Best Bushing Tools in 2026

Hornady Lock-N-Load Die Bushings – The Lock-N-Load bushing system will forever change the way you switch from one caliber to another. Lock-N-Load technology allows you to change dies and start loading another caliber in a matter of seconds. Includes 2 die bushings

Maximize Reloading Time – Quickly and easily change from one die to another with a simple twist. Item number: 044094

Positive Locking Action – Holds the dies in perfect alignment. Compatible with all Hornady Reloading Presses

Full magnetic ring for a more securely retained spark plug compared to other magnetic and rubber bushing style sockets

Universal swivel design for increased access with minimal outside diameter sockets for tight cylinder head clearances

3/8” drive 6-point sockets in 9/16” (14mm) x 6”, 5/8” (16mm) x 6”, 5/8” (16mm) x 10”, and 13/16” x 6”

SERVICE YOUR VEHICLE: Keep your suspension system running smoothly by replacing worn ball joints with the ABN Ball Joint Removal Tool and Bushing Press Kit; 10 piece ball joint tool kit includes receiver tubes and adapters to work on most press-fit upper and lower ball joints

REMOVE PARTS EASILY: Remove worn, rusted, and corroded parts with this ball joint remover kit; Works as a ball joint separator tool, u joint press, tie rod end remover tool, and suspension bushing removal tool

PACKAGE CONTENTS: Ball joint removal kit includes (1) C-frame ball joints press and forcing screw, (3) installation adapters with cups, (3) removal adapters with cups, (3) receiver tubes (2.75 x 3 inch, 2.25 x 2.5 inch, and 1.75 x 2 inch) this is impacted rated

EASILY REMOVE YOUR 1911 BARREL BUSHING: Put the bushing wrench flat on the table so the rubber ring grabs the table, then simply twist. It makes taking apart your 45 a breeze!

KEEP YOUR RECOIL SPRING FROM FLYING: When you twist, the tool captures your 45’s recoil spring plug so it doesn’t go flying across the room.

KEEP YOUR GUN LOOKING GOOD: The non-marring, engineering-grade resin won’t mar or damage your favorite gun’s parts plus the 2018 model is tougher than ever before.

With the 16002 you can safely and easily remove brake anchor pins and bushings on virtually all 16-1/2” S-Cam trailer and tractor “Q” brake systems in minutes.

Application: Commonly found on class 6-8 transportation trucks and equipment. (For use with Kenworth, for use with Peterbilt, for use with Freightliner, for use with Mack, for use with Volvo, etc.). In the event you are servicing a stamped spider, a punch and chisel may be required to remove the bushing.

The 16002 has a rigid C-frame with 10-ton capacity, and as always, this tool is manufactured from high-grade steel for strength and durability. The compact design enables the operator to service brake anchor pins and bushings while the hub and dust shield remain on the vehicle. Don’t waste your time replacing rusted, seized or broken dust shield bolts; with the 16002, you need only focus on the task at hand.

✅ APPROPRIATE SIZE: You may create your own unique bushing driver with the Shankly bushing removal tool kit, ensuring that it is always the appropriate size for the task. You may select the ideal combination for each bushing using these bushing tools

✅ COMPLETE SET: The discs of this bearing press kit are available in 1mm increments from 18mm to 65mm, and 74mm. A 180mm handle that connects rapidly to all of the discs through a 12mm shaft and screw makes the wheel bearing driver set complete and efficient

✅ INTERCHANGEABLE DISCS: Extensively tested and proven to do what it was designed to do. The 50 discs of this press tool kit can all be used interchangeably, giving you several sizes which provide the user with an amazing 2,450 different variations in one set

These feed-through bushings seal wall openings and protect cables from harm and abrasion damage

Weatherproof & “varmit-proof” when used in conjunction with a silicone seal (sealant sold separately)

Crafted out of ABS plastic, UV-Stabilized construction & Available in Black and White (sold separately)

APPLICATION： The Ball Joint Press Set Ball Joint Tool / Bushing Removal Tool with 4WD Adapter can effortlessly remove press fit parts including ball joints, U-joints, brake anchor pins, and more on most 2-wheel drive (2WD) and 4-wheel drive (4WD) vehicles without removing the control arm from the vehicle

MATERIAL： Heavy-duty forged steel with black-oxide finish on adapters for maximum strength and longevity that resists rust and corrosion.

