Best Karparts360 Parking Light Assemblies in 2026

Partsam (2 x Amber) side marker LED clearance lights, each light with 6 LEDs inside; 4" x 2" Rectangle. Built-in reflex reflector removes the need for a separate reflector. Snap-on, replaceable, durable lens with white base. Surface mount . 2-Wire design

DOT Approved. Function as front / Rear clearance Lights Lamps, side marker lights or identification light,Trailer Light etc. Universal for 12V vehicles like Pickups Truck Trailers SUV van Caravan and Boat Lorry Bus etc.

Features sonically sealed, waterproof lens and housing in a single unit; Two-wire design includes both lead wire and ground wire for mounting to all surfaces.

Partsam (Pack4) Square Trailer Clearance and Side Marker Light with Reflex Reflector - Amber

Features 2-wire, hard-wired design; The two-wire design includes the lead and ground wires to mount to any surface(Black is Ground and Yellow is Positive); Easy to install, has mounting bolt centered on the back.

Perfect replacement for trailer side marker; 2-4/5" L x 2" W x 1-1/8" D; Reflectorized lens; corrosion resistant; mount on stud; 2-wire; 3 LEDs

Package includes 30 pieces 3.8" Inch Led Trailer Lights 6LED (10Pcs Amber + 10Pcs Red + 10Pcs White); free screws and Foam tape bases are included. The foam tape bases are used to adhere to the back of the marker lights or to the surface to which the light is to be mounted, for waterproofing. Also you can use a little strong adhesive to be sure;

These small clearance lights needs to be hooked up to a 12v power source. Flux: 600Lumens (about 20 Lumens per lamp); less than 1 Watt per light; Light Size: 75mm x 20mm x 5mm (2.95" x 0.8" x 0.2"), Light Size with Black Base: 96mm x 20mm x 10mm (3.8" x 0.8" x 0.4") and center to center distance: 3-5/16" approx.; The wire length is about 6~7 inch, and you can put them in series with speaker wire to make them longer;

Partsam Led Lights function as marker lights, camper light, Decorate Light, under dash lights, walk way lights, Golf Cart Light, Interior Lights, trailer lights, truck lamps, clearance lights, runnling lights, side marker lights, front parking lights and so on; We also have customers asking whether they can be use as turn signal lights, brake lights or backup lights, they can, but they may be not that bright;

This square double face Pearl LED pedestal light is different form many of the pedestal lights on market, it comes with chrome bezel and visor, give you a outstanding look when driving on road; Work as Stop Turn Tail Park Brake and Side Marker Clearance Light; This light comes with clear lens,clear lens led lighting gives your truck a bright and clean look; Amber on one sides and red on the other side and amber side marker with Chrome Bezel and Visor;

High power pearl led lights are perfect for functional needs, great visibility and decoration. These double-faced square turn signal lights are a popular alternative to the factory incandescent style found on many truck fenders. We carry this light in many different styles, for plenty of choices. Our post-mounted LED lights are unmatched in quality and diversity. These durable LED lights have sonically sealed polycarbonate lenses and waterproof housings. operate within a 9-14.8 VDC;

Double Face Pearl Led Pedestal Lights: Red side serves 3 functions - stop, turn and tail light and Amber side serves 2 functions - parking and rear turn signal light; Built-in, amber side marker light with reflex reflector; 52 LED Super Bright Fender for each light (24 Amber LEDs &24 Red LEDs & 4 side marker Amber LEDs ); Heavy Duty Chrome Housing with Visor, Single Stud Mounting;

Package includes 20 pieces 3.8" Inch Led Trailer Marker Lights 6LED Amber Lens; free screws and Foam tape bases are included. The foam tape bases are used to adhere to the back of the marker lights or to the surface to which the amber light is to be mounted, for waterproofing. Also you can use a little strong adhesive to be sure;

These small thin clearance lights needs to be hooked up to a 12v power source. Flux: 600Lumens (about 20 Lumens per lamp); less than 1 Watt per light; Light Size: 75mm x 20mm x 5mm (2.95" x 0.8" x 0.2"), Light Size with Black Base: 96mm x 20mm x 10mm (3.8" x 0.8" x 0.4") and center to center distance: 3-5/16" approx.; The wire length is about 6~7 inch, and you can put them in series with speaker wire to make them longer;

