Best Huepar Rotary Laser Levels in 2026

⭐【Fully Layout with 3 x 360° Line Lasers】: One 360° horizontal and two 360° vertical planes enable users to cover the floor, wall, ceiling all around the room. The three laser lines can be selected individually depends on job site applications. With our smart pendulum system, this laser level tool self-levels and indicates out-of-level condition while pendulum unlocked. Once pendulum locked, it switches to manual mode to lock lines for use at any angle.

⭐【Dual Power Methods & Type-C Charging Port】: Huepar B03CG Laser Level employed a large capacity of 3.7V / 5200mAh lithium battery and provides up to 8 hours of running time. The lithium battery comes with a Type-C charging port that can be charged separately. When taking out the battery, the laser tool can be used at the job site by plugged in. 4 battery indicators on the keypad allow users to know the current battery volume and charging protection helps prevent from overcharging.

⭐【Brighter Green Laser & Outdoor Pulse Mode】: This cross line laser adopts the bright Osram’s green laser unit, which is resistant to temperature changes and has higher stability. At the same power, the green laser is twice bright as the red laser, with a working range up to 85 feet (300LUX) of accuracy within ±1/9 Inch at 33 Feet. The outdoor pulse mode can be activated by pressing the Pulse Mode Button, allowing to extend the laser range up to 200 feet with Huepar Line Laser Detector.

✔️HUEPAR DEDICATED RECEIVER- Huepar LR-6RG receiver can ONLY be used with Huepar Line Laser Levels that feature Pulse Mode Function. Please pay attention to that this receiver can NOT be used with Rotary Laser Level. And the receiver can NOT be used with Huepr 9011G&9211G laser level. It is recommended to use in accompany with Huepar 902CG/901CG/8211G/BOX-1G/BOX-1R/GF360G/HM03CG/S03CG/S04CG/S03DG/LS04CG/LS03CG/LS41G/GF360R/622CG/622CR/621CG/621CR/603CG/603CR/602CG/602CR/DT03 Laser Level, etc.

✔️AVAILABLE FOR RED AND GREEN PULSE LASER- It is necessary to Turn ON the Pulse Mode of the laser level when using with Huepar LR-6RG laser receiver. This receiver allows detection of Red and Green pulse laser beams in difficult light conditions, distances up to 200ft (60m).

✔️CLEAR MULTI-SIDED READOUTS- Ergonomic design with display on the front, side and back of receiver, offers easier visual readout. This unit is outfitted with a dual-sided Bubble Vial on both the front and top, in order to more accurately determine the level.

🌞4x360° LINE LASERS&PULSE MODE(RECEIVER INCLUDED): This laser tool provides four 360 planes of laser light. The top 360° horizontal line can be used for ceiling installation. The 360° floor horizontal line is for tiling installation. Two 360° vertical lines cross at 90°angles makes user quickly visualize and finish square layout. Pulse mode extends laser range up to 200Ft. with Huepar Laser Receiver included in the kit. The laser uses bright Osram’s green laser unit that has higher stability.

🌞LCD DISPLAY&BLUETOOTH TECH: The laser level has LCD screen to easily get the status of the battery, angle, pendulum and pulse mode on the display. Bluetooth connectivity enables to control the setup of the laser from across the room with Huepar App on smart phone and remote control. The App and remote control can switch ON/OFF the laser lines and pulse mode, select the laser planes. Huepar App also provides out-of-level alarm. The laser tool can connect two Bluetooth devices simultaneously.

🌞TRIPLE POWER METHODS & TYPE-C CHARGING PORT: This 360 laser tool adopted 7.4V / 2600mAh Li-ion battery (can be purchased easily at local market) for extended run-time, or with 4 AA alkaline batteries. Besides, this 4D laser level can be used at job site by plugged in when take out the battery. With Type-C charging port, the 16 lines laser level can also be charged by laptop, power bank, car charger, etc.

【High-Performance Laser】Exterior working range can be up to 700M in diameter with a detector, accuracy of +/- 1/8" at 100Ft. The red beam has strong stability, low power consumption, and high-cost performance. The red beam is more suitable for indoor use. The scanning speed can be adjusted at 0→300→600rpm, and the angle of scanning will continuously change as follows:0°→10°-→45°-→90°→180°-→0°.

【Automatic Alignment】 Electronic Horizontal self-leveling makes this rotary laser self-level up to 5° within 15s. If the RL300HR gets disturbed on the job it relevels itself automatically. The self-leveling motors are accurate to ±10 arc seconds. Slight movements can be ignored in windy or other vibrating conditions while turning on vibrate mode. In vibrate mode, the self-leveling function is deactivated and the cross is locked to use the device at any angle.

【Dual Slope Function】Electronic dual-slope function allows the user to perform a slope of 5 degrees in both X and Y axis. The slope of the Y-axis and the Slope of both X&Y-axis can be set by the remote control. This dual-slope mode works perfectly when checking grade, setting drainage, landscaping-terracing, or other slope work. This is a great laser tool for any job from DIY to large commercial construction, and everything in between.

