Best Fulton in 2026

Heavy Duty Nylon web winch strap with hook

2 inch width, 20 foot length

10,000 pounds maximum working load

When setting up our dust collection or filtration systems we tend to have a lot of “moving parts” during this process and trying to figure out what type of line, piping or hose to use can be challenging. Dust collection hoses need to be not only long enough, but it must be durable, flexible and sturdy enough, so it won’t completely collapse in use. It must also perform under the constant use and abuse of an everyday workshop environment. This PVC hose checks all of those boxes and more!

Typically, PVC hose works best as a dust collection hose for woodworking applications where dust and chips from cutting, milling or sanding wood is a problem. This heavy-duty hose will stand up to small and large chunks of wood without getting punctured as well as handle the smallest of saw dust without leaking. PVC hose can be used as a primary line or can be plugged into and out of machinery as needed.

PVC Hose (depending on diameter) can be used with dust collectors, shop vacuums, industrial vacuum systems, lawn tractor leaf catchers and a whole lot more! Simply make sure both ends of the hose are secured with hose clamps and your ready to go. The PVC hose flexes enough to weave in and out of shop machinery or table legs without kinking. Its also sturdy enough that it won’t flatten out when the dust collector is turned on. The hose has a compression ratio of 3: 1.

We’ve all used those pesky and irritating horse hair acid glue brushes to apply white school glue or yellow wood glue only to find out the bristles don’t hold very well and the glue coverage is minimal. Not only that, we tend to keep buying more and more and more of these brushes just to use them once and throw them away.

Introducing the the Sili Brush! This silicone glue brush allows you to apply yellow wood or white school glue quickly and easily with the SILI Brush non-stick glue brush. The SILI Brush is designed to be used over and over again without having to purchase extra brushes like you would with typical tin acid or flux applicator brushes. The silicone bristles make applying glue and cleanup of the brush a breeze.

Once you finish applying glue, simply rinse the brush head off with warm soap and water and you are ready to re-use the SILI Brush again after it dries. Another way to clean the Sili brush is to let the glue dry over night on the brush tip and then peel the glue right off without damaging the brush. It’s perfect for when we are in a rush or simply just forget to clean the brush. No more throwing away brushes and no more buying huge multipacks.

Applying veneer, laminate or even wall coverings usually requires some tools that you may not find in your neighborhood big box store or even at a local mom and pop hardware store. The Fulton J-Roller is one of those items and is the ideal tool for applying pressure to your sheet or paper goods to ensure proper adhesion to your work surface.

When applying veneer on wood for example, you generally need to exert a good amount of even downward pressure on the veneer sheet or roll. To do this, we could use a flat bar of some sort, but that generally won’t be even enough and can’t get into the slight undulations of the wood surface. The Fulton J-Roller is the perfect width to properly work the veneer for proper adhesion.

A full 12” long, the J-Roller is the perfect length to handle most any project where you need to apply sheet goods to another surface. The roller is made from a firm, non-marring, textured rubber material that helps you apply pressure where it is needed. The roller wall is about 3/8” thick so it will stand up to the rigorous chore of applying pressure to your sheet goods.

1, 400 lb. capacity winch designed to meet your toughest pulling demands

features an efficient gear ratio, full-length drum bearings, oil-impregnated shaft bushings, and an 8 inch 'comfort grip' handle for ease of cranking

high-carbon steel gears for superb strength and long-term durability

Bolt-On Swivel Tongue Jack, 1500 lbs. capacity, with an additional 2" of travel

Bolt-Thru mount with minimal deflection and maximum support

6" Dual Wheel, 1/2" swivel pull pin

We have all been in a situation where we need to quickly turn the power off on our router table or contractor table saw and both of our hands are a bit pre-occupied. Reaching down and underneath your router table or contractor table saw to try and locate the power switch can be very cumbersome as well as very dangerous while your feeding stock through.Many router table setups don’t even have an external power switch separate from the router itself.

With this uniquely designed and easy to locate Paddle Button Stop Power Tool Switch you can simply bump the large stop sign paddle with your knee or hip to shut the power off. That means both of your hands can stay engaged on the project while you bump the power off with your hip or knee. A large green START button is always visible on the top side of the paddle. Simply push the START button to power on.

