Best Aursinc in 2026

[Upgraded Version: ESD Protection Diodes] Produced by Hugen, tinysa with latest hardware V0.3.1, the displayed version info is "ESD protected" meaning the diodes are installed which will be more stable and sensitive with higher antistatic level and longer service life. NOTE: Due to the old inventory might mix with the new batch, and If you got the old version TinySA and want a new one, you could apply a replacement for it.

[Frequency Range] Spectrum analyzers like the tinysa use a resolution filter that is used to isolate the input power in a small frequency range. This resolution filter is swept across the desired frequency range. The fastest scanning speed occurs with an RBW or 300kHz or wider and is about 2 scans per second. But with increase of the frequency span and decrease of the RBW the scanning speed decreases quickly. A scan from 0MHz to 350MHz with an RBW of 10kHz takes about 2 minutes.

[2 in 1 Device] When not used as Spectrum Analyzer it can be used as Signal Generator, MF/HF/VHF sinus output between 0.1MHZ-350MHz, UHF square wave output between 240MHz-960MHz. Built-in calibration signal generator that is used for automatic self test and low input calibration. The tinysa contains all the components of a conventional heterodyne swept spectrum analyzer. Color display showing 290 scan points covering up to the full low or high frequency range

【Efficient Electric Pump】Oil change pump, a great helper for quick and clean oil changing and transfer, all parameter is verified by multiple test. Diesel Flow Rate: 1.5L/min, Engine Oil Flow Rate(40-60℃): 0.3L/min, Inlet Tube Length: 1.2m/47.2in, Outlet Tube Length: 1.4m/55.1in, Voltage: 12V, maximum current: 5A, maximum power: 60W

【NOTES】A, This oil transfer pump CAN NOT transfer WATER, GASOLINE, PETROL, FUEL or FLAMMABLE LIQUID. B, Please DO NOT misplace the direction of import and export, positive and negative poles and secure the hose clamps. C, Heat up your engine oil to 104°F-140°F before pumping D, We tested oil pump before shipping, there might be little oil stain in the pump, kindly understand. E, To make it last longer, it’s recommended to keep a little oil inside when the extractor pump is not in use.

【Premium Quality】The quality of oil change pump extractor varies widely. We are using pure copper for the motor and alligator. Good electrical conductivity, corrosion resistance and rust free, effectively avoid leakage or short circuit. Overheat protection will cut off the power supply automatically for safety

【Efficient Electric Pump】Oil change pump, a great helper for quick and clean oil changing and transfer, all parameter is verified by multiple test. Diesel Flow Rate: 1.5L/min, Engine Oil Flow Rate(40-60℃): 0.3L/min, Inlet Tube Length: 1.2m/47.2in, Outlet Tube Length: 1.4m/55.1in, Voltage: 12V, maximum current: 7A, maximum power: 80W

【NOTES】A, This oil transfer pump CAN NOT transfer WATER, GASOLINE, PETROL, FUEL or FLAMMABLE LIQUID. B, Please DO NOT misplace the direction of import and export, positive and negative poles and secure the hose clamps. C, Heat up your engine oil to 104°F-140°F before pumping. D, We tested oil pump before shipping, there might be little oil stain in the pump, kindly understand. E, To make it last longer, it’s recommended to keep a little oil inside when the extractor pump is not in use

【Premium Quality】The quality of oil change pump extractor varies widely. We are using pure copper for the motor and alligator. Good electrical conductivity, corrosion resistance and rust free, effectively avoid leakage or short circuit

Latest Feature: TF is not required for this hotspot, the main board is the latest design by our team -- jumbospot. Power up boot time: under 30s; Runs without an SD card; USB/WEB update Firmware; USB Console Function; Simple Setting Page; Simple Log View Function; System Firmware Size: Max 32M; Running Current: Under 300ma @5V; Factory Reset WPS button.

Widely Compatible: Supports DMR (Brandmeister), D-Star , System Fusion (FCS, YSFReflector), P25 , NXDN ,Pocsage networks.

Easy to Use: Very easy to use, works without a computer. No additional hardware required, works out of the box. All accessories included. Web interface for configuration and monitoring. Runs fully embedded software, running on an openwrt operating system. No TF card, bulky Windows software or failing SD cards.