Partsam Amber Led Lights function as marker lights, camper light, Decorate Light, under dash lights, walk way lights, Golf Cart Light, Interior Lights, trailer lights, truck lamps, clearance lights, runnling lights, side marker lights, front parking lights and so on; We also have customers asking whether they can be use as turn signal lights, they can, but they may be not that bright;

Partsam 2 Pieces Square Trailer Clearance and Side Marker Light with Reflex Reflector - Amber

AMBER (Orange) rectangle clearance or side marker lights.

2-4/5" L x 2" W x 1-1/8" D; Reflectorized lens; corrosion resistant; mount on stud; 2-wire; 3 LEDs

Package includes 10 pieces 3.8 Inch Amber Led Trailer Marker Lights 6LED; free screws and Foam tape bases are included. The foam tape bases are used to adhere to the back of the amber marker lights or to the surface to which the amber light is to be mounted, for waterproofing. Also you can use a little strong adhesive to be sure;

These small thin clearance lights need to be hooked up to a 12v power source. Flux: 600Lumens (about 20 Lumens per lamp); less than 1 Watt per light; Light Size: 75mm x 20mm x 5mm (2.95" x 0.8" x 0.2"), Light Size with Black Base: 96mm x 20mm x 10mm (3.8" x 0.8" x 0.4") and center to center distance: 3-5/16" approx.; The wire length is about 6~7 inch, and you can put them in series with speaker wire to make them longer;

Partsam Amber Led Lights function as marker lights, clearance lights, runnling lights, side marker lights, front parking lights, indicator lights, identification lights, boat interior lights, camper light, Decorate Light, under dash lights, walk way lights, Golf Cart Light, Interior Lights, trailer lights, truck lamps and so on; We also have customers asking whether they can be use as turn signal lights, they can, but they may be not that bright;

Package includes 1 set LED Tail Lights Assembly Kit, compatible with 1976-1983 CJ5 tail lights, 1976-1986 CJ7 tail lights, 1981-1985 CJ8 tail lights, 1987-1995 Wrangler YJ tail lights and 1997-2006 Wrangler TJ tail lights. Driver Side and Passenger Side are included. Come and replace your dim factory tail lights with our brilliant LED tail lights assemblies and get eye-catching;

This rear combination tail lights kit feature 12 large brake, parking and directional LED's, 6 license plate light LED's, 21 brilliant white Back-Up LED's and 3 side reflector light LED's;

Partsam LED lights are a direct replacement for your stock tail lights. These rear LED lights are completely compatible with your electrical system, and the wiring tips are as below: White is ground, blue wire is for backup reverse light, black wire is for tail/license plate light/side marker light and red wire is for stop turn brake light;

Partsam Sealed 6" x 2" Amber Side Marker Light 13 Led Rectangle / Rectangular Light Surface Mount w/reflector

2" X 6" Unique Reflector Design; 11 LEDs facing straight ahead & 1 LED on either end, shining out the side; hole-to-hole distance:4.8"(approx);

6x2 Trailer-Style Rectangular LED Marker/Turn Signal Lights; The multi-faceted reflector creates the illusion of hundreds of tiny diodes sparkling behind the lens.

Partsam's High Quality Thin-design Smoke Black Lens Amber LED Led Marker Light, Stylish & Functional as side marker lights, clearance lights, indicator lights, identificaiton lights, utility lights etc.;

DC12V Each Light with High Quality 6 LEDs; Waterproof + Shock Proof + Viberation + Dust Proof; Brightness: 120 lumen each light with 6 pcs High Quality SMD LED 50,000hrs life span.

Two-wire design includes both lead wire and ground wire for mounting to all surfaces; The Black Wire is Negative/Ground. Light Dimension: 9.6cm x 2cm x 1cm (3.8" x 0.8" x 0.4") approx. Distance between center-to-center holes: 8.2cm (3.2") approx. Easy to Install with FREE Screw set included & Foam tape base.