COMPATIBLITY： The Ball Joint tool compatible with most American domestic and imported 2-wheel drive (2WD) and 4-wheel drive (4WD) cars and light pickup trucks that have press-fit type ball joints

1.ESSENTIAL TOOL FOR BALL JOINT SERVICE - Use the ORION MOTOR TECH Ball Joint Press Set Ball Joint Tool / Bushing Removal Tool with 4WD Adapter to effortlessly remove press fit parts including ball joints, U-joints, brake anchor pins, and more on most 2-wheel drive (2WD) and 4-wheel drive (4WD) vehicles without removing the control arm from the vehicle.

2.PROFESSIONAL GRADE QUALITY AND DURABILITY - Off road weekend warriors, novices, and professional mechanics trust the ORION kit because ORION MOTOR TECH sources the highest quality components from around the world. Constructed from heavy-duty forged steel with black-oxide finish on adapters for maximum strength and longevity that resists rust and corrosion.

3.UNIVERSALLY COMPATIBLE WITH A WIDE RANGE OF VEHICLES - Fit most American domestic and imported 2-wheel drive (2WD) and 4-wheel drive (4WD) cars and light pickup trucks that have press-fit type ball joints, include 4-wheel drive (4WD) adapter that allows service for 1967 thru current 1/2 and 3/4 ton 4WD vehicles having the Dana 30 or 44 front axle (compatible with Ford, GM, Dodge, IHC and Jeep vehicles).

Inner Diameter:30mm/1.18";Screw:14mm/0.55".

Magneto flywheel pulle replacement for 4-Stroke 49cc 50cc 70cc 100cc 125cc 150cc Motorcycle Scooter.Not replacement for 2022 BD125-10.

Install the special nut of the flywheel puller in the threaded hole of the flywheel bushing,and the special screw is placed on the center hole of the crankshaft. Rotate the screw to increase the force on the crankshaft,so that the flywheel can be separated from the crankshaft.

Complete standard and metric bushing adapter set with 30 adapters from 10mm & 3/8" up to 1-3/8" & 42mm in one set. 3 strong alu handle with diameter 0.4”, 0.6” & 0.8”.

SAE adapter: 3/8"x7/16", 7/16"x1/2", 1/2"x9/16", 9/16"x5/8", 39/64"x11/16", 5/8"x3/4", 11/16"x13/16", 47/64"x7/8", 13/16"x15/16", 55/64"x1", 15/16"x1-1/16", 1"x1-1/8", 1-1/16"x1-3/16", 1-3/16"x1-5/16",

Metric adapter: 10-12mm, 12-14mm, 14-16mm, 15-17mm, 16-18mm, 18-20mm, 20-22mm, 22-24mm, 25-27mm, 28-30mm, 30-34mm, 32-36mm, 35-40mm, 38-42mm

EFFORTLESSLY REMOVE POWER STEERING LINES: The ABN Automotive Power Steering Pump Pulley Remover Installer Tool Kit is a disconnect toolset that releases and installs the power steering line from the pump on most American domestic vehicles such as 1989 to current GM pickups 1T, 1/2T, and 3/4T; Fits pulley hubs with diameters of 1-1/8 inch , 1-1/4 inch , 1-5/16 inch, and 1-3/8 inch

EASY TO USE: We recommend using lubrication on the tools before use; Place the threaded screw in the center of your pulley with the half-moon clamp shells and lip retaining ring surrounding it, then place the grabber nut center piece with a die on top, tightly screw the threaded stud onto the center of the end of your puller nut, and then use a ratchet, crescent wrench, or air gun with socket to loosen and remove

FITS YOUR VEHICLE: For use on Saginaw, Thompson, and Ford C111, C2 power steering pumps found on Ford, GM, and Chrysler vehicles; Two included screws for use on most Ford, Chrysler, GM, and Volkswagen VW power steering pulleys GM 3.1L, 3100, 3400 and 3800 V6 Engines or 2.3lL QUAD 4 four-cylinder engine, Ford 4.6L, 5.4L and 5.8L modular V8 engines, and more; Pulls pulleys on GM belt-driven vacuum pumps and press-on water pump pulleys on GM V6 engines

SLIDE HAMMER DENT PULLER TOOL: The ABN Slide Hammer Car Dent Removal Tool and Wheel Bearing Puller Set is designed for loosening and pulling tight parts from a vehicle, but also makes a great auto dent removal kit; The car dent remover kit contains a 4.8-pound (2.2 kg) body hammer with multiple attachments making the tool incredibly versatile