The manual can be downloaded from the Product guides and documents section on the product page

【On Every Wavelength】 AURSINC am fm radio is a DSP digital demodulation radio based on SDR software-defined radio architecture. It has a 192kHz width spectrogram and waterfall display capabilities, and cooperates with 16bit sampling to realize a high dynamic receiver with CW, AM, SSB, FM demodulation functions

【Frequency Range】 100KHz-149MHz; Step Frequency: 1Hz/10Hz/100Hz/1kHz/10kHz/100kHz/1MHz/10MHz; Antenna Interface: BNC male, impedance 50Ω, maximum input power -20dBm. Control Method: Resistive touch screen or Rotary encoder. Channel Saving: 99 channels and channel name can be preset

Si4732 AM FM Radio: Based on the Si4732 chip, the short wave radio can receive FM, AM(MW &SW), LW, CW, SSB(LSB & USB). FM:64-108MHz, AM:520-1710kHz, SW:1711-29999khz, LW:153-513kHz. With the antenna, the transistor radio bring the best reception and multiple bands, let you have more choice of radio channel(Talk show, music, News station or sport,etc). Giving you a relax time with your family and friends

2.8in Touch Screen & 2500mAh Battery: The small radio adopt 2.8 inch LCD color touch screen with high sensitivity and adjustable brightness, so you can read details on the screen clearly whether indoors or outdoors. Built-in 2500mAh rechargeable battery, it can be used for a long time(about 10 hours) without worrying about sudden power failure

Loud and Clear: The shortwave radio receiver has AGC and ATT function. AGC circuit can stabilize the signal and improve the receiving effect and ATT function is helpful to control noise and distortion caused by signal strength overload. Therefore, this radio can receive signals well and the sound is clear without noise

[2022 UPGRADED HW V3.6] NEW HW VERSION: V3.6 with MicroSD card port now can have the measurement data or the screenshots saved in the it at anytime. Added battery circuit management, more secure. Redesigned PCB, you can connect to mobile phone with Type C-Type C cable( original PCB needs OTG cable), see a clear HD image on your phone. Added a case, which is protective and dust-proof. Disply: 2.8 inch TFT (320 x240)

[IMPROVED FREQUENCY ALGORITHM: The improved frequency algorithm can use the odd harmonic extension of si5351 to support the measurement frequency up to 1.5GHz. The 50K-300MHz frequency range of the si5351 direct output provides better than 70dB dynamic, The extended 300M-900MHz band provides better than 60dB of dynamics, and the 900M-1.5GHz band is better than 40dB of dynamics

[MULTIPLE FUNCTIONS] The default firmware main function is used for antenna performance measurement. The TX/RX method can measure the complete S11 and S21 parameters. If you need to obtain S12 and S22, you need to manually replace the transceiver port wiring. Designed a practical and simple control application on PC, you can download touchstone(SNP) files for radio design and simulation software

[2021 Upgraded Version: ESD Protection Diodes] Tinysa with latest firmware V3.0, the displayed version info is "ESD protected" meaning the diodes are installed which will be more stable and sensitive with higher antistatic level and longer service life. Spectrum Analyzer with two inputs, high quality MF/HF/VHF input for 0.1MHZ-350MHz, lesser quality UHF input for 240MHz-960MHz. Switchable resolution bandpass filters for both ranges between 2.6kHz and 640kHz.

[Frequency Range] Spectrum analyzers like the tinySA use a resolution filter that is used to isolate the input power in a small frequency range. This resolution filter is swept across the desired frequency range. The fastest scanning speed occurs with an RBW or 300kHz or wider and is about 2 scans per second. But with increase of the frequency span and decrease of the RBW the scanning speed decreases quickly. A scan from 0MHz to 350MHz with an RBW of 10kHz takes about 2 minutes.

