Best Oxygen Sensor Removers in 2026

【Design】 Standard 6 point with low profile and slotted design to enable you remove oxygen sensors with the wiring harness still attached, and the socket is offset and compact which allows extra leverage even in hard to reach spots.

【USE】 Built for use with ratchets and breakers bars to remove and install oxygen sensors and hex vacuum switches on vehicle, even if you don't have a lot of experience working with cars. This high quality tool can save your time!

【Package】1-pc 3/8” Dr. extra deep broach socket (3-1/8” long), 1-pc 3/8” Dr. low-profile crowfoot socket wrench (1-1/4” long), 1-pc 1/2” Dr. offset crowfoot socket wrench (1-15/16” long), 1-pc M18 x 1.5mm and 1-pc M12 x 1.25mm thread chasers with 3/8” drive to clean and repair damaged threads

Perfect tool set for removing, inspecting, replacing and installing heated and non heated oxygen sensors and vacuum switches on most vehicles with computer-controlled engines

3 types of universal socket wrenchs cover various situations of oxygen sensor location

6-point 7/8” (22mm) socket opening fits all hexagon oxygen sensor, common 3/8” and 1/2” drive ends can be used with ratchet or breaker bar

【High Qulity】Made of high performance chrome molybdenum and solid cast steel construction for strength and durability - Finished with Black Oxide to prevent rust and corrosion.

【Size】 7mm slot, 7/8” (22mm) x 6-point x 3-1/10” (80mm) length, 3/8 inch square drive for use with ratchet. Fits all standard oxygen sensors with a 7/8” hexagon nut.

【Design】Standard 6 point with low profile and 8mm x 64mm side cutout design to enable you remove oxygen sensors with the wiring harness still attached, and the socket is offset and compact which allows extra leverage even in hard to reach spots.

Usage: This tool sets are used to remove. Inspect, replace and install oxygen sensors and vacuum switches on vehicles and engines.

Package: There are 5pcs sockets and wrenches included in the red case, 1-pc 3/8” Dr. extra deep broach socket (3-1/8” long), 1-pc 3/8” Dr. low-profile crowfoot socket wrench (1-1/4” long), 1-pc 1/2” Dr. offset crowfoot socket wrench (1-15/16” long), 1-pc M18 x 1.5mm and 1-pc M12 x 1.25mm thread chasers with 3/8” drive to clean and repair damaged threads

Material: These sockets and wrenches are forged with high quality steel and gain a high strength which give them a better performance.

INCLUDES: This set includes a 29mm 1/2-inch drive Vacuum Switch Socket, 27mm 1/2-inch drive Injector Socket, 27mm 3/8-inch drive Oil Sender Unit 1-inch Socket, 22mm 3/8-inch drive Vacuum Switch Socket, 22mm 1/2-inch drive Heated O2 Sensor Socket, 27mm 3/8-inch drive Oil Sender Unit 1-1/16-inch Socket, 22mm 3/8-inch drive 6-Pt Offset O2 Sensor Wrench, M12 x 1.25mm and M18 x 1.5mm O2 Sensor Rethread Tools, and a 22mm 1/2-inch Drive Deep Offset O2 Sensor Socket."

QUALITY: All tools in this 10-piece Oxygen Sensor Socket Set are constructed of high strength Chrome Vanadium Steel with a Manganese Phosphate coating to resist corrosion."

STORAGE: This Oxygen Sensor Socket set comes complete with convenient storage case so you'll never misplace a socket on the job again!

Ideal for removing and installing oxygen sensors and vacuum switches on vehicles with computer-controlled engines

3 Different types of sockets cover various situations of oxygen sensor locations

Universal 6-point 7/8” (22mm) socket opening fits all hexagon oxygen sensor, common 3/8” and 1/2” drive ends can be used with ratchet or breaker bar

Application: This socket set is designed for the removal inspection or replacement of heated and non-heated oxygen sensors fitted to the following vehicle Audi, BMW, Citroen, Mercedes, Peugeot, Renault, Skoda. These sockets feature cut-away sections allow some sockets to fit over wiring harnesses, complete with the black phosphate finish for a durable design.

3/8’’ Drive × 7/8’’ ×1/2’’ Oxygen Sensor Socket/Vacuum Switch Socket removes and installs vacuum switch with a 7/8’’ hex and some oxygen sensors; 3/8’’ Drive × 7/8’’ × 3-1/8‘’ oxygen sensor socket removes and installs oxygen sensors in domestic and many import vehicles. Slot in socket for wire clearance.

