Best Partsam Running Board Light Assemblies in 2026

Warning: Wires come out from the conner, NOT from the center. (Check image 2)

Partsam (7) Amber + (7) Red Oval Oblong Side Marker Light Lamps; It is Universal For all auto esp. RV Trailer Camper Boats etc. 【Tip: wires were brought out at the lower corner of the light and not the center,】

Can be function as Side Marker Lights, Clearance Lamps and Indentification Lamps, Trailer Lights etc.

Package incldues 2 Pieces White 7" Round LED Backup lights with reflex lens. Screws and thick mounting gaskets are included for complete mounting.

This is a 7 Inch Round LED Reverse lights which has 36 LEDs and works great for transit vehicles, bus, utility, and dome light applications. This 7" White LED Bus Tail Light is sonically sealed and waterproof with a surface mount light with mounting gasket. With the built-in reflex, the reflector in the center of the light can be visible from a long way off. They mostly works with the 7" round LED stop tail turn lights;

This 7 inch round back-up Light is 12V DC and is hard wired with separate ground wire: white is ground, black wire is dimmer for taillight/running light, and red wire is brighter for back up/revese lights mode. NOTE: These 7" School Bus lights can be used but they do not have flashing patterns. But with a proper relay it can be a flasher;

Brand: TMH with 1 Year Premium Warranty

Pack of 50 pcs : 3/4 inch Amber Light + Amber Lens Round Bullet Miniature side marker

Brightness : 60 lumen each light with 3 pcs High Quality SMD LED 100,000hrs Lifetime

[VISIBILITY AT 120%] The sleek tailgate light bar adds style and safety that gives your rig an enhanced look. No need to worry about being unseen on the dark road. Exceptionally bright up to 30ft away!

[COMMAND ATTENTION] Integrated sequential turn signals. Redline Triple offers 5 functions: running, turns, brake, reverse, and hazards. 200-300% Brighter than 1st gen and most competitors on the market.

[BACKBONE OF A BEAST] IP67 waterproof body, give your truck that premium look and gets you seen out there on the road. Mount 2 ways: Mounting clips or heavy duty 25lbs rated 3M adhesive tape or use BOTH!

Part # 264155BK, Exact Fits for 2002 - 2007 Sierra Silverado 1500 1500HD 2500 2500HD 3500 trucks with factory installed cab marker lights. 2007 Silverado 1500 1500HD 2500 2500HD 3500 Classic trucks.

Built with 30LED Beam, provide super brightness and enhance visibility when driving at night.

With IP65 Waterproof design, No worry about driving in foggy day, heavy rain and snow.

Impressive brightness: The 70inch running board lights includes 216pcs high intensity LED chips, amazing super bright lighting output,it is powered by 72 LEDs of white for door/step/DRL/parking lights and 144 LEDs of amber color for sequential turn signal lights.

Light Function: Amber Turn Signals/Running Lights - Sequential flashing amber lets other drivers know what's about to happen. White Courtesy Lights - When the doors are opened or the LED dome light is activated, bright white LED chips will illuminate the ground to help you and others get in and out of your car.

IP67 Waterproof & Strong adhesive: IP67 waterproof, transparent plastic tube protect the LED strips to work well. In addition, strong adhesive and cable ties ensure stable installation. Even driving through lots of rain, highway speeds, potholes, the LED strips can still stay on and work great. Please clean down the dust, oil, and water before installing, the adsorption force will be stronger.

【High-quality & Long-lifespan】T10 Led bulbs build with high quality LED interior bulbs each designed with 15 high power SMD 4014 chips. Much brighter than halogen bulbs. High-quality electronic components, thickened glass fiber board, stable performance, long lifespan up to 50000+ hours. 360-degree lighting angle

【Specifications】Voltage: 12V, Color: 6000K white, Power: 1.5W, Lumen:400lm, Length 0.98in/24.8mm *Width 0.39in/9.9mm. Standard T10 socket. CANBUS error free for 98% vehicles. Easy to install, Non-Polarity, just plug and play.

【Fitment】 This T10 led bulb fits well 147, 152, 158, 159, 161, 168, 175, 184, 192, 193, 194 2825 W5W etc. For a better purchase experience, please double check your manual before making purchase.

Self adhesive back led strip ,easy to install

waterproof easy to clean

Low power consumption,long service life

What is it? - This is 2Pc customizable logo car welcome light, we can customize any logo, such as photo, text, graphics (Please note: Custom LOGO time need 5 days, shipping time is 10~12 days, you can receive it in 17 days).

Features: magnet induction switch design: automatic light on when you open the door, the light automatically goes off when you close the door, so your car becomes cool and unique from then on, can also be used as a car warning light to prevent accidents.