Package includes 2 Pieces 2x6 inch Amber Rectangular Trailer Marker Led Lights 3 Wires Surface Mount, 21 Led diodes per amber light; Designed at 12 DC Volts; Sealed amber led Light, 3 Wires Setup, High Low Function. Other accessories are not included;

Compared with those similar side marker lights on market which can be used as led marker light only, this 6 inch rectangle LED lamp is a 3-WIRE assembly, meaning it can be used as both a turn signal AND a marker lamp simultaneously. It can also be used as only a marker lamp (or only a turn signal) by using two wires and leaving the third wire unused. These are a really popular style thanks to their multi-faceted design;

Size: 6" x 2" x 1.4" approx. and hole to hole distance: 4.8". Dim Function draws 20 mA & Bright Function draws 110 mA approx.. This trailer clearance light is unversal for almost all 12V vehicles as well as the size fits;

Partsam's High Quality Thin-design Smoke Black Lens Amber LED Led Marker Light, Stylish & Functional as side marker lights, clearance lights, indicator lights, identificaiton lights, utility lights etc.;

DC12V Each Light with High Quality 6 LEDs; Waterproof + Shock Proof + Viberation + Dust Proof; Brightness: 120 lumen each light with 6 pcs High Quality SMD LED 50,000hrs life span.

HARDWIRED WITH 2 WIRES and both lead wire and ground wire for mounting to all surfaces; The Black Wire is Negative/Ground and Yellow wire for positive. Light Dimension: 9.6cm x 2cm x 1cm (3.8" x 0.8" x 0.4") approx. Distance between center-to-center holes: 8.2cm (3.2") approx. Easy to Install with FREE Screw set included & Foam tape base.

Package includes 2 Pieces 11 LED 15" Ultra Slim Led Turn Signal Light Bar, CLEAR LENS AND AMBER WHEN LIT. This surface mount light bar is perfect for horizontal mount or vertical mount;

This 15 inch LED Trailer Turn Signal Light Bar is hardwired with 3 wires: White is the ground, red is high brightness for turn signal light and black is low brightness for tail light, parking light, clearance light or running light; NOTE: If you want to use it as strobe light, please buy a strobe module and connect,thanks;

Overall dimensions: Overall length is 15.5 inches approx.,overall width is about 1.3 inches, and the mounting holes approximately 14.5" Apart. The amber strip light bar is about half an inch thick, but with the little knob where the wires all come out, it's about 1 inch, so you may need to cut out a hole to allow that to go in. The spot knob is about half an inch in diameter. Really a nice slim low profile Waterproof LED trailer light bar;

Round red/Amber light serves as brake light, turn signal, and tail light: Outer Ring of LEDs comes with dual modes(high low Beam) and function as tail brake lights; Center Clear/Amber LEDs act as turn signal and Parking light

Outer Diameter: 5.6"; Inner Diameter: 4"; LED Quantity: 16 LED (Inner Yellow 6 LED + Outer Red 10 LED); IP65 waterproof light fixture; Drill hole: 3.8" in.(int.)/4.2" in.(ext.);

Easy Installation With High Quality Durable Round Stainless Steel Ring, HARDWIRED with 4-WIRE connection system for Ground, Turn Signal, Brake Light and Running Light: Black Wire - Ground / Red Wire - Brake Light / Yellow Wire - Turn Signal Light / White Wire - Running Light/Tail light

This listing is for a pair of LED cab fender side marker lights with clear lens cover, powered by 12 pieces of super bright amber yellow LED diodes with plug-N-play adapter. Replacement for 2008+ Kenworth T170/T270/T370/T660 Trucks LED Fender Signal Lights Driver and Passenger Side;

Restore excellent night visibility with this high-quality Side Marker Turn Signal Light Assembly. Available for the left and right sides of the vehicle, they are an imperative replacement item for safety compliance. Durable against the elements and against poor road conditions. Replacement of worn or damaged lights restores vehicle's aesthetic appearance. Direct replacement for a proper fit;