Install the switch near or at hip level or in a position that you will be able to bump it when needed. The switch comes with installation hardware and can be mounted to most any type of material. The unit has two cords. The heavy duty female cord is 18” long and designed to accept the power source plug from your power tool. The heavy duty male cord is approximately 66 inches long and is used to plug the switch unit into your standard wall outlet.

Corrosion resistant aluminum frame and handle

Center drive enclosed ratchet system with a user-friendly pull-turn knob to engage ratchet plunger pin

Left or right handed handle attachment and 2-position handle adjusts from 6 inch to 9 inch

Strap retracts for easy storage and no tangling

Easy bolt on function; hardware included

Zinc housing and hardware

1,600 pounds capacity

Corrosion resistant aluminum frame and handle

Dual gear drum operates smoothly

Outer tube diameter 2.25 inches - Inner tube diameter 2 inches

5,000 lb rating

15 inches of travel

Bolt-On Swivel Tongue Jack, 1500 lbs. capacity, with an additional 2" of travel

Bolt-Thru mount with minimal deflection and maximum support

Sturdy 8" spoked wheel, 1/2" swivel pull pin ; Handle Style: Sidewind

NO MORE TOOLS! – Set your tools aside when installing your ductwork or hose with these handy, easy to tighten hose/duct clamps. Place the clamp where its needed then simply turn the key to loosen or tighten them.

LARGE EASY TO TURN KEY - The easy to turn and easy to see blue key is made from a strong and durable polymer. The key is designed to make the securing and un-securing of hose much easier on the knuckles. No more knuckle busting flat head screw drivers or tiny socket wrenches. Simply to turn the key clockwise to tighten, counter clockwise to loosen.

OFTEN USED IN THESE APPLICATIONS – These unique clamps are typically used in securing duct work, dryer vents, dust collection hoses, piping, large cable, pvc tubing and more. Ideal for use in automotive, industrial, mechanical, agriculture, boat/marine, shield, recreational vehicles, household and more. Works for both indoor or outdoor use.

NO MORE TOOLS! – Set your tools aside when installing your ductwork or hose with these handy, easy to tighten hose/duct clamps. Place the clamp where its needed then simply turn the key to loosen or tighten them.

LARGE EASY TO TURN KEY - The easy to turn and easy to see blue key is made from a strong and durable polymer. The key is designed to make the securing and un-securing of hose much easier on the knuckles. No more knuckle busting flat head screw drivers or tiny socket wrenches. Simply to turn the key clockwise to tighten, counter clockwise to loosen.

OFTEN USED IN THESE APPLICATIONS – These unique clamps are typically used in securing duct work, dryer vents, dust collection hoses, piping, large cable, pvc tubing and more. Ideal for use in automotive, industrial, mechanical, agriculture, boat/marine, shield, recreational vehicles, household and more. Works for both indoor or outdoor use.

Transparent high grade PVC

Length 94cm

Span when open approx 89cm

NO MORE TOOLS! – Set your tools aside when installing your ductwork or hose with these handy, easy to tighten hose/duct clamps. Place the clamp where its needed then simply turn the key to loosen or tighten them.

304 STAINLESS STEEL HOSE CLAMP- The 2 ½” diameter large hose duct clamp (including the housing, the band and the internal screw are made from premium 304 stainless steel. This makes the clamp strong, durable and rust resistant which makes it ideal for many applications in the shop or around the home.

LARGE EASY TO TURN KEY - The easy to turn and easy to see blue key is made from a strong and durable polymer. The key is designed to make the securing and un-securing of hose much easier on the knuckles. No more knuckle busting flat head screw drivers or tiny socket wrenches. Simply to turn the key clockwise to tighten, counter clockwise to loosen.

Bolt-On Swivel Tongue Jack, 1200 lbs. capacity

Bolt-Thru mount with minimal deflection and maximum support

Sturdy 6" Poly wheel, 1/2" swivel pull pin

3,200 pounds capacity, One-handed system shifts from high to low speed

Dual gear drum operates smoothly

One piece corrosion resistant aluminum frame and one piece corrosion resistant aluminum handle

Sometimes bigger is better and when it comes to drilling or boring into thick material, bigger is definitely better. Introducing the Fulton high speed steel extra long brad point drill bit set. Each bit measures around 12 inches in total length to provide you with enough drilling length to tackle most any project you can throw at them.