1/2’’ Drive ×1-3/16’’ ×3-1/2’’ vacuum switch socket removes oil pressure sending units on late 80’s to mid 90’s GM models; 1/2’’ Drive ×1-1/16’’ × 3-1/4’’ thermal sensor switch socket removes and installs thermal sensor switch on 1973-1977 CM vehicles; 3/8’’ Drive ×1’’ and 1-1/16’’ ×3’’ remove oil pressure sending units. Deep design fits switches up to 2-5/8’’.

Used for removing and installing oxygen sensors in many vehicles that are 7/8inches / 22mm in size

2pcs CR-MO Steel 6 Point Sockets

1pcs CR-V Steel 6 Point Socket

Oxygen Sensor Socket Wrench Including: 1-pc 3/8” Dr. extra deep broach socket (3-1/8” long), 1-pc 3/8” Dr. low-profile crowfoot socket wrench (1-1/4” long), 1-pc 1/2” Dr. offset crowfoot socket wrench (1-15/16” long), 1-pc M18 x 1.5mm and 1-pc M12 x 1.25mm thread chasers with 3/8” drive to clean and repair damaged threads

Oxygen Sensor Socket Wrench Set Special side cutout design allows easy access to oxygen sensors from any section and prevents damage to wires，Perfect tool set for removing, inspecting, replacing and installing heated and non heated oxygen sensors and vacuum switches on most vehicles with computer-controlled engines.

5 Pcs Oxygen Sensor Switch Socket Wrench Kit and Thread Chaser Set-3 types of universal socket wrenchs cover various situations of oxygen sensor location,6-point 7/8” (22mm) socket opening fits all hexagon oxygen sensor, common 3/8” and 1/2” drive ends can be used with ratchet or breaker bar.

[SIZE]: 3 piece 3/8 & 1/2" drive O2 oxygen sensor wrench socket tool set; universal 7/8"/22mm professional grade removal tool for cars & automotive

[ITEM INCLUDES]: 1 vacuum switch socket & 2 puller sockets kit

[MATERIAL]: Constructed of high performance (cr-v & cr-mo) vanadium and chrome molybdenum solid cast steel for strength and durability - finished with black oxide to prevent rust

【Package】Includes 2 7/8" 3/8 Inch Drive Vacuum Switch Sockets and One 7/8" x 1/2" drive Oxygen Sensor Socket

【Design】 Standard 6 point with low profile and slotted design to enable you remove oxygen sensors with the wiring harness still attached, and the socket is offset and compact which allows extra leverage even in hard to reach spots.

【Material】 Made from high performance chrome molybdenum and solid cast steel construction for strength and durability - Finished with Black Oxide to prevent rust.

Function: The Apeixoto oxygen sensor removers will help your in adjusting and removing oxygen sensors, oil pressure sending unit vacuum swithces and fuel injections. These tools can be used most vehicles.

Packages: There are 10 pieces removers and sockets in the red case. The whole tool set comes in a solid red case which will protect the tools well during shpping and let you keep the tools well after usage.

Specifications: The specification for these 10 oxygen sensor sockets are : 1/2 inch dr x 22mm x 6PT x 110mm, 1/2 inch dr x 29mm x 6PT x 90mm, 1/2 inch dr x 22mm x 12PT x 78mm, 1/2 inch dr x 27mm x 12PT x 78mm, 1/2 inch dr x 28mm x 12PT x 78mm, 1/2 inch dr x 7/8 inch x 50mm, 3/8 inch dr x 7/8 inch x 6PT x 80mm, 3/8 inch dr x 7/8 inch x 6PT x 90mm, 3/8 inch dr x 7/8 inch x 30mm, and 3/8 inch dr x 1 inch and 1-1/6 inch x 74mm

REMOVE OXYGEN SENSORS FROM YOUR VEHICLE: This 10 Piece Specialty Sockets O2 Sensor Tool Set lets you quickly and easily remove oxygen sensors, oil pressure sending unit, fuel injectors, and vacuum switches; Some O2 socket pieces feature cutout sides to prevent damage to wires and tubes; Remove and install parts on most domestic and some international vehicles

USE WITH YOUR TOOLS: Features 3/8-inch or 1/2-inch square drive to fit your O2 sensor wrench drives; For use with ratchet, breaker bar, or hand wrench (driver tools not included); Not compatible with impact tools; Use this tool in conjunction with the O2 Sensor Thread Chasers to install new sensors easily (thread chaser and sensors not included)

BUILT TO LAST: Constructed of heat-treated chrome vanadium steel, this oxygen sensor remover set is built for strength, durability, and longevity; Each 02 sensor socket is coated with a black oxide finish to provide resistance to rust and corrosion

Used for removing and installing oxygen sensors in many vehicles that are 7/8" / 22mm in size

1 3/8” Drive 7/8”x80mm (L) Vacuum Switch Socket - 2 3/8” & 1/2" drive, 30 & 50mm (L), ‘Crows Foot’ type Oxygen Sensor Sockets - Comes in a molded case

Constructed of high performance (CR-V & CR-MO) vanadium and chrome molybdenum solid cast steel for strength and durability - Finished with Black Oxide to prevent rust

Premium Quality: This automotive oxygen sensor socket set is made of premium material with delicate workmanship, heat treated chrome vanadium & chrome molybdenum steel with black oxide finish for corrosion resistance. They are sturdy in structure and will not easily crack under high pressure to achieve maximum strength and service life.

