Best Rockford Fosgate Multichannel Amplifiers in 2026

Bass Restoration Processor, Included ACR-1 Remote Level Control & 20' RJ-14 Cable

Enhanced bass output: The device restores low-end frequencies and provides a more dynamic and immersive listening experience.

Built-in bass maximization circuit: The circuit allows you to adjust the frequency response and control the level of the bass output.

Class D MOSFET Monoblock Power Amplifier

Peak Power at 1 Ohm: 1,600 Watts | RMS Power at 1 Ohm: 1,200 Watts

Frequency Response: 20Hz - 250Hz, On-board Bass EQ Switch with +6 or +12dB boost at 45Hz

High-Resolution Audio is high-quality sound that exceeds CD standard. High-resolution audio captures and beautifully expresses all the details of your favorite music. Through ultra-high and low frequencies, immerse yourself in a rich and high-quality sonic experience.

Output Coil with Magnetic Shield prevents magnetic flux from radiating from the subwoofer's coil, resulting in reduced noise and enhanced sound quality.

Detachable sliding terminal cover offers a sleek design and easier installation.

160 watts RMS x 2

variable low- and high-pass filters

selectable bass boost

Input Sensitivity: 125mV–5V (Low Level) / 1V–40V (High Level)

Signal-to-Noise Ratio: 95dB

Frequency Response (Hz): 10Hz-20kHz

The Punch P1000X5 is an ultra-efficient 5-channel amplifier (2.38” x 7.76” x 15.03”) capable of running your entire system without excessive drain on your charging system and rocking 1000 watts of RMS power

Perfect for running a front/rear system and a dedicated subwoofer (RMS Power Output: 75 Watts x 4 + 150 Watts x 1 @ 4-Ohm OR 125 Watts x 4 + 300 Watts x 1 @ 2-Ohm OR N/A + 500 Watts @ 1-Ohm)

RCA inputs can accept both Hi and Low level audio signals without the need of a signal converter and tri-stage protection that covers thermal, over-current and short circuits

Includes: Amplifier. Birth sheet with tested power. Owner’s manual. Mounting Screws. Warranty.

Features: Rockville dB45 3200 Watt/800 Watt Dyno-Certified RMS 4 Channel Amplifier Car Stereo Amp, Loud!!.

Dyno Certified RMS Power Ratings: (Certified Dyno Test / Less than 1 % THD) (Use these ratings when comparing with top brands such as Kicker, Rockford Fosgate, etc). - 2 Ohm: 200 Watts x 4 Channel <1% THD+N . - 4 Ohm:135 Watts x 4 Channel <1% THD+N. - 4 Ohm Bridged: 400Watts x 2 Channel<1% THD+N.

550 W MAX Power @ 2 Ohm x 4 Channels

275 W MAX Power @ 4 Ohm x 4 Channels

1100 W MAX Bridged Power @ 4 Ohm x 2 Channels

Belva Complete 4 Gauge Amp Kit with 4 ch. RCA

Excellent for voice as well as bass

2 ohms

400 watts

New Kenwood 4 channel Bluetooth marine atv motorcycle amplifier (kacm1824bt)

45 watts x 4 at 4 ohms

Peak power: 400 watts

Stereo/parallel/bridge-mono mode

User selectable input sensitivity - 0. 775V and 1. 4V

Electronically balanced RCA & XLR inputs; binding post and Speak on outputs

750 watt maximum power full-range amplifier

Amplifier Class: AB

No. of channel: 2/1 Channel

Two Amplified Output Ports (Gain: 11.5 dB)

Works with all TV Antennas & CATV Installations (Not Compatible with Satellite)

Improves Signal Strength, Decreases Pixelation and May Increase Number of Channels

1500W Maximum Power Full-Range Amplifier

Optimized 150-watt RMS output and a max power output of 1500 watts, you can give your music a huge boost in power that will have you and your passengers partying while on the road

This slim amplifier fits perfectly into any trunk so you can easily connect it to your stereo system

1400 WATT POWER: The Pyle Dual Channel Car Amplifier is perfect for your vehicle's sound system. Gives you up to 1400W bridgeable output. Features switchable bass boost, variable gain control, configurable electronic crossover network

GOLD-PLATED RCA PORTS: The RCA ports are gold-plated for eliminating signal loss. A subsonic filter allows low-end interference to be cut so your speakers will always deliver the highest quality audio. Features switchable bass boost, low level inputs

MOSFET PULSE: The MOSFET pulse width modulation power supply allows for a clean, distortion-free signal to your compact speakers providing you with crisp and clear audio for an outstanding music experience. Also features anti-thump turn on

Bridgeable

Variable input voltage

QTD (Quick Thermal Dispersion) technology heat sink

PEAK POWER: Max Power 600 Watts. RMS (50 Watts x 4 @ 4-Ohm or 75W x 4 @ 2-Ohm

RMS POWER: (50 Watts x 4 @ 4-Ohm or 75W x 4 @ 2-Ohm. High Quality KENWOOD sound you can depend on

MARINE CERTIFIED: Conformal coated marine grade circuit board is great for any application including Car, Boat, ATV, UTV etc.

