Best Laser Pullers in 2026

EASY TO USE: Slide flat end of puller through center of bearing and flat against backside of bearing, then slide washer down the center of the shaft against front side of bearing and tighten the nut on smaller end of puller, then thread a slide hammer (not included) to the puller and slide hammer back and forth until the bearing comes out; The washer captures the bearing firmly to distribute the applied force over the entire bearing and prevent damage

Use the VCT Pneumatic SAE Standard Rear Axle Bearing Puller 3-Piece Service Set – Domestic Car Vehicle Bearings Removal Tool Kit to service semi-floating rear axle bearings on your vehicle; These tools make the job simple and prevent damage to your bearings when pulling; Much easier than claw-type axle bearing pullers that slip off and chew up the old bearings; For removal only, not intended for installation

FITS YOUR CAR: Standard SAE sizes work for most American domestic makes and models; Set includes the following sizes to fit main bearing tube – 1 inch to 1-7/8 inches, 1-5/16 inches to 2-3/8 inches, and 1-3/8 inches to 2-7/8 inches; Sizes permanently laser-etched on tool for easy identification; Each tool fits a basic slide hammer with a 5/8-inch x 18 thread pitch

[ High Quality ] --- This is a two jaw gear puller, which is made of carbon steel, the point of the mandrill through a special heat treatment process, more solid and durable. This tool is used for tearing down ball joint in parts of the combined mandrel brake system.

[ Easy Operation ] --- Use the two jaws to catch the bearing; Rotate the mandrel with the thread; Slowly pull out the bearing of the shaft. The puller can be bilateral rotation, enable laser stretching size and working space.

[ Wide Application ] --- Widely use in various bearings that are not easy to disassemble. Perfectly fit for automotive flywheel, motorcycle wheel, car wheel, scooter motorcycle bearing and gear and so on.

[ High Quality ] --- This is a two jaw gear puller, which is made of carbon steel, the point of the mandrill through a special heat treatment process, more solid and durable. This tool is used for tearing down ball joint in parts of the combined mandrel brake system.

[ Easy Operation ] --- Use the two jaws to catch the bearing; Rotate the mandrel with the thread; Slowly pull out the bearing of the shaft. The puller can be bilateral rotation, enable laser stretching size and working space.

[ Wide Application ] --- Widely use in various bearings that are not easy to disassemble. Perfectly fit for automotive flywheel, motorcycle wheel, car wheel, scooter motorcycle bearing and gear and so on.

Applications: Vauxhall/Opel, Vectra B, Zafira B, Omega B, Tigra A, etc

Use in conjunction with 17 mm socket/spanner

2 legged puller and thrust nut

UNIVERSIAL FITMENT---This bearing gear removal is professionally manufactured and only used in a wide range. It is suitable for automobile flywheels, motorcycle wheels, bicycle wheels, pump bearings, generator bearings, machine bearings, etc.

​SIZE ADJUSTABLE--- This bearing gear puller has two jaws with adjustable jaw depth, which is suitable for gears and bearings of different sizes. The puller can rotate in both directions, which can realize the laser stretching size and working space.

EASY TO INSTALL--- This bearing gear remover, with hexagonal screws and threads, is fastened, not perforated, and has high strength. It is very easy to install and use, saving time and energy.

​SIZE ADJUSTABLE--- This bearing gear puller has two jaws with adjustable jaw depth, which is suitable for gears and bearings of different sizes. The puller can rotate in both directions, which can realize the laser stretching size and working space.

UNIVERSIAL FITMENT---This bearing gear removal is professionally manufactured and only used in a wide range. It is suitable for automobile flywheels, motorcycle wheels, bicycle wheels, pump bearings, generator bearings, machine bearings, etc.

PREMIUM MATERIALS--- This two-jaw bearing gear is made of chrome vanadium steel with a mandrel that has undergone a special heat treatment process to make it more durable. High temperature resistant, not easy to corrode and wear.

Carbon Steel Material: The bearing gear puller is made of high-quality carbon steel material, the point of the mandrill through a special heat treatment process, solid and durable for long service life

Bilateral Rotation Design: This bearing puller tool is used for tearing down ball joint in parts of the combined mandrel brake system; The puller can be bilateral rotation, enable laser stretching size and working space

Two Jaw Design: Two jaw with adjustable clamping depth, which makes the bearing puller fit for different size gears and bearings

Carbon Steel Material: The bearing gear puller is made of high-quality carbon steel material, the point of the mandrill through a special heat treatment process, solid and durable for long service life

Two Jaw Design: Two jaw with adjustable clamping depth, which makes the bearing puller fit for different size gears and bearings

Bilateral Rotation Design: This bearing puller tool is used for tearing down ball joint in parts of the combined mandrel brake system; The puller can be bilateral rotation, enable laser stretching size and working space

Durable Carbon Steel Material: This Two Jaw Bearing Gear Puller is made of carbon steel, the point of the mandrill through a special heat treatment process, more solid and durable

Bilateral Rotation: The puller can be bilateral rotation, enable laser stretching size and working space

Adjustable Depth: Two jaw with adjustable clamping depth, fit for different size gears and bearings

Made of carbon steel, the point of the mandrill through a special heat treatment process, more solid and durable

Made of carbon steel, the point of the mandrill through a special heat treatment process, more solid and durable

The puller can be bilateral rotation, enable laser stretching size and working space

Fit for : Fit for gear and bearing removing, a good car repair tool.75mm bolt type two jaw gear puller.

Fit for : Fit for gear and bearing removing, a good car repair tool.75mm bolt type two jaw gear puller.

Premium Quality: Two Jaw Bearing Gear Puller is made from chrome-vanadium steel with forging and special heat treatment.

High Quality: Made of carbon steel, the chuck tip goes through a special heat treatment process, more solid and durable.

Adjustable: Two jaws with adjustable clamping depth, suitable for gears and bearings of different sizes.

Bilateral rotation: The puller can be bilateral rotation, achieve laser stretching size and working space.

Bundle Include: A -- 9 discs collar axle housing with carrying case master/universal aluminum bush drive seal kit for automotive wheel bearings. B -- 5 ton Capacity bearing separator, pinion wheel bearing removal kit with 2" and 3" jaws, wheel hub axle puller set, heavy duty bearing splitter tool kit with case.

A1 -- Forged from high strength aluminum for extra durability and strength, the driver and discs feature extraordinarily long service life and don’t mark bearings. The solid, knurled handle offers extra grip and control during use. Collars/discs of 9 different sizes fit standard races used in most wheel bearing applications.

A2 -- To use, simply select the correct bushing, align straight and centered, and then pound in/out. Suitable for straight installation on cars, small engine trucks, motorcycles, etc. Our 9-disc and 1-driver set simplifies bearing installation for everyone from master mechanics to DIY novices. Our super sturdy and well-designed tool set guarantees long service life without damaging your bearings.