Best Zhi Yun Professional Video Stabilizers in 2026

【ORIGINAL DESIGN】SMALLRIG Cage Kit for Blackmagic Design Pocket Cinema Camera 4K & 6K includes an integrated full cage, a top handle, and an SSD holder. The basic handheld kit for Blackmagic Camera from SmallRig provides an ideal production tool for the BMPCC 4K & 6K

【MOUNTING POINTS】SMALLRIG 2419 features multiple mounting points including NATO Rail, 1/4"-20 & 3/8"-16 Holes, Locating Holes for ARRI, and Cold Shoe Mount. The cage rig for BMPCC 4K & 6K is locked by 1/4”- 20 screws on both the top and bottom, with additional locating pins and rubber pads on the base plate preventing wiggles or scratches

【FOR HANDHELD SHOOTING】This Top Handle from SmallRig features a shoe mount for microphone and LED lights, is designed for handheld shooting, can hold the weight of a large cage rig with various attachments with ease. The cage kit features a built-in Nato rail that allows you to quickly release accessories with NATO clamp. The handle attaches directly to the cage’s NATO rail on the top and is adjustable fore and aft

Improved Design: 1. A cold shoe is added to the upper right corner of the cage to facilitate the installation of accessories such as Microphone 3468 and LED Video light 3286; 2. Two 1/4"-20 threaded holes with a spacing of 18mm are added at the bottom, which is compatible with SmallRig Quick Release Plate for Arca 3154. A QD hole is added at the bottom, which is compatible with QD quick release shoulder straps and other accessories.

For Sony A7R V/A7 IV/A7S III/A1/A7R IV: SmallRig Cage 3667 is designed for Sony A7R V, A7 IV, A7S III, A1, A7R IV to facilitate low-angle shots and protect the camera while offering a wide range of accessory mounts. NOTE: The HDMI Cable Clamp 3000 is not compatible with Alpha 1 and Alpha 7R IV because it will block the synchro terminal interface when used on the Alpha 7R V.

Multiple Mounting Points: The cage has multiple 1/4"-20 holes and 3/8"-16 positioning holes for ARRI, which can attach accessories such as the upper handle 3765, the side handle 2093, and the monitor stand 2903B. There are 2 built-in cold shoe interfaces, which can install microphones, fill lights and other equipment; the QD hole at the bottom is compatible with QD shoulder straps. Holes are reserved on both sides and bottom of the cage to attach Wrist Strap PAC2456 and Shoulder Strap PSC2428.

【Length】Length of 4 inches / 10cm

【Diameter】The diameter of the rods is industrial 15mm standard

【Inner Thread】M12 inner thread on each end of a rod, so that you can use M12 rod end cap (SmallRig 1617) to prevent your accessories sliding from rods

【For A6300/A6000】The SmallRig Cage 1661 is a formfitting aluminum exoskeleton that protects your camera and offers mounting options to attach accessories. With the camera in the cage, you still have access to the SD card slot, battery compartment, and all camera controls.

【Cold shoe adapter】The A6300 / A6000 cage features a built-in cold shoe for attaching a microphone, articulating arm, or other light accessories

【Various Mounting Points】The built-in shoe mount is used to connect light accessories, such as a microphone, EVF mount and more. A 1/4’’-20 threaded hole at the front enables it to attach to 15mm Micro Rod with 1/4'' Thread 915 for follow focus.

【HIGH CUSTOMIZATION】SMALLRIG Adjustable Monitor Mount 2889 can hold your monitor or accessory onto the handheld stabilizers. The mount is compatible with DJI RONIN-S/RONIN-SC & ZHIYUN CRANE 2S/CRANE 3/3S/WEEBILL-S & MOZA AirCross 2 Gimbals. The monitor mount features three 1/4"-20 threads for additional accessories such as SmallRig Cold Shoe 1241 for microphone or sound receiver.

【ROSETTE MOUNTING PLATE FOR RONIN-S/SC】The mount attaches to the mounting threads for ZHIYUN CRANE 3, CRANE 3S, WEEBILL-S, or WEEBILL LAB with a built-in thumbscrew, and a rosette adapter plate is included to attach the mount to the DJI Ronin-S or Ronin-SC with two included M4 screws.