AUTO BODY REPAIR TOOLS: Often, slide hammer bearing puller kits are body shop tools that are used to aggressively remove tightly jammed parts or dents; Slide hammers consist of a long metal shaft with an attachment point at one end, a heavyweight that slides along the shaft, and a handle with a stop on the opposite end; This hammer tool slide kit includes 2 jaws and 3 jaw internal and external pullers, rear axle bearing puller tool, locking plier adaptor, puller hook, and auto dent puller tool

EASY TO USE: To use, first attach the car dent puller kit to the part you wish to remove, then yank the weight towards the handle to give an extra snap of weight to the stuck part while you pull on the T-handle; The force transfers to the shaft, pulling the attached end and part in the desired direction; Repeat action until the hub or bearings are removed; Lubricants can be beneficial for some tougher projects

No need to remove the bearing hub assembly just to replace the pins and bushings

Works on 16-1/2" S-Cam trailer and tractor Q brake systems

Special tooling and our C-Frame press get you past the hub assembly

Bushing driver tool set allows you to build your own custom bushing driver. Choose the required size and assemble your drive tool.

This bearing and seal driver set can remove or install bushings that are flush with the housing, ideal for removing seal, bush or bearing job. All 50 pieces are interchangeable with each other so you get 2450 different size variations

The discs goes from 18mm (25/32") all the way to 65mm (2-9/16") in 1mm increments plus (2-29/32") 74mm. All discs are connected with a 12mm shaft and screw which quickly connects to a 180mm 7-1/2" handle

Great Compatibility — Fit for GM 700R4 (700-R4) (4L60) (4L60E) (4L65E) transmissions.

Include — 12 Bushing Drivers (#61-71) and one Driver Handle. Each part is manufactured to OEM specifications and testing.

Perfect Design — Replacement for Atec Trans-Tool K&K OTC Kent-Moore SPX T-0220, T-0220-700R4, SKU311. More efficient and easy removal and instalation of bushings on all the above automatic transmissions to save your time and money.

Inner Diameter:27mm/1.06";Screw:14mm/0.55".

Magneto flywheel pulle replacement for 4-Stroke 49cc 50cc 70cc 100cc 125cc 150cc Motorcycle Scooter.Not Replacement for Pro-X 150 go cart,G310 R.

Install the special nut of the flywheel puller in the threaded hole of the flywheel bushing,and the special screw is placed on the center hole of the crankshaft. Rotate the screw to increase the force on the crankshaft,so that the flywheel can be separated from the crankshaft.

【SUPERIOR VERSATILITY】Includes 9 different size collars/discs (metric): 39.5, 44, 50, 59, 63, 64.5, 72, 76, 81mm, Ideal for removing or installing wheel bearing race and seals on most cars, vehicles, trucks and SUV without damage to axle housing.

【PREMIUM MATERIAL】Constructed from high quality high-toughness aluminum for long durability and good protection to axle housing, won’t mark the bearings during use. Anodized finish for anti-rust and anti-corrosion, extend tool’s service life even further.

【SOLID DRIVER】Includes a well manufactured aluminum driver (135mm). The anti-slipping knurled handle provides comfortable grip, makes pounding out /in easier, ensures safety during operation.

For use on BMW E36 E46 Chassis

Designed to remove the press fit the solid metallic rear suspension bushings (bushes/joints) located in the bearing carrier

Allows removal and installation of rear outer ball joint

Used in tailstocks to secure pen blanks on the mandrel

Eliminates damaged mandrels and out-of-round pen blanks by putting pressure directly on the pen bushing, not the mandrel

Adapts to almost every mandrel with a shaft diameter of .245" (6.22mm) or smaller; mostly commonly used with 7mm mandrels

✔【Direct use of】：In automotive bushing removal or installation work, we must often struggle with the use of bushing drive tools because the working environment in which bushing drives are used is often smaller than we think. 29090 Pneumatic Bushing Drive is an all-around tool, streamlined, inexpensive option for removing and installing 1-3/8" anchor pin bushings and stuck anchor pins on trucks and trailers,. and allows direct drive of the bushings without the need to remove the wheel assembly.

