch(8 mm) from the outer edge of the flange. The length of deck fill tube is 3.15"(80mm).

GAS Deck Fill/Filler is cast from marine grade stainless steel 316, resistant to seawater corrosion ;the surface is mirror polished,the surface is smooth and beautiful.Recess flush to deck for contemporary look.

GAS Deck Fill/Filler Silica sol precision casting, keyless design - lift built-in tab on cap and turn to open or close.The lid is attached to the body with a stainless steel chain to prevent the lid from being lost.

Flip Up Dock Cleat Size: Length of all: 6 inch (155 mm); Width: 2.1 inch(53.8 mm);Raised height: 1.8inch (45.9mm); Recessed height: 0.53 inch(13.5 mm);Bolt hole spacing 3.36 inch(85.5 mm) (center to center);

Deck Cleat Material:Dock Cleat and Free Fasteners are made of Marine grade 316 stainless steel, Excellent seawater corrosion resistance and durable.Rope cleat work for dock lines ,mooring and etc;

Multi Purpose:High polished surface for mirror-like appearance to match marine uses watercraft/boat/yacht,boat docks, decks, piers for tying up boats, kayaks, jet ski's,etc.Smooth edge avoids cutting of rope or foot injury;

Boat Deck Cleat Overall length is 6" (150mm). The horizontal and vertical distance are 2.28" (58 mm) and 1.1" (28 mm) from center to center between two holes.about 5.22 oz/148g (Per Boat Dock Cleat)

Boat cleats made of 316 stainless steel, maximum corrosion resistance, higher hardness, moisture-resistant, acid and alkali resistant, anti-rust, gloss and bright surface, non toxic, etc.

Stainless steel 316 cleats are high polished surface for mirror-like appearance to match marine uses watercraft, boat, yacht, boat docks, decks, piers for tying up boats, kayaks, etc.

Flush Mount Cleat Size: Length of all: 125mm / 5 inch ;Weight: 0.75 LB / 340g ,M6 bolt (Please see the left picture for detailed dimensions).

Pull Up Dock Cleat made of precision cast marine grade stainless steel 316 ,

The telescopic cleat is no sharp edges, and will not damage the rope.

Retractable Low-Profile Cleat: Length of all:6"(158 mm) ;Width:1.5"(38 mm);The distance between the two tubes is 2.3"(58mm) .(Please see the left picture for detailed size)

Pull Up Flush Mount Cleat made of marine grade stainless steel 316, mirror polished ,Smooth and beautiful , resistant to seawater corrosion

The pull up cleat with rubber drainage accessories , accommodates 1/4" drain pipes, and the inside of the deck can be kept dry; using 1.7mm thick rubber gaskets, the pull up cleats can be installed perfectly. There is no gap between the cleats and the deck, and no water seepage.

The outer diameter of the GAS Deck Fill Tank tube is 2" (51 mm),Ideal for use with 2" I.D. fill hose, and cap contains O-ring seal.The outside diameter of the flange is 3.1 inch(80 mm). The center of the screw holes is 0.3 inch(7 mm) from the outer edge of the flange. The length of deck fill tube is 3.1"(80 mm).

GAS Deck Fill/Filler is cast from marine grade stainless steel 316, resistant to seawater corrosion ;the surface is mirror polished,the surface is smooth and beautiful.Recess flush to deck for contemporary look.

The deck filler has been professionally tested for air tightness, and there will be no leakage of fuel or water. If the O-ring is used for too long, it will be damaged，we have prepared spare rubber rings, which can be replaced in time.With rubber gasket, it can be a better fit between the deck fill and the deck .

Boat door hinges stainless steel marine grade corrosion resistant, AISI: 316 Stainless Steel. Marine hinges stainless steel are 6 holes flush door hinges for boat, Rvs, etc.

Flush door hatch hinges stainless steel are heavy duty marine hinges with 0.2 thickness. Pack of two sets with stainless steel screws.

Boat door hinges flush hatch hardware ensure the door can be properly shut, high reliability, directly replace your worn or broken door hinge.

[EXCELLENT MATERIAL]:The heavy duty hinge use Stainless steel 316 with 100% polishing silica sol precision casting,rust-proof and corrosion-resistant under big waves.

[DURABLE]: Marine strap hinge open and close pretty smooth. you can use long time without rust. It made by Casting not stamping. solid and strong.

[MULTIPLE USES]:Widely used in various types of cabinet doors, closet doors, locker doors, boxes, wardrobes, etc.