Excellent Design: The pressure vacuum switch socket kit adopts a 6-point high torque design, which touches and grasps the firmer flat side of the nut or bolt head, rather than the weaker corner. Slotted design allows removing oxygen sensor with wiring harness attached and prevents damage to wires. Each socket is permanently etched with size marking for your convenience.

Diversified functions: This oil pressure sending unit master socket is ideal for the removal and installation of oxygen sensors, oil pressure sending units, oil pressure switches, vacuum switches equipped with wires or vacuum tubes and thermal sensor switches. Humanized design, indenter design, non-slip, wear-resistant, and careful makes it ideal for home, construction and auto shops.

Suitable for oxygen sensors found on most modern vehicles

Cut-out and slots enable sockets to be fitted over wiring harness

Includes 2 chasers for cleaning and repairing damaged threads

Ideal for removing and installing oxygen sensors and vacuum switches on vehicles with computer-controlled engines

3 Different types of sockets cover various situations of oxygen sensor locations

Universal 6-point 7/8” (22mm) socket opening fits all hexagon oxygen sensor, common 3/8” and 1/2” drive ends can be used with ratchet or breaker bar

Perfect tool for removing, inspecting, replacing and installing heated and non-heated oxygen sensors on most vehicles with computer-controlled engines

The 6-point 7/8” (22mm) socket opening fits all hexagon oxygen sensor, common 1/2” drive and 7/8” ends can be used with both ratchet and torque wrench

The oxygen sensor socket's special side cutout design allows easy access to oxygen sensors from any section and prevents damage to wires

7 pc sensor and sending unit socket set

Chrome vanadium steel construction

Oil rubbed Black oxide coating for corrosion resistance

* For use the most all oxygen sensors no matter what size electrical connectors they have

* Double-sided design, 12-point configuration on one side and 6-point on the opposite side

* 12-point side enables twice the number of "clock angle" attachment positions allowing oxygen sensor removal in difficult areas

7-PIECE SOCKET SET: This Orion Motor Tech set comprises a 22mm vacuum switch socket with 3/8" drive, 29mm thermal switch socket with 1/2" drive, 22mm O2 sensor socket with 3/8" drive, 27 mm injector socket with 1/2" drive, 27mm oil sender unit socket with 3/8" drive, 22mm offset O2 sensor wrench with 3/8" drive, and 22mm offset O2 sensor wrench with 1/2" drive

HEAVY-DUTY TOOLS: Each of the 5 sockets is made of heat-treated chrome vanadium steel with electroplated chrome coating, while the 2 offset sensor wrenches boast chrome molybdenum steel with black oxide finish, with all parts ensuring superior wear & corrosion resistance and long-term durability under even punishing use

WIDE APPLICATION: Perfect for removal and installation of oxygen sensors, oil pressure sending units, diesel injectors, vacuum switches, and thermal sensor switches, this heavy-duty sensor socket removal kit is compatible with Audi, BMW, Citroen, Mercedes, Peugeot, Renault, Skoda, Vauxhall/Opel, and Volkswagen models

[Remove Oxygen Sensors]: When adjusting an oxygen sensor in a tight spot, use the ABN Oxygen Sensor Wrench Tool; O2 sensor wrench package includes (1) O2 sensor socket wrench with 6pt socket and 12pt socket on 1 head - downstream recommended

[Access Difficult Spots]: Reaching O2 sensors can be difficult; Slim design with flex head of oxygen sensor socket wrench tool offers extra clearance for removal and installation of oxygen sensors positioned upward and inward of floorboard

[Offset Grip]: Oxygen sensor socket tool O2 socket wrench 8-inch (20cm) handle curves at 4 inches (10cm) for leverage and clearance around exhaust pipes; Flip O2 sensor tool removal handle to let curved handle fit most spaces

Wide Applications: Used for removing and installing oxygen sensors in many vehicles that are 7/8" / 22mm in size and hex vacuum switches on vehicles with computer-controlled engines

Durable & Dependable: Oxygen Sensor Set is made of chrome molybdenum construction and black oxide finish for easy cleanup & rust prevention;