✔【High quality and method】 : The use of high quality reinforced materials, 11-1/2" long driver that allows bushings to be driven straight without removing the hub assembly. Double-sided cone snaps onto driver to drive out and install bushings. Use flanged end to install and tapered end to remove. Also removes truck leaf spring bushings.wear and corrosion resistance, long service life, so that it has a longer peak work rate, I believe it can make your work more relaxed

✔ 【package content】: 29090 pneumatic bushing drive a set

This 12 piece bushing driver kit is for the 700R4 (700-R4) (4L60) (4L60E) (4L65E) transmissions.

Bushing Driver Handle Included

Includes 12 Bushing Drivers and one Driver Handle.

Simple solution for the beginner or Pro

Simple reloading tool

Powder bushing

Includes One Mercedes Benz Bushing Remover/Installer

Designed to Remove and Replace Metallic Bushings on Mercedes Rear Axles

Services Almost All Mercedes Passenger Cars from 1984 and Up

Adjuster Plug Seal

Power Cylinder Seal

Control Valve Seal

【Applicable】Rear axle ball joint bushing removal tool kit designed to installation and remove the press fit the solid metalic rear suspension bushings (bushes) / ball joints in the bearing carrier. Features a design that allows replacement of the rear axle carrier Ball Joint with the carrier in place,avoids significant disassembly of suspension and driveline components. Designed for BMW Series 5 and Series 7.

【Suitable】BMW Engine series: E38, E39, E52, E60, E61, E63, E64, E65, E66, E67, E70. Models: BMW 528i, 528i Wagon, 540i, 540i Wagon, 525i, 525i Wagon, 530i, 740i, 740il, 750il, and all 1995 - 2003.

【Packing】Comes within a blow moulded case.

Master Bushing Tool Set ---- deluxe custom driver kit, assist in the bearing race and seal replacement on your car, truck transmission, axle, wheel hub when installing new bearing seal back into your vehicles

Universal Compatibility ---- our bearing and seal driver set has 50 interchangeable discs, giving you an amazing 2,450 different variations due to each of the 50 discs being interchangeable with each other. The discs go from 0.7 inches all the way to 2.55 inches in 1mm increments plus 2.9 inches. All discs are connected with a 0.47 inches shaft and screw which connects to a 7.08 inch handle, making the wheel bearing driver set complete and effect.

Heavy Duty and Durability ---- heavy-duty carbon steel construction; black anodic oxidation for ultimate anti-rust performance, these components will stand up to heavy use and accidental drops. Perfect for off road weekend warriors, novices, and professional mechanics.

Save time by not removing components and using a conventional press

Allows quick R and R of suspension bushings

Comes with 22 cups and receivers for 100's of size combinations

WIDE APPLICATION: KOOPOOL Master ball joint press kit Includes 21 parts with multi-size adapters, versatile for removing and installing press-fit parts like upper and lower ball joints, brake anchor pin and U-joint on most GM, Ford and Dodge 2- and 4-wheel drive pickups, vans and SUVs from 1997 to present without removing the control arm from the vehicle

PRODUCT FEATURE: Ball joint press set ball joint tool / bushing removal tool Includes wealth of removing/installing adapters, receiving tubes and receiving/installing cups, removes ball joints, U-joints and brake anchor pins on domestic and imported 2-wheel drive and 4-wheel drive vehicles easily. The adapters are designed with specialized cut-outs to fit or maneuver around obstructions, serve perfectly for vehicles having the Dana 28, 30, 35, 44, 60 axles

HIGH DURABILITY: C-frame press is made of heavy-duty forged 20# carbon steel for ultra strength and high-intensity use. All removing/installing adapters, receiving tubes and receiving/installing cups are black oxide finished to resist rust and corrosion, extend its service life. The premium material makes this tool a must have for whether off road weekend warriors, novices, or professional mechanics

【Ideal for】 The Rear Trailing Arm Bushing Remover Tool is used for replacement of the rear trailing arm bush (moveable metal suspension pieces on the rear of your car that the wheel, brake, and hub connect to) on your vehicle; Removal and installation of the new bush to Rear Trailing arm without damage to the ABS sensor cable.

【Applicable】Fit For Honda or Acura vehicles with trailing arm bushings; Fit for Honda – Fit for Civic 1988-2000, Fit for CRV 1997-2001, Fit for CRX 1988-1991, Fit for Del Sol 1993-1997 and Fit for Acura – Fit for Integra 1994-2001, Fit for Integra 1990-1993

【Easy to Storage】Rear trailing arm bushing tool comes with a premium well-organized box for easy storage and transport. The tool is stored safely in a packaged case that can withstand high-strength extrusion.