Best Rockford Fosgate Multichannel Amplifiers in 2026

650 W MAX Power @ 2 Ohm x 4 Channels

325 W MAX Power @ 4 Ohm x 4 Channels

1300 W MAX Bridged Power @ 4 Ohm x 2 Channels

Includes: Amplifier. Birth sheet with tested power. Owner’s manual. Mounting Screws. Warranty.

Features: Rockville dB45 3200 Watt/800 Watt Dyno-Certified RMS 4 Channel Amplifier Car Stereo Amp, Loud!!.

Dyno Certified RMS Power Ratings: (Certified Dyno Test / Less than 1 % THD) (Use these ratings when comparing with top brands such as Kicker, Rockford Fosgate, etc). - 2 Ohm: 200 Watts x 4 Channel <1% THD+N . - 4 Ohm:135 Watts x 4 Channel <1% THD+N. - 4 Ohm Bridged: 400Watts x 2 Channel<1% THD+N.

The Punch P400X4 is a 400 watt 4-channel amplifier (2.38” x 7.76” x 11.03”) is perfect for a 4-way full-range system or a 3-way system having a front stage with subwoofers on the rear channels

Versatile multi-channel design is a perfect choice for virtually any vehicle (RMS Power Output: 50 Watts x 4 @ 4-Ohm OR 100 Watts x 4 @ 2-Ohm OR 200 Watts x 2 @ 4-Ohm Bridged)

RCA inputs can accept both Hi and Low level audio signals without the need of a signal converter

Competition Grade Class D MOSFET Power Amplifier

Peak Power at 1 Ohm: 5, 400 Watts | RMS Power at 1 Ohm: 3, 500 Watts

Stable at 1 ohm | Remote Subwoofer Level Control Included

Bridgeable

Variable input voltage

QTD (Quick Thermal Dispersion) technology heat sink

This part requires programming and/or special setup procedures. GM Service Information describes the procedures and special tools needed to ensure proper operation in the vehicle

Helps provide a wonderfully rich listening experience in your vehicle

Some GM Genuine Parts may have formerly appeared as ACDelco GM Original Equipment (OE)

HUGE POWER IN A SMALL PACKAGE - 3,000 Watts gives you all the power you need tucked away and out of sight, keeping your vehicle looking clean and neat.

WIDE RANGE OF APPLICATIONS - Ranging from 1-4 ohms, this amplifier will allow you to use a variety of speakers for your specific application. Never again will you need to worry about having the right amp for the job.

BASS KNOB INCLUDED - The Candy XXL1B amplifier comes with a remote bass knob included. Always have control over the bass levels depending on what genre music you're listening to.

Class AB

70W x 4 CEA 2006 RMS @ 4 Ohms

160W x 2 RMS @ 4 Ohms

Picasso Nano Series 4-Channel Class D Car Amplifier

RMS Power Rating: 4 ohms: 140 watts x 4 chan. / 2 ohms: 250 watts x 4 chan.

Max power output: 500 watts

1600W Maximum Power Full-Range Amplifier With Bluetooth

Optimized 150-watt RMS output and a max power output of 1600 watts, you can give your music a huge boost in power that will have you and your passengers partying while on the road

This slim amplifier fits perfectly into any trunk so you can easily connect it to your stereo system

AUDIO EVOLUTION: This car speakers amp features regulated MOSFET Pulse Width Modulated that maintain rated power over a wide range of battery voltage. Excellent frequency response rates place these amps in a class of their own.

SOUND SPECIALIZATION: This high-powered Power Amplifier is cutting edge technology at its finest. Chrome RCA connectors and speaker screw-down terminals ensure a secure connection between amplifier and speakers that allow distortion-free sound.

INTELLIGENT DESIGN: The car audio amplifier 5 channel safety features include power and protection LED indicators; soft turn-on/off; and thermal, overload, and speaker-short protection.