Easy to install: no wiring, no drilling, no harm to your car, 3M sticker is super strong and durable, will not fall off, 1 minute to install.

[THE EXCLUSIVE SEQUENTIAL TURN SIGNALS] The only sequential light to shine light on the road. Sync the Sidekick Running Board to your turn signals, courtesy lights, parking lights or running lights to ensure everyone knows your command.

[SUPER BRIGHT YOU'D BE AMAZED] With our exclusive OPT7 design, the Sidekick Running Strip allows brightness at an output more than 100% even in daytime. Get ready to turn heads & stay LIT even in stormy weather!

[DOOR ASSIST] - Impress them at the door! White courtesy Light will be activated whenever the doors are opened, which allows your passengers to enter and exit in a style with light!

[Upgrade details 1] The new puddle lights Compatible with Tesla Model 3/Y/S/X comes with an extension cable, no external cable is required. no-damage installation, Convenient and fast, reducing installation risks.

[Upgrade details 2] The aluminum part on the back of the old door light is too large, which is difficult to pry out after being installed. The aluminum part of new puddle light is smaller and easy to disassemble and replace.

[Upgrade details 3] The new puddle light is made of Carwiner lamp chips, high-definition glass and five lenses, which has high definition, larger pattern, and the pattern is not out of shape. The old door light is made of ordinary lamp chips and three acrylic lenses, which pattern will be deformed, bluish, and low brightness.

🚓【2023 Newest Design】Customized for Tesla Model Y Model 3 Model X Model S. Integrally injection-molded, will not separate and deform during installation. Perfect gifts to husband, motor club friends, wife, father, son, friends, car fans.

🚓【Upgraded Aluminum Alloy Shell】Designed with Aluminum back cover, Better heat dissipation, Long life-span. Our tesal door lights made of high temperature resistant transparent flame retardant material, more safer and stable.

🚓【High Brightness, Never Fade】Tesla projector light features high-lens film, has a clear projection and powerful light transmission, which effectively reduces the lens color cast and ensures a bright and clear picture.

Compatible models:(Note: This door light is not suitable for Infiniti QX60) Compatible with Infiniti Series:Infiniti FX (FX37/FX50) 2007--2020; Infiniti G (G25/G37) 2007--2020; Infiniti Q50 2013--2020(2016 Except); Infiniti (Q60/Q70) 2013--2020; Infiniti M (M25/M35/M37) 2007--2020; Infiniti EX (EX25/EX35/EX37) 2008--2020; Infiniti (QX50/QX70/QX80)2013-2020; Infiniti QX56 2011-2020

Easy to install: plug and play! No drilling, no wiring, no disassembly, and no damage to your car. Note: When you want these marker lights as replacement lights, please make sure that your car has original door lights first.

Super performance: high-definition highlight projection. Using high-brightness LED chips, very bright lighting output, very low power consumption.When the door is opened, the LOGO lights up on the surface of the opened door to provide lights to assist in and out of the vehicle.

🔵BETTER CHIP DECODING TECHNOLOGY: Used newest car decoding circuit chip, will not conflict with car software. Use high-quality circuit boards and parts, which can carry more current, absolutely eliminate the noise caused by high current.

🔵INSTALLATION EFFECT: When you open the car door, you will see the bright and vivid logo light projects on the ground. It will be turn off when you close the door.

🔵HD PROJECTION FILM & HD LENS: Using a high-brightness Led bulb with 500 lumens, the light passes through a high-definition heat-resistant film, and after passing through an ultra-high-definition lens, an undistorted and decolorized pattern will be displayed on the ground.

3.4" x 1.1" Oblong; waterproof LED trailer light serves as either a side marker light or a clearance light when properly mounted; suitable for trailers, off road vehicles, golf carts, car haulers, truck running board and more

Ultra slim, die-casting aluminum housing with durable polycarbonate colored lens over colored LEDs, resistant to shock and vibration

DOT compliant safety light; built-in 4 PCS SMD LEDs, features premium optics to output bright red or amber light, making them ideal for front or rear, side or top of vehicle applications, improve visibility at night, in fog or raining day

Fitness: These back lights are compatible with Toyota 86 2012 2013 2014 2015 2016 2017 2018 2019 2020. Subaru BRZ 13 14 15 16 17 18 19 20, Scion FRS 2013 2014 2015 2016. Please keep all user manuals, barcode on box or on the lights. If you have issues with our lights, please just contact us.

Plug and Play: Back lamp or taillights are easy to install. Designed to be an exact replacement for your factory lights. No splicing required. Professional installation is recommended. If you have issues with installation, please confirm with us.

Benefits: LED reverse lights, fog light, super bright. Refresh the look of your car and change your car style, and gives you and your family safer night-time driving. Including turn signal with sequential indicator, LED daytime running light.