[2 in 1 Device] When not used as Spectrum Analyzer it can be used as Signal Generator, MF/HF/VHF sinus output between 0.1MHZ-350MHz, UHF square wave output between 240MHz-960MHz. Built-in calibration signal generator that is used for automatic self test and low input calibration. The tinySA contains all the components of a conventional heterodyne swept spectrum analyzer. Color display showing 290 scan points covering up to the full low or high frequency range

✔️Upgraded Version: Not only testing standing wave impedance of the antenna, can also debug the duplexer, the insertion loss of the filter, the isolation and testing the attenuation of the cable, shorten the coefficient, the phase, the amplification of the antenna amplifier

✔️ 3GHz vector network analyzer, designed in collaboration with OwOComm. Under the LGPL license agreement, it is completely manufactured according to the v2_2 files issued by OwOComm at Development Department, in line with the original technical specifications，please refer to below path to get the firmware updated: drive. google .com/drive/folders/1Lr7AOTg2pAhYBZDfaiPVZTMZkFO14PMj

✔️The SAA-2N/NanoVNA_V2.2 uses a similar user interface to the NanoVNA, but with a different technical architecture, the SAA-2N/NanoVNA_V2.2 does not load the initial calibration data at startup, and does not automatically interpolate the calibration data after the user changes the frequency, and must recalibrate or call back the calibration data after each startup and frequency change. Please read the user manual carefully before use to avoid damaging the device

This is a DIY product that provides perfect vector network measurement capabilities(no enclosure)

The metal shield (no enclosure)for tiny vector network analyzer is designed to reduce the external interference and improve the measurement accuracy

Designed a practical and simple control application on PC, you can download touchstone(SNP) files for radio design and simulation software. Added a case, which is protective and dust-proof. Disply: 2.8 inch TFT (320 x240)

Multiple high sensitivity sensors installed for detecting Power line, Smart meter, Cell phone, Microwave etc.

Identify/recognize the common possible sources, such as Power line, Cell Tower, Microwave, Static etc.

Safety suggestion lets you understand current situation instantly.

[Upgraded Version: ESD Protection Diodes] Produced by Hugen, tinysa with latest hardware V0.3.1, the displayed version info is "ESD protected" meaning the diodes are installed which will be more stable and sensitive with higher antistatic level and longer service life. NOTE: Due to the old inventory might mix with the new batch, and If you got the old version TinySA and want a new one, you could apply a replacement for it.

[Frequency Range] Spectrum analyzers like the tinysa use a resolution filter that is used to isolate the input power in a small frequency range. This resolution filter is swept across the desired frequency range. The fastest scanning speed occurs with an RBW or 300kHz or wider and is about 2 scans per second. But with increase of the frequency span and decrease of the RBW the scanning speed decreases quickly. A scan from 0MHz to 350MHz with an RBW of 10kHz takes about 2 minutes.

[2 in 1 Device] When not used as Spectrum Analyzer it can be used as Signal Generator, MF/HF/VHF sinus output between 0.1MHZ-350MHz, UHF square wave output between 240MHz-960MHz. Built-in calibration signal generator that is used for automatic self test and low input calibration. The tinysa contains all the components of a conventional heterodyne swept spectrum analyzer. Color display showing 290 scan points covering up to the full low or high frequency range

😊【2022 UPGRADED NANOVNA ANALYZER】: SeeSii Nanovna-h4 Vector Network Analyzer is developed by Hugen. With latest 4.3 version,10KHz-1.5GHz measure range,4.0 inch LCD touchscreen,mini and portable design.This Antenna Analyzer is provides outstanding vector network measurement capabilities and perfect for evaluating antenna resonance and SWR.It is a very handy & smart analyzer for electronics engineer, amateur radio operators or radio diy amateurs.

😊【BUILT-IN MICRO-SD PORT & TIME DISPLAY】: The lastest antenna analyzer with MicroSD card port,so you can save field test data or screens to a MicroSD card at any time,support up to 32GB memory card. (Not include in the pacakge).In addition, different from old version NanoVNAs, the date and time can be customized, which is convenient for you to further record and save data..The default firmware main function is used for antenna performance measurement.

😊【IMPROVED FREQUENCY ALGORITHM】:The Vector Network Analyzer can use the old harmonic extension of si5351 to support the measurement frequency up to 1.5GHz. The 50K-300MHz frequency range of the si5351 direct output provides better than 70dB dynamic, The extended 300M-900MHz band provides better than 60dB of dynamics, and the 900M-1.5GHz band is better than 40dB of dynamics.Great for trouble shooting antennas and improving performance.