New 316 Stainless Steel LOCKABLE HOLD DOWN CLAMP

Kit includes everything you need to replace a pontoon gate latch

Works on both left and right hinged pontoon gates

Fits 1, 1-1/8, and 1-1/4 inch square tube railing

Fits in 1 inch mounting hole

Include: 1 latch, 1 keeper, 2 keys, 1 pull tab.

For 0.00"-0.407" Door Thickness

Boat flush pull latch, flush-mount, recessed handle, and concealed hardware make the flush pull latches an attractive solution for marine hatches, compartments, or other custom enclosures.

Boat flush latches stainless steel, all hardware of the marine latch Included, screws, mounting plate, and lock plate. Pack of 2 sets.

Marine slam latches for boat made of 316 stainless steel for flush mounted 2 inch cut out. Flush pull hatch latch has simple pull-to-open and push-to-close functionality with corrosion-resistant construction to ensure a long life in demanding outdoor applications.

Pair SeaLux Marine Marine Grade corrosion-resistant hinges Stainless Steel 3" x 1.5" Door Hinge

these gleaming, polished Stainless Steel Door Hinges will prove an attractive addition wherever they're used

Constructed of stamped 304 stainless steel

Package Include: 2pcs boat door latches slam latch.

Cutout Size: diameter Hole; 2" , lock style: - No-Locking flush pull latches.

Specifications: cutting hole:Φ50mm/2“，Door thickness:0.04"-0.23”.

Universal sizing fits square frames of 1", 1-1/4", and 1-1/4" Operates on right or left hinged gates

Dimension: 8-1/2"x9-1/2"x5-1/2"

Includes mounting hardware for quick and easy installation

Boat 316 stainless steel lockable hold down clamp anti-rattle latch,solid and excellent polished finished

Boat Anti-Rattle Latch is made of stainless steel 316 casting,maximum corrosion resistance and durability in the saltwater environment

Boat locker cabinet hatch anti-rattle latch,lockable,the detail size refer to the left picture

This stainless steel latch is non locking, flush mounted and uses 2" cut out

It includes all hardware needed to install (screws, mounting plate, and lock plate)

It can be used on panels 12 to 17 mm (.47-.67 inches) thick.

【Material】Polished stainless steel Marine Grade 316 construction,withstand sea water corrosion,Mirror Polished Finished,for Longer service life.

【Solid Base】Sturdy flanged base for nicer fit and added strength.

【Advantages】Open ring design.good for universal cups,cans and mugs.Widely use on boat, game table, sofa, cars and so on

Marine strap door hinges stainless steel marine grade corrosion resistant, AISI: 316 Stainless Steel.

Boat stamped strap hinge stainless steel have a lovely polished finish making them ideal for both interior and exterior marine applications as cabin locker door hatch strap hinges..

Boat deck cabin strap hinge ensure the hatch door can be properly shut, high reliability, directly replace your worn or broken door hinge.

Marine shortside hinges are made of 316 stainless steel which provide maximum corrosion resistance for salt-water marine environments.

Marine flush door hatch hinges five holes hinge stainless steel have a lovely polished finish making them ideal for both interior and exterior marine applications.

Heavy duty boat marine flush hatch compartment hinge, which is common size 3 inch x 1-1/2 inch. Pack of two sets with screws.

Chrome plated zinc alloy

Dimensions for face plate 3" x 2-1/4"

Dimensions inside handle 1-7/8" x 1"

Innovative Transom Saver helps lessen stress on a boat’s transom when boat with an outboard motor is being trailered

Reliably supports the cantilevered engine during transport

Adjustable from 36 to 60 inches for the best fit and fullest support

Attractive flush-mount styling, a recessed handle, and concealed mounting hardware gives these latches an appealing look The flush profile and easy installation makes this latch perfect for hatches, livewells, electrical enclosures, and other compartments on your boat.

they are designed to fit in a standard 2" hole cutout

This latch is widely used by all the major boat and yacht manufacturers, bait well lids, hatches,center console doors, tackle units, and drawer units，electrical enclosures, and is great for new applications as well.

Package length: 23.876 cm

Package width: 15.24 cm

Package height: 5.334 cm

Pair of SeaLux Marine 316 Stainless Steel 180 degree flush mount 2-3/4" x 1-5/8" Hatch Hinges for boat, RV

SeaLux 180 degree hinges fit flush in your boat and fold back 180 degrees so that your hatch can lay flat in the open position. They are ideal for flats and fishing boats.

Constructed of stamped corrosion-resistant 316 stainless steel.