【ALSO FITS MOZA AIRCROSS 2】For Moza AirCross2, please do attach the Mounting Plate 2826 first before attaching the monitor mount

SMALLRIG Standard Rosette Bolt-On Mount (M6 Thread) 1939 is a multi-functional Rosette (M6, 31.8mm diameter) mount

There are three 1/4-20" and four M2 threaded holes on this rosette mount

It can be attached to a cage, rosette handle and other accessories

New Version: SMALLRIG Cage CCP2646 is the updated version of SMALLRIG Cage 2049. It is specifically designed for Panasonic Lumix GH5 II/GH5/GH5S. This version modified the wooble problem of the old version

Anti-twist: The cage secures to the camera via a 1/4”-20 screw, and features a m2.5 thread on each side to prevent twisting

Buttons Accessible: This cage embraces camera body perfectly and will not block any access to the SD card slot, battery compartment, and all camera controls. This version modified the frame on the top left side to allow you plug in a TC In/Out BNC conversion cable

Compatibility : SMALLRIG Top Handle with Locating Holes for ARRI 3765 is designed to facilitate low-angle shot and reduce burdens on arms, compatibility for Universal cold/hot shoe mount

Lightweight Only 124g : Hollowed-out design makes it weigh only 124g. Mostly made of aluminum alloy, together with anti-slip and anti-freeze silicone

Built-in Cold Shoe Mounts : It has 3 front cold shoes and 2 rear cold shoes that allow simultaneously mounting microphone, LED light, monitor, and other accessories

【VERSATILE CAGE】SMALLRIG VersaFrame Cage 1584 is a full-covered cage for medium-sized cameras: Canon 80D, 70D, 60D, 50D, 40D, 30D, 6D, 7D, 7D MarkII, 5D MarkII, 5D MarkIII, 5DS, 5DS R, Nikon D7000, D7100, D7200, D300S, D610, DF, Sony A99, and of course almost any medium-sized DSLR on the market

【ADJUSTABLE HEIGHT】The height of the cheese rods is 145mm, the width of this cage is 196mm. With the 15mm cheese rods on each side, you can adjust rod height to accommodate different cameras. And please note that the maximum inner height of this camera cage is 118mm

【FULL-ASSESSIBILITY】Secured the cage tightly via the hot shoe connector on the top and 1/4'' screw on bottom, and it would not block any buttons and card slot on the camera

【FOR DJI Ronin S GIMBAL】SmallRig Rod Clamp Ring 2221 is exclusively designed for DJI Ronin S stabilizer. Secure tightly via 2 long M4 screws on sides, compact and durable

【MOUNTING OPTIONS】This Mounting Ring features 1/4’’-20 threaded holes on each side and 2 arri 3/8’’ locating holes on two sides, allows you to attach more accessories, such as Articulating Arm 2070, which can greatly prevent your monitor from accidentally falling off

【BUILT-IN NATO RAIL】Built-in NATO rail on botch side can be mounted with accessories with NATO clamp, such as SMALLRIG Articulating Arm 2028

【New Version】This SMALLRIG top handle is a new version, the cheese-style grip is ergonomically designed to offer a more comfortable handheld experience

【Please Note】The handle could NOT be used on camera cage directly. The shoe mount adapter of the top handle fits any camera with a standard hot shoe, such as camera for CANON R5/R6/R7, for Sony A7 IV etc.

【Load Capacity】It could be directly mount onto the hot shoe of small mirrorless camera for low angle shooting. The maximum load of this camera handle is 1.5kg

FOR DJI Ronin-S/SC and RS 2/RSC 2/RS 3/RS 3 Pro/RS 3 mini: Designed for DJI Ronin-S/SC and RS 2/RSC 2/RS 3/RS 3 Pro/RS 3 mini Handheld Gimbal. It provides multiple mounting holes for accessories attachment such as monitor mount 2070

INSTALLATIONS: It is fixed on the side of Gimbal for Ronin S &SC via two M4 screws after taking off the small plate for DJI which covers the electronic contacts

NATO RAIL: Comes with Nato rail for the Nato Side Handle 1688/2187

【Whole Solution for Vlogging】SmallRig Professional Phone Video Rig Kit 3384B is specially designed for vlogging and live streaming, and supports both handheld shooting and tripod shooting. The kit includes a universal phone cage 2791, two side handles 2772, a desktop tripod BUT2664, a mini LED light 3286, a microphone 3288, a power bank holder 2790, a cold shoe mount 1241, 2 cables,etc.

【Wide Application】The phone cage is compatible with phones with a width range from 62mm to 86mm. Suitable for most smartphones, such as for iPhone 14/14 Pro/14 Pro Max/ for iPhone 13/13 Pro/13 Pro Max/12/12 Pro/12 Pro Max,for Huawei for Samsung, etc.