【Frequency Range 】Tiny Spectrum Analyzer with two inputs, high quality MF/HF/VHF input for 0.1MHZ-350MHz, lesser quality UHF input for 240MHz-960MHz. Switchable resolution bandpass filters for both ranges between 2.6kHz and 640kHz. Color display showing 290 scan points covering up to the full low or high frequency rangefrequency range. The tinySA contains all the components of a conventional heterodyne swept spectrum analyzer.

【Built-in Calibration Signal Generator】When not used as Spectrum Analyzer it can be used as Signal Generator, MF/HF/VHF sinus output between 0.1MHZ-350MHz, UHF square wave output between 240MHz-960MHz. Built-in calibration signal generator that is used for automatic self test and low input calibration.

【Tiny Spectrum analyzers & ESD Function】Switchable resolution bandpass filters for both ranges between 2.6kHz and 640kHz.Color display showing 290 scan points covering up to the full low or high frequency range. Bulit-in rechargeable battery allowing a minimum of at least 2 hours portable use.The performance of the 2021 latest version 3.1 will be more stable and sensitive, with a new ESD protrcted function enable the product to have a higher antistatic level and a longer service life.

<p>◙【<b>Built-in 2-in-1 Calibration Signal Generator</b>】This TinySA Spectrum Analyzer built-in calibration signal generator that is used for automatic self test and low input calibration.When not doing spectrum analyzer,it can be used as signal generator with two frequency outputs,MF/HF/VHF sinus output for 0.1MHZ-350MHz and UHF square wave output for 240MHz-960MHz.</p>

<p>◙【<b> Frequency Range</b>】The tinySA Spectrum Analyzer displays 290 scanning points,covering the entire range of low-frequency or high-frequency ranging frequencies.0.1 MHz -350 MHz high quality IF/HF/VHF input,240 MHz -960 MHz low quality UHF input.A switchable resolution band-pass filter suitable for the range from 2.6 kHz to 640 kHz.</p>

<p>◙【<b>PC Control</b>】TinySA Spectrum Analyzer can be connected to PC through USB and realizes the serial over USB (CDC) protocol,which can call a large number of commands.The Windows driver will be automatically installed after connecting to the Windows computer.The Linux driver is built into the kernel.</p>

Frequency Range from 9 kHz up to 1.5 GHz

10 Hz Minimum Resolution Bandwidth

Min. -161 dBm Displayed Average Noise Level (Typ.)

All-Digital IF Technology

Frequency Range from 9 kHz up to 2.1 GHz

-161 dBm/Hz Displayed Average Noise Level (Typ.)

Frequency band: 15MHz-2.7GHz; Frequency span: 112KHz - 100MHz

Backlight for great indoor visibility; Graphics LCD 128x64 pixels, great visibility outdoors

PC Windows client supports Windows XP/Vista/Win7 both 32 and 64bits

[Impressive frequency range] – Scan and diagnose any frequency starting in low frequency 50KHz up to high frequency 6.1GHz, with no gaps or limitations. Offering this wide operating range, it can detect all WiFi, cell stations and phones, IoT, HAM bands, Digital radio and TV, ISM bands, Drone links and pretty much all wireless technologies used in todays demanding communications world.

[Robust design and instant power up] – A fully armored metallic enclosure provides robust mechanical strength and the high quality baked varnished paint provides a unique glossy finish. The device is designed and manufactured to last many years of demanding usage in the field, with internal rechargeable Lithium battery for hours of continuous usage.

[Advanced features] – Included advanced high-resolution Spectrum Analyzer mode, WiFi Analyzer mode, Tracking SNA. Internal firmware is continuously updated with additional features and functions to improve the device capabilities.

【New TinySA Ultra Mode】The ULTRA Tinysa developed by Hugen can reach an ultra-wide frequency range from 100kHz to 5.3GHz. The 4-inch large screen provides clear data images and sensitive operation touch. It also has a new ESD protection function, installed the latest hardware system V0.4.5.1, professional and stable.

【Frequency Range】ULTRA tinysa has 100kHz to 5.3GHz ultra-wide measuring frequency range, spectrum analyzer for 0.1-800MHz. In Ultra mode, up to 0.1MHz-6GHz. It has 200Hz-850kHz RBW, adjacent signals effectively distinguished when RBW reach 200Hz, meet SSB two-tone test requirements, maximum width 850kHz, RBW implements fast scanning.

