Best Vct in 2026

1/4" Drive: T8, T10, T15, T20, T25, T27, T30

3/8" Drive: T40, T45, T50, T55

1/2" Drive: T60

EASY TO USE: Slide flat end of puller through center of bearing and flat against backside of bearing, then slide washer down the center of the shaft against front side of bearing and tighten the nut on smaller end of puller, then thread a slide hammer (not included) to the puller and slide hammer back and forth until the bearing comes out; The washer captures the bearing firmly to distribute the applied force over the entire bearing and prevent damage

Use the VCT Pneumatic SAE Standard Rear Axle Bearing Puller 3-Piece Service Set – Domestic Car Vehicle Bearings Removal Tool Kit to service semi-floating rear axle bearings on your vehicle; These tools make the job simple and prevent damage to your bearings when pulling; Much easier than claw-type axle bearing pullers that slip off and chew up the old bearings; For removal only, not intended for installation

FITS YOUR CAR: Standard SAE sizes work for most American domestic makes and models; Set includes the following sizes to fit main bearing tube – 1 inch to 1-7/8 inches, 1-5/16 inches to 2-3/8 inches, and 1-3/8 inches to 2-7/8 inches; Sizes permanently laser-etched on tool for easy identification; Each tool fits a basic slide hammer with a 5/8-inch x 18 thread pitch

This continuous use transformer is capable of both up and down voltage conversions for Japan and USA electricity to enable use of Japanese products in USA and USA products in Japan

1000 Watts is the maximum capacity of this transformer including the power surge

It converts 110/120 volt USA power to 100 volt Japan power AND 100 volt to 110/120 volts (means it will convert the American power to Japanese power and also convert Japanese power to American)

This clamp is perfect for woodworkers working on cabinets and wooden boxes! Just slide the pipe clamp through any length 3/4 in. pipe to hold wood in place for gluing and drilling! Constructed of tough cast iron that keeps wood steady as you work, this clamp is a great addition to any woodworking work bench at the home or shop!

This clamp is limited only by the length of the pipe you supply

Four plate clutch for high clamping pressure, quick release

The VCT Jumbo Pry Bar Tool – 36” Inch Large Breaker Crowbar with Oversized Mechanics Handle for Heavy-Duty Automotive Prying is what you need to do serious pry work – Do not settle for anything less; Use in an automotive shop to check steering, suspension, brakes, or loose ball joints, bearings, and bushings on vehicles; Use when you need extra leverage, on the farm, or anywhere that involves work on heavy equipment

ANY SPACE, ANY ANGLE: Sharpened, bevel-end angled nose tip creates an extra leverage point and slips into tight spots so you can work in any space and at any angle

BUILT TO LAST: Heavy duty heat-treated chrome-plated long pry bar with 3/5” x 3/5” inch (16mm x 16mm) square shaft

12pcs Punched Set: This all-in-one hole puncher kit contains everything you need to punch. Great for making clean holes in gaskets, leather, plastic, rubber and other soft materials.

Special Design: The solid metal hole punchers are upgraded with precision ground flutes and cutting edges, making them easy to grip when working on woodworking crafts, metal imprinting or repairing gaskets.

1/8", 5/32", 3/16", 7/32", 1/4", 5/16", 3/8", 7/16", 1/2", 9/16", 5/8", 3/4" You'll have a heavy duty hole punch to meet all of your hole punching needs!

This 9 pieces heavy duty mechanic plier set is ideal for majority mechanic operation. The hardened teeth for all pliers are perfect for cable cutting, fixing, and tightening. Nickel finish full cover surface prevents it from corrosion and rotten. Soft rubber grip handles enable a non-slip grip.

Drop forged, heat treated fully polished

Includes canvas caring pouch for easy storage

* Installs, removes, trims and tightens many types of clip-on wheel weights

* Features a special, mar-free installation of specially coated wheel weights used on alloy wheels

* Coated handles for comfort grip

This set of screwdriver bits is perfect for rounding out any tool kit. Each of these bits features a 1/4” shaft for use with power drills, screwdrivers and screw guns. The set includes hex, Pozi, Phillips, slotted, Torx and tamper-proof Torx bits plus a magnetic hex bit bolder packed in a convenient storage case for easy portability.