Power - 300 Watts Max x 4 @2-Ohms 150 Watts Max x 4 @4-Ohms 600 Watts Max Bridged x 2 @4-Ohm

Class D - Power loss is significantly reduced making the amplifier highly efficient Excess energy is stored until it’s needed instead of being converted into heat Reduction in size/weight reduced power waste smaller heat sink compact circuitry

Bridgeable - Dramatically increase the power output to you speakers and subwoofers by connecting two amplifier channels

1600 WATT POWER: The Pyle 4 Channel Car Amplifier is perfect for your vehicle's sound system. Gives you up to 1600W bridgeable output. Features switchable bass boost, variable gain control, configurable electronic crossover network

SILVER-PLATED RCA PORTS: The RCA ports are silver-plated for eliminating signal loss. The subsonic filter allows low-end interference to be cut so your speakers will always deliver the highest quality audio

DISTORTION-FREE: The MOSFET pulse width modulation power supply allows for a clean distortion-free signal to your compact speakers providing you w/ crisp and clear audio for an outstanding music experience. Also features pulse width modulation system

110 W/Ch. (6 Ohms, 1 kHz, 0.9% THD, 1 Channel Driven, FTC); 65 W/Ch. (8 Ohms, 20 Hz-20 kHz, 0.7% THD, 2 Channels Driven, FTC)

HDMI 2.0a Support for 4K/60 Hz, 3D,Audio Return Channel, DeepColor, x.v.Color, Lip-sync, Dolby True HD, DTS-HD Master Audio, DVD-Audio, Super Audio CD, Multichannel PCM, and CEC

Built-in Bluetooth to stream virtually any audio from your smartphone, tablet, or PC to your home theater for clear and powerful sound

400 W MAX Power @ 2 Ohm x 4 Channels

200 W MAX Power @ 4 Ohm x 4 Channels

800 W MAX Bridged Power @ 4 Ohm x 2 Channels

1000-WATT POWER: The Crunch PowerDriveX Car Stero Amplifier boasts 1000 Watts power; 2 x 250 watts at 4 ohms, 2 x 500 watts at 2 ohms, 1 x 1000 watts at 4 ohms bridged

2 CHANNEL AMP: 2 Channel amplifier with Low noise pre amplifier with Rugged MOSFET pulse width modulation power supply; Series A/B car amplifier; Maximum low voltage signal from the source unit comes into the amplifier circuit with minimal distortion

INPUTS/OUTPUTS: Low level RCA inputs and outputs; Audio inputs: Unbalanced inputs (RCA) Audio outputs: Line output (RCA)

Competition Grade Class D Monoblock Amplifier

Peak Power at 1 Ohm: 9,000 Watts | RMS Power at: 3,000 Watts.

Stable at 1 Ohm, Frequency Response: 15 Hz to 250 Hz

RMS Power Rating: 4 ohms: 60 watts x 4 chan. / 2 ohms: 90 watts x 4 chan. / Bridged: 4 ohms: 180 watts x 2 chan.

Max power output: 800 watts

3-way protection circuitry (thermal, overload, and speaker short protection)

DS18 GEN-X3700.4D has the following RMS power: at 2 Ohms 225 watts / at 4 Ohms 150 watts / Bridge Powered at 4 Ohm 375 watts - THD Distortion 0.08%

Designed, Engineered, Developed, and Quality Controlled in the USA - Minimum THD at Rated Power: 98dB. Under Voltage Protection at 10V. Over Voltage Protection at 15V. Frequency Response: 20Hz - 20KHz. Fuse Rating 40A x 3

High-Speed MOSFET Power Supply Optical Coupler Class "A/B"Technology. Fully Adjustable 12dB. Low Pass Filter: 50Hz - 500Hz. High Pass Filter: 50Hz - 500Hz. Phase Control Switch. Full IC-Controlled Protection Circuitry. Remote Dashboard Subwoofer Control.

RMS Power Rating: 4 ohms: 115 watts x 2 chan./2 ohms: 175 watts x 2 chan./Bridged, 4 ohms: 350 watts x 1 chan.