Professional Grade: 3/8 & 1/2-inch Drive O2 Oxygen Sensor Wrench Socket Tool. Professional Grade Removal Tool for Cars & Automotive

Perfect tool for removing, inspecting, replacing and installing heated and non-heated oxygen sensors on most vehicles with computer-controlled engines

The 6-point 7/8” (22mm) socket opening fits all hexagon oxygen sensor, common 3/8” drive and 7/8” ends can be used with both ratchet and torque wrench

The oxygen sensor socket's special side cutout design allows easy access to oxygen sensors from any section and prevents damage to wires

【WHAT YOU GET】 1PC 1/2'' Drive x 27mm oil pressure sending unit socket. 1PC 1/2'' Drive x 29mm pressure/vacuum switch socket with slot. 1PC 1/2'' Drive x 7/8'' long sensor wrench socket with slot. 1PC 3/8'' Drive x 7/8'' vacuum switch socket with slot. 1PC 3/8'' Drive x7/8'' (6 point) vacuum switch socket with slot. 1PC 3/8'' Drive x 1-1/16'' & 1'' (6 point) oil pressure sending unit socket. 1PC 3/8'' DR x 7/8'' (6 point) short sensor wrench socket with slot.

【FUNCTION】 Designed for the removal and installation of sensors, oil pressure sending units and vacuum switches equipped with wires or vacuum tubes on most vehicles. Provide additional leverage even in hard-to-reach places. We offers premium after-sales service and technical support to each customer.

【FEATURES】 Constructed of high performance chrome vanadium for strength and durability. Finished with Black Oxide to avoid rust. Side cutout design allows easy access to from section and avoids from damage to wire.

Durable Material: The O2 sensor socket kit is constructed of vanadium and molybdenum steel for strength and durability.Black oxide finish to prevent rust and add longevity.

Specification: The specification for these oxygen sensor sockets are: 1pc 3/8 inch Drive 7/8 inch (22 mm) Deep, 1pc 3/8 inch Drive 7/8 inch (22 mm) Crowfoot, and 1pc 1/2 inch Drive 7/8 inch (22 mm) Deep Crowfoot Sockets, 1pc plastic carrying case

Unique Design: This Oxygen sensor socket set features standard 6 point with low profile and slotted design to enable you remove oxygen sensors with the wiring harness still attached, and the socket is offset and compact which allows extra leverage even in hard to reach spots

Extra Durable: Constructed of heat-treated chrome vanadium steel, this oxygen sensor remover tool set is built for strength, durability, and longevity.

Function: O2 sensor socket tool set lets you quickly and easily remove oxygen sensors, oil pressure sending unit, fuel injectors, and vacuum switches.

Features: 3/8-inch or 1/2-inch square drive to fit your O2 sensor wrench drives, the o2 sensor socket set is designed for use with ratchet, breaker bar, or hand wrench (driver tools not included), Not compatible with impact tools.

3 types of universal socket wrenchs cover various situations of oxygen sensor location

Including: 1-pc 3/8” Dr. extra deep broach socket (3-1/8” long), 1-pc 3/8” Dr. low-profile crowfoot socket wrench (1-1/4” long), 1-pc 1/2” Dr. offset crowfoot socket wrench (1-15/16” long), 1-pc M18 x 1.5mm and 1-pc M12 x 1.25mm thread chasers with 3/8” drive to clean and repair damaged threads

M12×1.25MM & M18×1.5MM Threads Chaser: Oxygen sensor thread chaser tool are used for cleaning and re-threading damaged spark plug hole. Cleans damaged spark plug ports and threads. Rethreads damaged spark plugs, eliminates corrosion and straights damaged threads. Reduces the chance of cross threading.

Flexible head design that assists in the removal of stubborn O2 sensors that are 7/8 inch in diameter

Features allow extensions or wrenches to apply force in tight areas even on seized components

Pivots to allow more angles of placement

🔧[Oxygen sensor socket wrench remover tool set]: 3pcs oxygen sensor socket wrench removers and 2pcs thread chaser tools, it is meet for most oxygen sensors’ installation and removal requirements

🔧[Oxygen sensor socket size]: Oxygen sensor socket 1/2" drive x 7/8" 22mm x 50mm, o2 sensor socket 3/8" drive x 7/8" 22mm x 30mm, 02 sensor socket 3/8" drive x 7/8" 22mm x 80mm; Thread chasers: M12 x 1.25mm / M18 x 1.5mm

🔧[High-quality materials]: Made of high-strength chrome vanadium steel. Please rest assured of our products,they are sturdy enough to install and remove the oxygen sensor. The outer layer prevents oxidation and rust through phosphating and electroplating to increase of service life