Durable S2 steel for long life, use in higher torque applications Hex, Pozi, Phillips, slotted, Torx and tamper-proof Torx bits Magnetic hex bit bolder Storage case included

Includes: 6 Hex Bits: 2mm, 2.5mm, 3mm, 4mm, 5mm, 6mm 5 Pozi Bits: (2) PZ1, (2) PZ2, PZ3 5 Phillips Bits: (2) PH1, (2) PH2, PH3 4 Slotted Bits: 3mm, 4mm, 5mm, 6mm 7 Torx Bits: T10, T15, T20, T25, T27, T30, 740, 8 Tamper Proof Torx Bits: T8, T10, T15, T20, T25, T27, T30, T40

Universal Bearing Packer

4.2" cone diameter

Evenly injects fresh grease while forcing out old grease

Fast on/off conserves media and reduces mess

Spring loaded paddle trigger

Nonslip vinyl grip, Carbon steel body

*Fully Polished *Comfort Grip Handles *Heavy Lined Teeth

11" long,Straight,45%,90% And "S" Shape

includes canvas storage pouch

* For use the most all oxygen sensors no matter what size electrical connectors they have

* Double-sided design, 12-point configuration on one side and 6-point on the opposite side

* 12-point side enables twice the number of "clock angle" attachment positions allowing oxygen sensor removal in difficult areas

This Double Box End Ratcheting Set includes 5 pieces composed of chrome vanadium steel with a mirror polished finish. The universal spline drive fitted on each piece is compatible with 12-point, 6-point, rounded 6-point, Spline, E-Torx and Square fasteners. Great for working in tight spaces.

Chrome Vanadium Steel with a Mirror Polished Finish Universal Spline Drive works on 12-Point, 6-Point, Rounded 6-Point, Spline, E-Torx and Square fasteners Extra-Long Design, Unique extra long design provides more torque than other similar wrenches in the market

Classic 12 point, 72 teeth ratchet gear needs a minimum of 5 degree swing arc that is perfect for restricted, hard to reach work spaces 180 degree rotating flexible heads allow you to apply leverage at any desired angle and get around obstructions Great for Tight Spaces Non Reversible Design

Manufactured from high grade satin polished steel

This spring compressor tool has a wide range of OHV, OHC and CVH engines but not suitable for use on engines with deep seated valves. Compressor for springs works on dual springs, inner, and outer springs making it a multi purpose tool. Over all length: 250mm/9.8 inches

Professional overhead valve spring compressor, very easy to use. Easily remove and install valve springs without removing cylinder head from motor. Valve removal jaws are offset to properly grip parallel compression springs

These safety wire pliers are really three tools in one: wire cutter, wire twister and a pair of pliers.

You can grip, twist and snip faster and easier.

To operate, just grasp wire, pull handle and it puts any number of twists needed.

7-piece 3/8" Drive Extra Long SAE Set: 110" mm X 1/8; 3/16; 7/32; 1/4; 9/32; 5/16; 3/8"

Constructed of High Grade Chrome Vanadium Alloy Steel

Mirror Chrome Finish Drop Forged & Steel Heat Treated S2 Bits

SAE 1/4" DRIVE DEEP SOCKET SET W/ HOLDER Includes: 8 sockets: 3/16", 7/32", 1/4", 9/32", 5/16", 11/32", 3/8", 7/16" and 1 holder

METRIC 1/4" DRIVE DEEP SOCKET SET W/ HOLDER Includes: 8 sockets: 5.5MM, 6MM, 7MM, 8MM, 9MM, 10MM, 11MM, 12MM and 1 holder

Chrome Finish Drop forged Carbon Steel

Shaft Diameter: 7/8"

Bearing material: Chromium Steel (Grc15)

Housing material: cast iron

Suitable for metal straight panel or curved panel complex industry. These small fixtures hold panels of any shape anywhere-edge-to-edge, and are fully fixed before butt welding, leaving only a small gap that allows the weld to fully penetrate. Once the two parts are tack welded together, the wing nut is loosened, and the elbow lever is removed and the clamp is removed from work before final welding.