Pulse Width Modulated MOSFET power supply

LED power (green) and protect (red) indicators

Configurable as 6/5/4/3/2 channel amplifier

6 x 200 watts @ 2 ohms - 6 x 125 watts @ 4 ohms

400 watts @ 4 ohms bridged - AccuBASS Processing

This listing contains: (1) V1200.5 2400 Watt 5 Channel Class A/B Amplifier (1) Remote Bass Knob with Connector cable

4 x 75W + 1 x 300W @ 4 Ohms 4 x 150W + 1 x 600W @ 2 Ohms 2 x 300W + 1 x 300W @ 4 Ohm N/A + 1 x 600 @ 2 Ohm

Features: Nickel Plated Terminals Low Level Inputs Remote Bass Knob Included Mil Spec Double-Sided Glass Epoxy FR Circuit Board 4-Way Protection Circuitry: Thermal, Short Circuit, Overload and DC Offset Variable Low-Pass Crossover: 50Hz - 250Hz Variable Input Sensitivity: 200mV - 6V Phase Control: 0 - 180 Degree 45Hz Bass Boost: 0 - 12dB S/N Ratio: > 85dB THD: 0.08%

3 stereo power levels 300W 450W or 600W per channel @ 4 ohms

2 Module input bays for flexible modular input capability

3 mono power levels 600W 900W or 1200W for 70V speaker systems

245 Watts RMS x 1 @ 4 ohms

425 Watts RMS x 1 @ 2 ohms

750 Watts RMS x 1 @ 1 ohms

2 Pieces Bundle of Taramps products

The Smart 3 is a multi-impedance amplifier operate between 1 to 2 ohms

The Smart 3 has power control system technology ensures greater performance and safety. It is a mono, 3000 Watts RMS amplifier, which has protection against short circuit at the output, high/low voltage and thermal protection

Package Includes: (1) Power Acoustik RE4-2000D 2000 Watt 4-Channel Car Stereo Amplifier Amp. (1) RockvilIe RWK42 4 Gauge 4 Channel Complete Wire Kit With (2) RCA Cables. Features of RE4-2000D: Power Acoustik RE4-2000D 2000 Watt 4-Channel Car Amplifier

4 Channel Full Range Operation 2-Ohm Stable Class A/B Amplifier. MAX Power: 2000 Watts. 4 Ohm RMS: 175 Watts x 4. 2 Ohm RMS: 250 Watts x 4. 4 Ohm RMS Bridged: 500W x 2. Direct Short, Thermal, & Overload Circuits Protection. 200mV-6V High Level or Low Level RCA Input. Tri-Mode Capable

Variable 12dB High, Low, & Subsonic Crossovers. Variable 12dB Band-Pass Crossovers. Direct Wire 4ga. Power & 12ga Speaker Terminals. Product Dimensions (L x W x H): 13" x 8.5" x 2.2" inches. Features: RockvilIeRWK42 4 Gauge 4 Channel Car Amplifier Wiring Installation Kit

“Auto Power On” with high-level input compatible with OEM stereo

Compact Aluminum chassis with high thermal dissipation

Can be used in 3 4 5 & 6 channel modes

SOLID 1 - Focal Monoblock 470 W RMS Power Amplifier + SOLID 2 Black - Focal 2-Channel 200W RMS Power Amplifier

Solid-1: Power RMS (4 Ohms)1 x 300W | (2 Ohms)1 x 470W | (2 Ohms) 1 x 940W Max

Solid-2 Power: 75 watts RMS x 2 at 4 ohms (100 watts RMS x 2 at 2 ohms) | 200 watts RMS x 1 bridged output at 4 ohms (4-ohm stable in bridged mode)

RMS Power @ 4 ohm Stereo 100 x 4 watts RMS @ < 1.0% THD

RMS Power @ 2 ohm Stereo 150 x 4 watts RMS @ < 1.0% THD

RMS Power @ 4 ohm Mono 300 x 2 watts RMS @ < 1.0% THD

Improving on the compact amazingness that was the IA6.4, we bring you the all new IX6.4 that takes it to the next level in every sense. In a space of just 11” long, we were able to wring out 150 watts a channel at 4 ohms, and a whopping 500 watts by 2 channels at 4 ohms. That means, you could power a pair of subwoofers with ease, using the IX6.4 if you wanted to. Don’t forget, the IX6.4 comes with a bass remote for just this purpose.

Not wanting a complex set up to deal with? You could use the IX6.4 as a full system solution with components on the front channels, while powering a strong subwoofer bridged on the rear 2 channels.

Our amps have always been loaded with features. For example, the IX6.4 comes with a mirror feature where you can match everything you set on channels 1&2, mirrored over to channels 3&4. Another great feature is the separate clipping indicators, one for channels 1&2, and another for channels 3&4. A feature on our IX6.4 that is standard to our multi-channel amplifiers is the fully active capable, crossover network.