【Quality Improvement】Our products are the latest high light transmission and high temperature resistant glass lenses, which are not faded, not deformed, and long lasting. (Not a product that fades and the logo becomes blurred after 1-3 months of used.)

【Clearer Compatible Instructions】Our nissan door lights logo fit for most Nissan Altima ARMADA MAXIMA TITAN Pathfinder QUEST TERRA . Detailed compatible car models please refer to the description page. Please make sure your car has original door light at first. (Please note: Some models have rear doors without door lights)

【Easy to install】Control circuit board separate from LED - Improve heat dissipation efficiency, prolong service life, LED base will not fall off. Makes it easier for you to install, no wiring, no damage the car, easy to disassemble, 3 minutes to install.

[Dress you car Cool] ★ HD projection, very bright lighting output, Brighter than typical ghost shadow light on the market, and very low power consumption, The film projection can be replaced optionally. This product is wirrliss especially designed for auto modification fancier and it will not destroy the original car appearance bring more driving fun to drivers. Automotive lighting decoration, pleasing light visual experience, improve the grade of the car.

[Easy installation] ★ No need drill hole, no wiring, no disassemblying, Just stick the light lamp on the door panel and stick the magnet on the bottom of the car frame. No harm to car. It can be installed in both left & right door. Courtesy door light make your car artistic moreover the atmosphere.

[Perfect Performance] ★ Courtesy door light make your car artistic moreover the atmosphere. Lighting steady and constant, clear and soft. The feature is very shine, the welcome light will be displayed on the ground after the door is opened, the owner are given more respect by the brand car. Perfect gifts to husband,motor club friends, wife, father, son,friends, car fans.

Package includes partsam 4pcs 6 inch Led utility strip bar Lights 21LED, Clear Lens and White when lit; Stainless Steel Screws and Black rubber gaskets are included for mounting to all surfaces. Also the rubber gaskets have a little grove in the back of them so they will lay flat, thus, these trailer lights can be mounted on a solid surface and the wires run along instead of through the surface;

They measure 6" from side to side and 2/3 wide. Also this white led strip is about 3/4" tall without the gasket, the gasket adds another 1/8" making them 7/8" tall. Hole distance 5"; This 12V DC RV Boat Led strip Light is hardwired with two bare end wires, not a diming light(on/off switch not included): Black is ground and Red is positive(hot);

This boat light mounts to a flat surface needing only the 2 screws to penetrate the mounting surface; They can be used virtually anywhere you need light. We truly have customers using them as running board led lights, grill daytime running lights, boat courtesy lighting, boat interior lights, golf cart lighting, boat cockpit lighting, boat cockpit indirect lighting, transom accent lighting, console lighting, RV Camper Lighting etc.

5 pieces each order (each lamp size 5.50" x 3.25" x 1.50")

Built with 12 pieces White LED lights inside

DOT SAE approved and replace Part # 11516638, 15599040, 15691885, 8C34-15442-CB, 8C34-15442-AD

Good Performance : Adopting Cree LED chip which has high brightness output but low consumption;using high transmittance and multi-layers lens,make sure clear and vivid emblem projecting;and equiped with well-performed mainboard,good heat dissipation.HD car door light projector provides a bright,clear and vivid emblem shadow on the ground

Function : When the door is open, the clear,bright and vivid LOGO emblem will be projected into the ground.It allows you to show your great hospitality to your business partners,friends and families and provide them with elegant touch, it also can be used for puddle light

Easy to Install : Using flathead screwer to pop out your current lights, unplug them, plug our emblem lamp in, and pop them back into the placement.No harm to car.Just need 2 mins to finish installing.

【2PCS-70"Board Running LED Light】: Our Board Running LED Light have 174 super bright LEDs with 2835-SMD (87 Amber LEDs and 87 White LEDs), we use additional ground wire inline fuses to make it more safer.

【Waterproof rate】: IP68 rated, waterproof, dustproof, anti-corruption for harsh environment, durable and flexible with up to 30,000 hrs lifetime.

【Fitment】: Recommended for Extended Cab & Crew Cab Trucks. Install simpler, drive safer, look particular, wonderful upgrade experience.

➤➤ Easy to Install,Stick and Play ➤➤It takes only about five minutes to stick the logo projector on the the lower edge of the inner door panel and stick the magnet on the sill. THEN IT’S DONE. NO drilling, NO wiring, NO disassembling, NO damage to your vehicle at all.

➤➤ Functional and Decorative Lights ➤➤When the door is opened, a crisp and bright logo is illuminated to the ground,super cool and notice puddles. And it provides lights to aid safe entry into and out of the vehicle, meanwhile alert the passing vehicles of the opened door.Brilliant move to protect your families, friends better.