Many times when working around the house or out on the job site, we come across a situation where we need to drill through thicker material like a 6 x 6 or 4 x 4 when building things like an privacy fence or even rough building applications. These Fulton extra long brad point drill bits are perfect for these situations!

Made from high speed steel, these bits are ideal for many different project types and materials. Drill into MDF, 4 x 4’s, 6 x 6’s, PVC, Resin’s, Composites, Plywood and more. Since each bit has a sharp (brad point) tip, it is recommended that you do NOT use these bits to drill into metal objects.

Drilling with forstner bits to achieve a flat bottom hole or to start a deep hole turning project like on a larger vase or vessel is essentially impossible with a standard length forstner bit. To remedy this issue we have developed a heavy duty steel extension that allows you to secure a 3/8 inch shank forstner bit into the end collet.

The forstner bit extension gives you additional 5-5/8 inches of reach to bore deeper into your projects. This will help you create larger diameter starter holes or help when you need to drill in just a little further than the standard bit length will allow. The extension can be used with forstner bits on drill presses, lathes with a drill chuck installed (drill chuck not included) or with a power drill.

One of the most common uses for the forstner bit extension is for woodturners who need to bore out starter holes on larger vessels. However, the extension works exceptionally well for projects like salt shakers, pepper mills or even wood turned beverage mugs. Contractors use the extension when they need to bore deep holes for running cables or wires and they also use it for joining larger timbers.

3/16 inch x 25 foot Galvanized Cable with Hook

4,200 pounds breaking strength

Package Dimensions: 25.4 L x 4.572H x19.304W(centimeters)

Push blocks are designed to be one of your essential safety devices to help provide protection and prevent your fingers from getting too close to cutters or blades on a router table, band saw, shaper or a jointer. Push blocks work well in multiple situations throughout your woodworking projects and are intended to be used any time your fingers are close to being in harms way.

Push blocks can be used one at a time like when feeding stock through your router table with a fence or you could use two at a time for extra downward pressure like when you would feed stock through on a jointer. They also work well on band saws for re-saw applications and can also be used on shapers much in the same way they are used on router tables.

This Push Block has been intentionally made in a bright SAFETY ORANGE color for high visibility when in use. This provides the user the ability to see exactly where their hands are at during the cutting or milling process. The bright SAFETY ORANGE color also allows you to easily find the device when it’s not in its normal location.

Bolt-On Swivel Tongue Jack, 1200 lbs. capacity

Sturdy 6" Poly wheel, 3/8" swivel pull pin

Hardware included to mount up to a 3" x 5" trailer frame

Finally! A set of contours, angles and pads that work for inside, outside, flat, curved, small and tight areas all in one convenient package! The non-slip rubber pad prevents abrasive slippage and hand fatigue. This set is perfect for woodworkers, auto body, metal work, arts, crafts or even around the house.

These 11 grips with 21 different profiles will tackle most any sanding project you may come across. Designed to work with standard 9” x 11” sanding sheets or pre-cut sandpaper sheets (included). This set is a set of sanding pads that no one should be without.

The Contour Sanding Grip pads are double-ended to make it super easy to sand convex or concave surfaces. Each pad has a convex profile at one and a concave profile at the other along with a narrow flexible section in the middle that can be used for sanding

The Fulton Miter Gauge is a high quality, well thought out and economical solution for your table saw cross cutting needs.The Aluminum Miter fence is equally well thought out with its 45 degree ends for unsurpassed workpiece support and its ability to mounted to most any miter gauge. Also included is a handy aluminum flip stop for repetitive angled cuts on your table saw. Together these three items are the perfect compliment to each other for your table saw cutting needs.