Easy to install. 3 Pin weather pack style connector which fits the factory stock wire harness, plug and play. It will stay on once your truck is on;

Package includes 2Pcs Square 39 LED Double Face Led Pedestal Fender Turn Signal Lights with Dual Mounting Studs: 39 Total LED's and 3 Amber Side Marker LED's; Heavy Duty Chrome Plated Housing, Reflector Design; Versatile multi-directional mounting design (up/down/sideway) to turn the light 90 or 180 degrees; universal stud mount design with interchangeable single or double studs;

This Dual-face trailer light is AMBER on both sides! Although in most states in the US it is required for pedestal lights such as this to have an amber face to the front and a red face to the rear, there are some exceptions!;

This amber square dual-face trailer light serves functions: Parking and rear turn signal light; Also you can use it as marker lights; Built-in reflex reflector removes the need for separate reflector and Perfect lights to mount on your truck or trailer side fenders;

Compatibility: These Full Led Fender Side Marker Lights Replacements only suitable for Wrangler TJ 1997 1998 1999 2000 2001 2002 2003 2004 2005 2006 Wrangler tj side markers. NOTE: These are aftermarket products. Pls check the compatiblity first before you buy;

Package includes 1 left (driver) side and 1 right (passenger) side Smoked Amber Wrangler Signal Marker Lights Lamps Assembly, other accessories not included. Part number: 55155628AC, 55155628AB, 55155629AC, 55155629AB, CH2550120, CH2551120;

Upgrade Design: different form those tj side blinker covers on market, these tj marker lamps assemblied with led lights. Each side marker built in 18pcs 3528 Amber LED Chips. Smoke lens makes them almost blend perfectly into the fenders, gives your vehicle a great stealthy look. Amber LEDs illuminate in a nice circular pattern, makes the Wrangler marker lights a unique look at night; And these side indicators built in reflex reflector lens, which removes the need for a separate reflector;

This listing is for a pair of LED cab fender side marker lights with smoke lens cover, powered by 12 pieces of super bright amber yellow LED diodes with plug-N-play adapter. Replacement for 2008+ Kenworth T170/T270/T370/T660 Trucks 12 LED Fender Signal Lights Driver and Passenger Side;

Restore excellent night visibility with this high-quality Side Marker Turn Signal Light Assembly. Available for the left and right sides of the vehicle, they are an imperative replacement item for safety compliance. Durable against the elements and against poor road conditions. Replacement of worn or damaged lights restores vehicle's aesthetic appearance. Direct replacement for a proper fit;

Easy to install. 3 Pin weather pack style connector which fits the factory stock wire harness, plug and play. It will stay on once your truck is on;

Package includes 2pcs round double face sealed LED pedestal lights, which designed for trucks, towing & boat trailers, RVs, buses, ATVs, utility vehicles and also the heavy trucks.

4-1/8" Diameter round. Waterproof, dual-face light serves 5 functions: stop, front and rear turn, tail, and parking light. Front-facing amber lens and rear-facing red lens. Chrome housing. Single post mount.

dual-face design; 21 red LEDs; 21 amber LEDs; Miro-Reflex faceted reflector design provides increased light output and a contemporary appearance while maintaining a traditional footprint;

7-9/16" x 3-5/16" Oval Waterproof LED trailer light with 25 Arrow Amber Leds in Smoke Lens serves as a parking light,a side marker light and a turn signal light(ONE FUNCTION AT A TIME). Durable polycarbonate lens and housing. Surface mount with built-in flange. 3-wire pigtail;

3 WIRES HARDWIRED with 2 steps Brightness: White Wire - Negative, Black Wire - Tail/Running Light/Parking light and Red Wire - Turn Signal Light, Can Modify for Signal Light, Flash Light, Emergency Light ( Flasher relay or Controller not included ); NOTE: It is not Sequential Flowing, just be solid when light on;

Bright lights with durable feature,great for replacing your old LED trailer lights or side; These Lights are impact resistant and less susceptible to shock damage. Each LED Light is water-tight sealed. These LEDs draw less current, generate less heat and are brighter and light faster than an incandescent bulb;

Package Includes 4Pcs Amber 6-3528-SMD LED MARKER / CLEARANCE LIGHT, Supplied with decorative snap-on chrome plated bezel

4-1/3" ( L) x 1-4/5" (W) x 7/8" (H) (approx.) and The surface mount design features the industry standard 3.8" centres.; Used as side marker light, Clearance Light, Cab marker light, Identification Light, turn signal lights, Parking lights, running lights etc.