【LED Light】Video LED Light is a lightweight, portable and stylish mini-LED light, with 0-100% brightness control, CRI95, and color temperature scale from 2700K to 6500K. The light comes with a built-in 2200mAh lithium-ion battery, which is charged via the included USB Type-C charging cable and features a 105-minute operating time (maximum brightness).

SmallRig Extension Arm with Rosette 1870 is an adjustable rosette arm with NATO rail device. It could be used on both sides.

It is equipped with standard rosettes (M6, 31.8 mm diameter) on opposite ends. It provides 167mm-255mm of extension for ARRI standard rosette handgrips and other gear

With a NATO rail in the middle, which allows to adjust the distance forwards and backwards just through quickly tightening and loosening the M5 thumbscrew

WHAT IS THIS: HDMI Cable Clamp is designed to firmly hold your cable in place while plugging into your cage, which can prevent your cable from falling off

DESIGNED FOR CONVENIENCE: Secure with a 1/4’’ screws, compatible with SmallRig Cage 1661 ( for Sony A6000/A6300/Nex7), SmallRig Cage 1889 (for Sony A6500), SmallRig Cage 2049 (for Panasonic GH5), SmallRig 1815 (for Sony A7/ A7S/ A7R), and SmallRig 1950 (for Panasonic Lumix DMC-G85/G80)

FEATURES: Anti-slip surface on the clamping opening to protect HDMI cable from dropping off, which can be also adjusted in size to adapt different Micro HDMI Clamp

▶ NATO Clamp Ballhead: Attach cage with NATO rail with on the other end via ballhead with NATO clamp, while it could attach monitor cage on the other end via ballhead with 1/4’’ screw

▶ Quick Release & Adjust Angle: It features quick release and attachment and could be slid to get the balance of the whole kit.The monitor mounted on it could be adjusted in different positions and angles via both the ballhead and ballhead clamp

▶ Precision locking device: A single wingnut is applied to lock the double ballhead tight directly, and thumb screws on both ends are utilized to lock the devices manually and a spared hex spanner is ready to lock it tighter

【LIGHTWEIGHT CHEST PAD】SmallRig MD3183 is designed for reducing the sense of the weight of long-term handheld shooting, in order to make the shooting process more labor-saving and stable. If you operate your camera in the center front of your body when in handheld mode, you could add this Lightweight Chest Pad 3183 to your 15mm LWS rig for a comfortable stabilizing option.

【MOUNTS ONTO SEPARATE 15MM LWS RODS】The pad mount features a 15mm LWS rod clamp that can mount onto any standard, separately available 15mm rods, and it can slide back and forth for adjustment along the rods. You can connect the camera through SmallRig 15mm rods such as 851 and SmallRig universal baseplate 1674, support it on the abdomen or chest for shooting.

【ROTATE UP TO 150°】The rotating structure can be adjusted by 150°, and the damping feeling can be adjusted by the included Allen wrench.

【Design for iPhone 14 Pro Max】This Dual handheld video stabilizer kit is designed for iPhone 14 Pro Max, it features two handles for stable shooting and vlogging, with one wireless control side handle for efficient shooting. The phone video rig comes with multiple 1/4''-20 threaded holes and two cold shoes for attaching SmallRig tripod BUT2664, video light 3808, microphone 3453, as well as hand strap, etc.

【With External Lens Mount】The lens backplane adaptor of this video rig kit can be compatible with M-mount lens or replace the SmallRig 17mm backplate adapter 4079 (not include) to connect 17mm threaded lens. (Does not affect the use of smartphone buttons, radar, ultra-wide-angle lens and wireless charging functions)

【Quick Release and Locking Structure】One-click disassembly and assembly, and convenient operation. Support horizontal and vertical shooting can help video bloggers / Youtuber / filmmakers realize live streaming, fast filming and get the ideal photo angle.

【Carbon Fiber 15mm Rods】 Made of 9 layers of carbon fiber, these 15mm rods are resistant to corrosion, impacts, bending, and high heat, ideal for both indoor and outdoor video production. Matte finishes also eliminate reflections that might spoil your image

【Lightweight Yet Sturdy】 Compared to conventional aluminum alloy rods, the weight of this 15mm rod set is significantly reduced to 2.5oz (70g). Yet the rigidity remains to support various accessories with great security

【Universal Compatibility】 This 15mm rod set is compatible with shoulder rigs, camera cages, baseplates, and rod clamps that feature the standard rail support system. 12inch (30cm) in length, it also allows flexible and smooth positioning

【CAMERA SHOULDER RIG】The camera shoulder rig is an assembly of SMALLRIG Rubber Handle 1963, Extension Arm 1684 and Rosette Bracket 1898

