Best Micsig in 2026

Bandwidths up to 2.5MHz

Powered by USB, making measurement easier

Both automatic and manual zero adjustments are available

Automatically measures volts ac and volts dc with precise digital resolution

Displays resistance to 1000Ω

Easy and accurate OpenJaw current measurement

Efficient: The testo smart probe set offers precise measurements and calculations for heating and cooling systems, making it ideal for all HVAC/R contractors and technicians

Testo 605i: The thermohygrometer is equipped with a bendable probe head and thus achieves remote temperature measurements in rooms, ducts, crawl spaces and registers

Testo 115i: With a grip of up to 1.5”, the wireless thermometer provides quick and reliable temperature and flow and return temperature measurements of pipes

60A AC/DC Amp Clamp Probe

Use with most DMM

Zero/Calibration Function

〖Quick and Accurate AC/DC Amp Clamp Meter〗 is based on Hall Effect technology and is designed to be used in conjunction with multimeter for ac and dc current measurements.

〖Max. Jaw Opening〗The Clamp measures the AC current in a conductor up to 33mm without interrupting the circuit, Max. Conductor Size: ∅ 28mm.

〖Power/Low Voltage Indication〗When the battery's voltage is enough, the LED lights green. When the battery's voltage is less than about 7.5V, the LED lights red indicating that the battery is not high enough and should be replaced immediately.

Expands the measurement range to 2500A ac while providing increased display flexibility, ability to measure awkward sized conductors and improved wire access

CAT IV 600 V, CAT III 1000 V safety rating

7.5mm coil diameter allows measurement in tight spaces

TECPEL CA-60 AC / DC mA Current Clamp transmitter probe

The CP2100A Oscilloscope Probe has automatic and manual zero adjustment modes, it can also perform zeroing and demagnetization automatically or manually. Bandwidths up to 800KHz.

The split design makes the probe small and exquisite , easy to carry and use.

This CP2100A Current Probe can be powered by Oscilloscopes USB port and doesn't require any extra power supply.

To be used in conjunction with multimeter for ac current measurements.

Please note that : clamp only one conductor. It ONLY works with the multimeter which has the function of current signal input.

The conductor should be in the center of the jaws and should be perpendicular to the current probe.

[2 buttons] Clamp design and only 2 buttons make operation easy. 45 mm opening for measuring current without touching or interrupting the circuit. It comes with a test probe for convenient measurement.

[Measurement range] Measurement range: 600A DC / AC current. You can measure multimeter current and oscilloscope current waveform.

[High-quality material] This current probe clamp meter is made of high-quality material and is durable and durable. Customers can use it at ease.

Allows accurate measurement of currents from 100 mA to 1000 A rms, 5 Hz to 100 kHz without breaking into the circuit

A passive filter eliminates noise and ring on rapidly rising di/dt waveform, ensuring accurate screen displays

Connects directly to an oscilloscope through a reinforced coaxial cable and an insulated BNC connector

Bandwidths up to 2.5MHz

Powered by USB, making measurement easier

Both automatic and manual zero adjustments are available

¡¾High Performance¡¿The current clamp can take accurate current readings .The current clamps are the ideal tools to extend the current ranges of Oscilloscope tools.Support Auto zero at power on, relative zero correction function.It has Band wide up to 200KHz,support low battery indication .Adopt of amorphous alloy core, with high performance, low loss .

¡¾BNC connector¡¿The current clamp Multimeter features a BNC connector and can be plugged directly use. After connected well, switch the current clamp on (power LED should light) and then clamp the jaws around the current carrying conductor as shown. Typical Uses The AC/DC Current Probe simply offers the best value for money without compromising resolution.

¡¾Multiple Test Ranges¡¿The OWON CP-05+ current clamp is ideal for use with automotive oscilloscopes for measuring currents between 1 mA and 400 A. Various current test range, 4A, 40A, 200A, 200-400A test range are available.Low noise level, and high detection accuracy.

Higher Current Measurement: RQ-605A current clamp adapter is design for higer AC/DC current test range. It is able to up to 600A,which is the best partner for digital multimeters.

Great Probe of Digital Multimeters: We recommend RQ-605A use WapoRich multimeters such as 770D/ 770K/ 770S. With other brand, it is compatible with most multifunction testers with a sensitivity of 1 mV.

Improve Accuracy: Accuracy: ±(2.5% of rdg + 5digits), with an output voltage of 1 mV per amp and a standard 3/4 inch banana plug. The direction of the arrow on the right side of the clamp indicates the direction of the current( from positive to negative)

PREMIUM QUALITY AMORPHOUS ALLOY CORE ENSURES HIGH EFFICIENCY BUT LOW CONSUMPTION PERFORMANCE--Adopt of amorphous alloy core, with high performance, low loss

WIDER AND MORE VARIETY TEST RANGE--Various current test range, 4A, 40A, 200A, 200-400A test range are available

HIGH BANDWIDTH AND LOW BATTERY INDICATION OFFERS EASIER OPERATION--Band wide up to 100KHz, low battery indication

【Multiple Test Ranges】The OWON CP-05+ current clamp is ideal for use with automotive oscilloscopes for measuring currents between 1 mA and 400 A. Various current test range, 4A, 40A, 200A, 200-400A test range are available.Low noise level, and high detection accuracy.

【High Performance】The current clamp can take accurate current readings .The current clamps are the ideal tools to extend the current ranges of Oscilloscope tools.Support Auto zero at power on, relative zero correction function.It has Band wide up to 200KHz,support low battery indication .Adopt of amorphous alloy core, with high performance, low loss .

【Easy to Use】The current clamp has range selection settings, set by a slider switch on the handle of the probe. In use there is no need to break into the circuit or disturb the isolation as the opening jaws simply clamp around the current carrying conductor. No electrical contact is required. These current clamps have been designed for use with oscilloscopes.

Current probe is based on hall effect technology

Use in measurement of both DC and AC current

It may be used in conjunction with oscilloscopes and other suitable recording instruments for accurate non-intrusive current measurement

Package Dimensions: 6.77 L x 6.57 H x 5.47 W (inches)

Package Weight: 2.2 pounds