The PC lens, housing and LED circuitry are all sealed together by expoxy in a single unit to ensure a permanent, weather durable and waterproof seal.

This set features 2pcs 4-1/8" Diameter round Pedestal Mount, Dual Face Trailer Parking and Turn Light. You're going to have amber on one side and then red the other. The amber and red round trailer light is going to serve 2 functions. You're going to have the amber for parking and your turn signal and red side is going to function for stop, turn, and tail light.

Dual face design includes rear-facing red lens and forward-facing amber lens; The wiring design is going to feature 3 wires, black is the ground and the other two wires for either side

About Pedestal mount trailer lights: It is installed standing up from the mounting point. And mounting hardware, typically one or two bolts, is used to secure the light to the trailer.

High Compatibility-Direct replacement for all T10 wedge type W5W W3W 147 152 158 159 161 168 184 192 193 194 259 280 285 447 464 501 555 558 585 655 656 657 1250 1251 1252 2450 2652 2921 2825 PC 175 2886X.

Brighter- each T10 LED light bulbs with 10 x 3528 SMD chipsets LED, much brighter than regular LEDs with high power chips, ideal replacement for dull and yellowish stock bulbs

Long Lifespan- Built in quality high power beams, provide 20000 working hours long lifespan for the led bulbs.

Each marker light built-in 24pcs high power SMD LEDs, Output super bright amber light, Outfitting your truck with this LEDs lights will allow other drivers to see you better at night

LED marker lights design with 3 wire, red wire is high brightness and function as brake/turn signal light, black wire is low brightness and function as parking/sider marker light, white wire for ground

Made of aluminum housing and high quality poly-carbonate lens, rustproof and durable, resistant to shock and vibration. IP67 Waterproof, don't worry about rainy and snow day

Bright Light: The Turn Signal Light built-in 29 LED, Outfitting your vehicle with this light will allow other drivers to see you better at night while lighting the road better than before

Fitment: LED Turn Signal Lights are replacement for Kenworth T600 T660 K300 T300 T330. Driver Side direct Replacement for 39336, K256509, K256-509, P541038, P54-1038 and Passenger Side direct Replacement for 39337, K256509R, K256-509R, P541038R, P54-1038R

IP67 Waterproof: This Parking Lights are made of PC lens and housing with sealed design. IP67 waterproof rating, can withsand to all kind of weather, no moisture inside after rain or car washsing

The amber/white watermelon light built-in 17 LED and design w/reflector cup, clear Lens, Outputting more brighter light; Outfitting your big trucks with LED will allow other drivers to see you better at night while lighting the road better than before

IP65 waterproof rating, fully sealed LED and sturdy PC clear lens, making the watermelon led light not afraid of rain, Keeping your vehicle well-worked and safety ensured

The dual revolution led light is universal fit for trailer, truck, heavy truck, semi truck, Replacement for Freightliner Cascadia Century Classic Columbia Coronado FLD Kenworth Peterbilt International Paystar Prostar TranStar Workstar VNL VNM WIA White GMC and Mack CH Granite, etc

Partsam 2 Amber & 2 Red Square Trailer Clearance and Side Marker Light with Reflex Reflector - Red; Perfect replacement for trailer side marker; 2-4/5" L x 2" W x 1-1/8" D; Reflectorized lens; corrosion resistant; mount on stud; 2-wire; 3 LEDs

Features 2-wire, hard-wired design; The two-wire design includes the lead and ground wires to mount to any surface.; Easy to install, has mounting bolt centered on the back.

Side lens Light and Side marker lights are ALL LED as well ,NOT any incandescent Bulb! Super bright LED quality ,Complies with DOT standards