【STABILIZE SHOOTING】The shoulder rig support comes with two handles with rubbers, improve your hand-held shooting and eliminate jitters while you are taking a still video and RUN&GUN shooting

【COMPACT DESIGN】Updated Rosettes for tighter installation. Made of aluminum alloy, durable and sturdy build, fix firmly and securely

Compatibility: SmallRig camera all-in-one full cage is customized designed for Nikon Z 6II and Z 7II with MB-N11 battery grip to protect camera and prevent from scratching, provided mounting points to attaching accessories

Anti-deflection Design: Z 6II/ Z 7II camera rig is securied via one 1/4''-20 screw at the bottom and one M2.5 screw on both sides, featured silicone cushions to prevent scratches and maintains access to buttons, card slots, battery door, and flip screen

Multiple Mounting Points: Bulit in 1/4"-20 threaded holes and 3/8"16 threaded holes for top handle 3765, 1638, side handle 2093, 2425, monitor mount 2903B, 2904B, magic arm 2115C, two cold shoes for microphone 3468, LED lights 3405

COMPATIBILITY: SmallRig L-Shape Grip for Nikon Z fc Camera 3480 is designed to provide a comfort grip. The retro-style handle shares similar texture and color with the camera; the baseplate shares the same silver surface treatment with the camera and fits perfectly

VERTICAL SHOOTING: The L grip secures to the camera via a 1/4"-20 D-ring screw on the bottom and comes with a built-in 1/4"-20 threaded hole on the grip that enables vertical shooting on a tripod

TRIPOD SHOOTING: The baseplate features a built-in plate for Arca Swiss to quickly switch to tripod shooting, and a 1/4"-20 threaded hole at the center that supports tripod or quick release plate for Manfrotto

Compatibility: SmallRig camera all-in-one full cage is customized designed for FUJIFILM X-H2 / X-H2S with FT-XH Battery Grip/VG-XH Battery Grip to protect camera and prevent from scratching, provided mounting points to attaching accessories

Anti-deflection & Anti-scratch: X-H2 / X-H2S Camera cage locks the camera via one 1/4''-20 screw at the bottom and two side lock adapters, and features several rubber cushions to prevent scratches

Multiple Mounting Points: It comes with 1/4 "-20 and 3/8"-16 threaded holes for top handle 2165 & 1638, side handle 2093 & 2425, for HDMI cable clamp 1693 for stable data transmission, monitor mount 2903B & 2904B for attaching monitor, magic arm 2115; two cold shoe mounts for microphones, LED lights, etc

Enlarged Hot Shoe Space: The new version of the cage enlarges the space around the camera hot shoe, and now you can use the cage together with the Microphone ECM-W2BT for Sony, Flash HVL-F32M or other accessories that require the use of the hot shoe on the top of the camera.

Enlarged Battery Compartment Space: The space for the battery compartment at the bottom of the cage is enlarged, making it easier for you to change memory cards. The cage does not interfere with the use of buttons, card slots, battery compartments, and flip screens. There is a slot in the battery compartment to place the dummy battery cable. When using the dummy battery, the camera can also be placed flat on the table.

Multiple Mounting Options: The cage has built-in multiple 1/4"-20 threaded holes, 3/8"-16 positioning holes for ARRI, which can be used with the Top Handle 1638, 1446, 1984 and 2165 for low-angle shooting; it can also be installed with a Power Bank Clip BUB2336 to fix the power bank near the camera for continuous power supply. There is a built-in cold shoe on the top and bottom of the cage, which can expand the Microphone 3468 and LED Video Light 3286 for a complete vlogging solution.

For DJI RS 3 Mini / RS 3 / RS 3 Pro / RS 2 / RSC 2: SmallRig Sling Handgrip 3028C designed for the DJI RS series reduces arm fatigue and adds stability to low-angle gimbal shots. It can support up to 8 kg / 17.6 lbs and adopts a longer arm bracket, making it more versatile for RS 3 Pro and larger camera setups.

Optimized Ergonomic Design: This gimbal sling handle has been updated with a curved design that better fits ergonomics. Its grip length has been increased with finger stops, providing a more comfortable and secure grip for larger hands. Constructed with a combo of silicone and aluminum alloy, it is lightweight but strong. Its sleek design and compact structure match perfectly with the stabilizer.

Quick Release Features: It securely attaches to your gimbal with a NATO clamp, with anti-removal stud for safe and quick operation. On this version we integrate a NATO rail on the side, allows for mounting SmallRig 3026B to provides a good spot for your monitor. Additionally, a QD socket is added, providing the option to mount a QD neck or shoulder strap for additional support.