The .200” thick, adjustable, solid aluminum head is machined with 13 positive stop holes. 1 hole is at 90 degrees while the 6 holes on both sides are at 22.5, 30, 45, 60, 67.5 and 90 degrees. The positive stops are perfect for many woodworking projects as they are the angles that are typically used.To adjust the head you simply loosen the post knob handle, pull the spring loaded indexing pin outward, rotate the head to the desired position, release the pin and lock into place.

The head is mounted to a solid steel miter bar that measure 18” in length and is .354” thick by .730” wide. Standard miter slots are 3/4” x 3/8” with a 1/8” “T” slot (slight variances from brand to brand) running the length on the bottom of the slot. The steel miter bar is equipped with a metal, removable retaining disc that measures 7/8” in diameter and is just shy of 1/8” to fit into to the “T” slot to prevent accidental lifting when feeding your stock through.

When setting up our dust collection or filtration systems we tend to have a lot of “moving parts” during this process and trying to figure out what type of line, piping or hose to use can be challenging. Dust collection hoses need to be not only long enough, but it must be durable, flexible and sturdy enough, so it won’t completely collapse in use. It must also perform under the constant use and abuse of an everyday workshop environment. This PVC hose checks all of those boxes and more!

Typically, PVC hose works best as a dust collection hose for woodworking applications where dust and chips from cutting, milling or sanding wood is a problem. This heavy-duty hose will stand up to small and large chunks of wood without getting punctured as well as handle the smallest of saw dust without leaking. PVC hose can be used as a primary line or can be plugged into and out of machinery as needed.

PVC Hose (depending on diameter) can be used with dust collectors, shop vacuums, industrial vacuum systems, lawn tractor leaf catchers and a whole lot more! Simply make sure both ends of the hose are secured with hose clamps and your ready to go. The PVC hose flexes enough to weave in and out of shop machinery or table legs without kinking. Its also sturdy enough that it won’t flatten out when the dust collector is turned on. The hose has a compression ratio of 3: 1.

We’ve all used those pesky and irritating horse hair acid glue brushes to apply white school glue or yellow wood glue only to find out the bristles don’t hold very well and the glue coverage is minimal. Not only that, we tend to keep buying more and more and more of these brushes just to use them once and throw them away.

Introducing the the Sili Brush! This silicone glue brush allows you to apply yellow wood or white school glue quickly and easily with the SILI Brush non-stick glue brush. The SILI Brush is designed to be used over and over again without having to purchase extra brushes like you would with typical tin acid or flux applicator brushes. The silicone bristles make applying glue and cleanup of the brush a breeze.

Once you finish applying glue, simply rinse the brush head off with warm soap and water and you are ready to re-use the SILI Brush again after it dries. Another way to clean the Sili brush is to let the glue dry over night on the brush tip and then peel the glue right off without damaging the brush. It’s perfect for when we are in a rush or simply just forget to clean the brush. No more throwing away brushes and no more buying huge multipacks.

If you own a table saw and you need to make a crosscut at any angle then you know how valuable a miter gauge can be. You may also know that the miter gauge that came with your saw is not terribly accurate or durable. Not to mention that the fit in the miter slot may not be all that great as well. The Fulton Miter Gauge is a high quality, well thought out and economical solution to your table saw cross cutting needs.

The .200” thick, adjustable, solid aluminum head is machined with 13 positive stop holes. 1 hole is at 90 degrees while the 6 holes on both sides are at 22.5, 30, 45, 60, 67.5 and 90 degrees. The positive stops are perfect for many woodworking projects as they are the angles that are typically used.

To adjust the head you simply loosen the post knob handle, pull the spring loaded indexing pin outward, rotate the head to the desired position, release the pin and lock into place by tightening the post knob handle. The aluminum head has two ¼” x ½” slots milled into it for mounting a miter fence if so desired. The slots are approximately 1-1/8” from the base of the miter gauge head.

Waterproof LED surface mount tail light

Wrap-around design eliminates the need for rear side marker/reflector

Plug-in 12" harness with 2-way flat connector and ring terminal ground wire

1, 800 lb. Capacity winch designed to meet your toughest pulling demands

Features an efficient gear ratio, full-length drum bearings, oil-impregnated shaft bushings, and a 10 inch 'comfort grip' handle for ease of Cranking

High-carbon Steel gears for superb strength and long-term durability