To align and clamp sheet metal panels for precise spot welding,butt welding,edge-to-edge welding and tacking in place

For precise spot welding, positioning, butt welding and edge-to-edge welding, fully align and clamp the metal plates.

REMOVE CONNECTION CLIPS: Use the Snap Ring Plier Set to remove snap ring (circlip) retaining rings on your lawn mower, tractor, shredder, farm equipment, truck, car, SUV, or other vehicle while performing brake pad removal and routine maintenance

Reversible joints and adjustable jaw precision screw bit allow for 2 types of function on both internal and external retaining rings

Use included hook and pick tools to clean out gunk, get into hard-to-reach areas, and properly grip dropped clips

The hydraulic ram that hooks right up to a 10 ton hydraulic pump, like in a 10 ton portable power. This is perfect for body work on trucks, tractors, and heavy equipment.

This unit is made for bending, straightening, and pulling. Use for auto/truck body work, farm, construction equipment, old home and barn restorations and a lot more.

10 Ton Maximum ram capacity, Rugged forged steel swivel hooks, 5" pulling distance.

The 5-1/2 in. blade on this hot knife quickly heats to 975° F to make fast, clean cuts in foam and plastic materials. The hot knife comes with a depth adjusting sled to make repeat cuts or long cuts at a precise depth.

Cuts foam, EIFS, ICF, nylon rope, webbing, synthetic fabric, and plastic

Easy push-button activation, auto-off for safety

This transfer punch set takes the guesswork out of transferring threaded, drilled or reamed machining, for accurate hole-drilling operations in home or hobby work.

Each punch is made high quality heat-treated alloy steel with a black oxide finish for durability and rust resistance to ensure long lasting service life of your tool set in your tool collection.

The precisely machined point on the transfer punches is suitable for toolmakers and machinists alike and allows the user to execute accurate holes of the same size when needed.

MINIMIZE DAMAGE: Use the Dead Blow Sledge Hammer Rubber Mallet to minimizes damage of hammered surface

FINISH THE JOB: Automobiles, construction, and other delicate or metal surfaces you want to prevent from marring and sparking; Works as a bumping hammer for heavy gauge truck fenders and panels and also works to straighten reinforcements and braces

NO MORE BOUNCE BACK: Soft double faced mallet surface is safe as it is a non-marring hammer that prevents sparks, absorbs energy, and prevents dangerous bounce-back; Double face mallet has 6.9-inch x 4-inch head with 4-inch x 4-inch rounded faces

10 Pack 1/2" BOW SHACKLE CLEVIS SCREW PINS ANCHOR

SCREW PIN: .63" DIAMETER

WORKING LOAD: 2" TON

A very handy way to add some extra storage space to your work area.

Trays can be attached to your toolbox, inside your van, to the side of the vehicle while you work etc. Magnets and contact points are covered with rubber to prevent scratches.

6" Tray with 2 magnets, 1.5lb capacity 8" Tray with 4 magnets, 1.8lb capacity 10" Tray with 4 magnets, 2.2lb capacity 12" Tray with 4 magnets, 2.6lb capacity

Easily loosens frozen/rusted screws, nuts or bolts

Tightens fasteners without stripping

4 bits for slotted and Phillips fasteners

Check angles from 0 to 90 degrees

Accurate to 0.5 degrees

Magnetically attaches to metal squares for easier reading

Drop forged, heat treated chrome vanadium steel for increased durability against high fatigue and wear as well as corrosion resistance and increased toughness

Notches in sockets lock onto ratchets/extensions for easy change and handling

Deep Design provides improved access to hard to reach areas