1 x Taramps TS400X4 Full Range Amplifier

Quantity: 1 Amplifier Number of Channels: 04 Max Power at 13.8 VDC 2 Ohms: 400W (4 x 100W RMS) Max Power at: 13.8 VDC 4 Ohms: 252W (4 x 63W RMS) Bridged at 13.8 VDC 4 Ohms: 400W (2 x 200W RMS)

Input Sensitivity: 200mV (Vol=Max) Signal to Noise Ratio: greater than 90dB Frequency Response: (Full Range): 18Hz to 30kHz (-3dB) High Pass Crossover (HPF): 90Hz (-12dB / 8th) Low Pass Crossover (LPF): 90Hz (-12dB / 8th)

100 WATT MAX: The Pyle Multi-Zone A B Speaker Selector Switch is perfect for your home theater sound system w/ 100W max power per channel. For use w/ 8ohm impedance speakers. Has a compact slim tabletop design that complements any home theater setup

CONTROL 4 SPEAKERS: The new indoor multichannel speaker switcher controls up to 4 speaker pairs connected to a stereo amplifier at the same time or in combination. Input/output via screw type connector terminals which accept up to 14AWG speaker wire

INDEPENDENT AUDIO CONTROL: Features independent audio source channel volume controls. The push button design lets you activate each pair individually to customize the listening experience in your home and independently control the volume to each pair

Power - 600 Max x 4 @ 2 Ohms, 300 Max x 4 @ 4 Ohms, 1200 Max Bridged x 2 @ 4 Ohms

Variable Bass Boost - With Variable Bass Boost you have the control of exactly how much BASS you want to pump out to your subwoofer(s)

Variable Low-Pass Crossover - Subwoofers reproduce sound based on a number of different low-range frequencies. You can set exact sound specifications for the bass frequency reproduction

Class A/B MOSFET 4 Channel Amplifier

Peak Power: 4x300 @ 2 Ohms, 4x150 @ 4 Ohms, 2x600 Mono Bridged @ 4 Ohms

Frequency Response: 10Hz - 45KHz, Built in bass control with 0-12dB boost

The DS 800X4 is a multi-channel amplifier and can be used to sub-bass, bass, mid-bass, mid-range, high-mid and treble.

The Positive/Negative power supply cable is 7 AWG. The output cables wire gauge is 15 AWG and the remote cable is 18 AWG. For Protection fuse or circuit breaker please use 60A.

Short-circuit Protection: Shutdown the amplifier when detect a short- circuit or impedance lower than the supported at the output

1000 watts Max power

Automatic signal Sensing and turn-on

Variable high Pass filter adjustable bass Boost

This part requires programming and/or special setup procedures. GM Service Information describes the procedures and special tools needed to ensure proper operation in the vehicle

Helps provide a wonderfully rich listening experience in your vehicle

Some GM Genuine Parts may have formerly appeared as ACDelco GM Original Equipment (OE)

1, 200 Watts Max Power

Compact Design for Versatile Installation Options

Refined Class FD Design Offers Extreme Efficiency and High-Quality Sound

New Kicker 43CXA3004 300W 4-Channel Car Audio Power Amplifier Amp Stereo CX300.4

75W x 4 @ 14.4V

150W x 2 @ 14.4V, 4-Ohm bridged mono

Quality - This Class D 4 channel amplifier exhibits quality frequency response rates and crossover network which places this amp at a prominent place. Durable design and highly efficient performance makes this subwoofer amp for car speakers stand out amongst the others.

Power – This Class D 1200 Watt RMS Car Amplifier has a power rating distribution as followed 300x4 @2 Ohms, 192x4 @4 Ohms. The 4 channel amplifier for car speakers also provides a 2-way protection circuitry as a part of its design.

Crossovers- The Taramps Multichannel Car Amplifier offers you the ease of connectivity by providing the feature of crossover. The 2 channel car amplifier provides you with options of fixed 90Hz Highpass & Lowpass crossovers.

RMS Watts @ 4 Ohm Stereo 12.6V:   1050 Watts X 1 Channel / RMS Watts @ 2 Ohm Stereo 12.6V: 1600 Watts X 1 Channel / RMS Watts @ 1 Ohm Stereo 12.6V: 2500 Watts X 1 Channel

Nominal power output 1ohm(watts): 5000 Watts, Max music power: 10000 Watts

Frequency Response   20Hz~250KHz

HUGE POWER IN A SMALL PACKAGE - 1,600 Watts gives you all the power you need tucked away and out of sight, keeping your vehicle looking clean and neat.

WIDE RANGE OF APPLICATIONS - Ranging from 2-8 ohms, this amplifier will allow you to use a variety of speakers for your specific application. Never again will you need to worry about having the right amp for the job.

EXTREMELY POWER EFFICIENT AMPLIFIER - Push an amazing amount of power to your system while only drawing minimal power from your vechicle's battery.