➤➤ Magnetic Sensing to Work Automatically ➤➤The lights projector will Turn ON automatically when you open the door(lamp departs the magnet), and turn OFF automatically when close the door(lamp overlaps with the magnet). How convenient.

🏍[MOTORCYCLE TAIL LIGHTS ] Made of Soft Rubber, plastic and 2835 SMD and 3014 SMD LED. it could be used in rainy day.

🏍[MOTORCYCLE BRAKE LIGHTS ] Size : 20.5 x 1.3cm / 8 x 0.5in . Soft board, can be bent and deformed.

🏍[LED BRAKE LIGHT STRIP ] Universal flexible 48 LED motorcycle light strip / tail brake stop light / turn signal light / license plate light.

🚙 [Special note] Our vehicle model application table is shown in the second figure, which clearly lists the corresponding models. Please know whether it fits your model before ordering. If you have any questions, please contact us

🚙【Easy installation car door LED light logo Car door projector lights】Plug and play! No drilling,no disassembling,no damage to your car.Used newest car decoding circuit chipNo connecting wires required will not conflict with car software.Girls can also easily install.

🚙【LED car logo lights function】Door light logo,When the door is openthe clearbright and vivid LOGO emblem will be projected into the ground.t allows you to show your great hospitality to your business partnersfriends and families.HD car door light logo projects on the groundstanding out your car.Cae logo light door also can beused for puddle light

Partsam (2 x Red in clear lens) 6.3" 24 LED Brake Stop Tail Turn Lights with rubber grommets and 3-Prong Wire Pigtails;.

LED Quantity: 24PCS; Voltage: 12V; Color: Clear/Red; Light Size: 6.3" x 2.14" x 1"; Size with grommet: 7.28" x 3.2" x1.1"; you need an about 6.4" hole to install it; PC lens and housing welded together to ensure a permanent and water proof seal; LED circuit board coated with conformal coating for excellent moisture and environmental protection;

HARDWIRED WITH THREE WIRES: Black Wire - Ground; Red Wire - high brightness for stop/turn /brake lights; White Wire - low brightness for tail or running lights; Please Kindly Note: We have 2 different types of this light: one with White wire for ground, and the other with Black Wire for ground. Both with red wire for high brightness and are of the same quality, and will not affect your usage;

High brightness LED, logo looks great within 5 meters (200inch) at night.

Easy to replace the logo, don't need to remove the light.

Infrared Sensor Light, automatically turn on/off when the door open/close.

COOL EFFECT: Please refer to the video of QA to see the effect after installation, The car door logo light projects your 3D car brand logo on the ground when the car door is open, it will be turn off when you close the door, avoid wasting electrical energy.

HIGH DEFINITION & BRIGHT PROJECTION: This Courtesy Welcome Lights is Powered by 12V power cord, using high brightness LED chips. When you open the car door, the light passes through a high-definition heat-resistant film, and after passing through an ultra-high-definition lens, an undistorted and decolorized pattern will be displayed on the ground.

BETTER CHIP DECODING TECHNOLOGY: LED Ghost Shadow Projector adopt newest car decoding circuit chip, will not conflict with car software. Use high-quality aluminum plate circuit boards and parts, which can carry more current, absolutely eliminate the noise caused by high current.

Partsam includes 2 Pieces 15 Inch White LED Trailer reverse light Bar and 2 Pieces 15 Inch Red Led trailer stop turn tail light bar, 4 Pieces in total. Other mounting hardware not included;

Each 15 inch Led trailer tail light bar is powered by 11 high power LED for a bright performance. These Led Strip Bars are HARDWIRED with a three wire pigtail: white is ground wire, Black is the low brightness and Red is the high brightness. Functions of trailer led light bar: red led light bar functions as stop turn brake light in high mode and tail or running light in low mode; white light bar function as backup light bar or reverse light bar in high mode and side marker light in low mode;

Dimension of the trailer light strip: The overall length is about 15.5 inches, wideth is about 1.25 inch, and the thickness is about 0.5 inch. There is a little knob where the wires all come out, so the overall depth is about 1 inch, and you may need to cut out a hole to allow that to go in. The spot knob is about 0.57 inch in diameter. Really a nice slim low profile unit;

【Chasing Dream Color Running Board Lights】 Smartphone APP Control, Chasing Dream Color, Effect rgb running board lights, as long as you install the APP, you can set your own lighting scenarios in advance by adjust the change speed, brightness and stroboscopic speed.

【Running Board Lights for Trucks】90Led, 150CM=59INCH, DC 12V. Waterproof, Flexible chasing dream color, you can switch your favorite colors. Let your travel fascinating with 59Inch RGB Running Board Lights.

【Easy to install Truck Led Running Board Lights】Included double side tape at the back side.Easy to use,low power consumption. Note: Clean the place you are going to put the running board lights firstly.