EFFICIENT MULTI-LINE LASER TOOL: Huepar NT411G multi-line laser level projects one horizontal line, four vertical lines plus plumb down point -for leveling, aligning plumb and square applications. Users can short press H and V to switch the laser lines, Vertical lines cross at 90° angles in the ceiling, forming the up point to divide surfaces at a right angle. 4 vertical lines covering the ceiling, walls, and floor, effectively separate the room.

LI-ION BATTERY & TYPE C CHARGING PORT：Huepar Level laser tool adopted 3.7V / 2500mAh Li-ion battery for extended run-time about 4hours. 4 battery indicators on the Li-ion battery allow users to know the current battery level and charging status. There is a Type-C charging port on the Li-ion battery pack that can be charged separately. And the laser tool can also be charged by laptop, power bank, car charger, etc.

ROTATING BASE & 5/8" THREAD APPLICATION: The laser level with a metal micro-adjust fine turning pivoting base offers 360° rotation, the micro rotary knob enables users to make 360°adjustment and height adjustment, combined with the built-in bubble which enables adjustment of the position of the laser tool on uneven or sloping ground. The laser level comes with 5/8"-11 thread, laser dot can be projected through the 5/8" thread and suit for standard tripod or laser mounting pole.

⚠【HUEPAR DEDICATED RECEIVER】- Huepar LR-5RG receiver can ONLY be used with Huepar Line Laser Levels that have Pulse Mode Function‼ Please note the the receiver can NOT be used with Rotary Laser Level‼ And the receiver can NOT be used with Huepr 9011G&9211G laser level‼ It is recommended to use the detector in accompany with Huepar 901CG/902CG, BOX-1G/R, 8211G, 621CG/R, 622CG/R, 602CG/R, 603CG/R, GF360G/R, etc. Can also be used with Tacklife SC-L03 / SC-L04 Laser Level.

⚠【AVAILABLE FOR RED AND GREEN PULSE LASER】- It is NECESSARY to Turn ON the Pulse Mode of the Laser Level when using with Huepar LR-5RG laser receiver‼ The receiver allows detection of Red and Green pulse laser beams in difficult light conditions, distances up to 200 feet.

⭐【Large Reception Window & Dual LCD Display】- Large reception window of 2 inches and optical and acoustic signals help to locate the laser plane quickly and accurately. Dual LCD displays for easy visual readout on both sides of the receiver. LCD backlight provides a clear look even in low light conditions. Adjust the height until the horizontal datum line and the arrow disappear on the LCD display.

✔️MOUNTING CLAMP: Huepar LP36M-S Mounting Clamp is designed especially for Laser Mounting Pole LP36.With a 3.5cm / 1.28inch diameter slot for easy mounting on poles. The clamp is equipped with an easy-to-use pressure lever, securely locking the pole in place to ensure stability and accuracy. Install several laser levels at different heights on the support bar, suitable for multiple people working at the same time, such as installing ceilings, windows and wall skirts at the same time.

✔️MULTIPLE INSTALLATION METHODS: Removable back clip and the strong magnets, the bracket can be attached to metal surfaces. Slots for screws, nails, raceways or optional straps are designed to make the installation much firmer. 5/8"-11 female thread makes it possible to be attached to a tripod or laser pole. Fix the bracket to the ceiling by two screws on the top of the bracket. Huepar LP36-M Positioning Bracket is ideal for any job site.

✔️360°ADJUSTABLE BRACKET: The bracket can be placed at any height of the rod according to your needs. With a Height Fine-tuning knob, help to adjust the height within 7cm / 2.76inch, and the horizontal rotation 360°. An added locking knob enables to fix the working height and avoid sliding up and down.

⚠ HUEPAR DEDICATED RECEIVER- Huepar upgraded version LR-8RG receiver can ONLY be used with Huepar Line Laser Levels that feature Pulse Mode Function. Please pay attention to that this receiver can NOT be used with Rotary Laser Level. And the receiver can NOT be used with Huepr 9011G&9211G laser level. It is recommended to use in accompany with Huepar 902CG/901CG/8211G/BOX-1G/R/GF360G/R/HM03CG/S03CG/S04CG/S03DG/LS04CG/LS03CG/LS41G/621C/R/603CG/R/ B series and P series Laser Level, etc.

AVAILABLE FOR RED AND GREEN PULSE LASER- It is necessary to Turn ON the Pulse Mode of the laser level when using with Huepar LR-8RG laser receiver. This receiver allows the detection of Red and Green pulse laser beams in difficult light conditions, distances up to 200ft (60m). Accuracy: high accuracy ±1.5mm, it easily directs the user to position the laser higher or lower on a grade rod. This ensures an accurate level of reading all the time.

90dB SOUND & DOBLE VISUAL SIGNALS: Beep sounds will remind you when you find the target. Devices that are to be used indoors can reduce the sound level as it may get too loud and irritate those around you. As for open spaces, the device needs to be loud for people to hear it over a distance. As for visual signals, the LED indicators are strong enough to be visible in broad daylight. Most of the work that you do would be in the daytime, and the strong sunlight may often cause a problem.