【Used As Signal Generator】It is 2 in 1 device, can be used as Signal Generator. Built-in calibration signal generator that is used for automatic self test and low input calibration. 100k-800MHz sine wave output; 800MHz-4.4GHz square wave output; 4.4GHz-5.4GHz mixing signal output.

This instrument has four interfaces: single point measurement, scanning, system information, correction and calibration.

The default boot into single-point measurement interface. Note: For the convenience of the user, each time calibration correction options will automatically change to the user calibration. Meanwhile, in order to ensure the integrity of the calibration, the calibration process, the automatic shutdown function fails, the consistent boot.

Startup and shutdown Hold down the CTRL key off press the power switch button.

【4.3 inch Touch Screen】This NanoVNA-F with 4.3inch IPS TFT LCD and resistive touch screen, which can measure S-parameter, voltage standing wave ratio SWR, phase map, group delay, Smith chart, DELAY, POLAR, LINEAR and so on.

【5000mAh Large Capacity Battery】Upgraded the large capacity 5000mAh / 3.7V lithium battery, longer standby time, and extended USB interface. Typically, it can be used as a mobile power source to charge Android or Apple phones when not in use. Support Chinese and English menu switching.

【Excellent Aluminium Housing】The RF front end is designed with a metal shield to make the S21's dynamic range better than 60dB over the entire frequency range. The aluminum housing protects the SMA head and reduces the interference of external electromagnetic waves on the instrument.

✅【2023 Upgraded TinySA Ultra】:This New Version V0.4.5.1 Spectrum Analyzer is developed by Hugen, with 4.0 inch 480 x 320 large touchscreen display, 100kHz to 5.3GHz widely measure range, with the new ESD protection function, the product has a higher anti-static level and a longer service life, and built-in 32Gb micro SD card, can directly record data to the card ,which is convenient for your data sharing and storage.

✅【Frequency Range】:Compared to the tinysa (100kHz to 960MHz), the upgraded tinysa ULTRA has 100kHz to 5.3GHz ultra-wide measuring frequency range, spectrum analyzer for 0.1-800MHz, with Ultra mode up to 0.1MHz-6GHz.Switchable resolution band pass filters for both ranges between 200Hz to 850kHz. Color display showing 450 scan points covering up to the full low or high frequency range. Faster and more accurate measurement performance, you can easily cope with measurement testes in various fields.

✅【2 in 1 Multifunctional Frequency Analyzer & Signal Generator】:When not used as Spectrum Analyzer it can be used as Signal Generator,with sine wave output between 0.1-800MHz or square wave or dual tone output up to 4.4GHz.Built-in calibration signal generator that is used for automatic self test and low input calibration.

1.5 GHz Real-Time Spectrum Analyzer w/10MHz RTBW - VNA Capable

Real time spectrum analyzer with vector network analysis

Frequency range: 9kHz to 1.5 GHz

Frequency Range from 9 kHz up to 3.2 GHz

10 Hz Minimum Resolution Bandwidth

Min. -161 dBm Displayed Average Noise Level (Typ.)

[RF Demo Kit]: RF demo kit RF test board demo calibration board for learning vector network analyzer, antenna analyzer test calibration learning

[18 Functional Modules]: The board is totally integrated with 18 functional modules; Each module is well selected of high quality and great reliability

[Convenient and Portable]: Equipped with 2 pcs of UFL patch cord for convenient use; The board is small and light, suitable for carrying with

2.4 GHz and 5 GHz Spectrum Analyzer views all interference including ZigBee, Bluetooth, Baby Monitors, etc

Android, iOS, Mac, PC Supported

Scan and Troubleshoot Wi-Fi

3.2 GHz Spectrum Analyzer

As of 4/1/2017 - Includes Preamplifier OptionPA-DSA832Standard(Previously a $599 add on)

DSA832E Spectrum Analyzer, 9 kHz to 3.2 GHz

Troubleshoot and analyze all your Wi-Fi issues - displays everything in the 2.4 Ghz and 5 Ghz spectrum, including Zigbee, so you can isolate problems that impact your network

Use the WiFi Hound during your initial site survey at a new location to quickly optimize channel and power settings on your Access Points

Designed for live environments with an adjustable refresh rate

Spectrum Analyzer, 9kHz to 1.5GHz with preamplifier

2012 top selling unit

9 kHz to 1.5 GHz Frequency Range