Best Space Heater Replacement Parts in 2026

【GLASS TUBE FOR PATIO HEATER】This Quartz glass tube is a perfect replacement part for a four-sided Pyramid Flame Heater. You can fit this 49.5" long tube into any standard Pyramid Heater to get it back to full working order. This patio heater replacement glass tube doesn't fit with three-sided heaters.

【EASY INSTALLATION】Our Pyramid patio heater parts are easy to install, with a special black rubber connecting ring included for attachments, so getting your outdoor space back up and running should be no trouble. Once installed this propane heater glass tube replacement should last a long time. It only takes one minute for a person to replace , refer to the video.

【 HIGH TEMPERATURE RESISTANCE】This heater glass tube replacement piece is made from strong and heat-resistant Quartz glass. This makes the glass hard to damage and helps it maintain a good condition during combustion, even in poor weather conditions. Outdoor heater replacement parts have to be able to handle heat!

FREE Tech Support. Use amazon messager to contact Seller.

Quadrafire Pellet Stove Control Box SRV7000-205

Replaced 812-3390, 812-4410, 812-4940 and 812-3392

⭐PP204 / HA3004 1/2" Rotor Kit,Includes Rotor, Vanes, and Insert Rotor Kit 1/2" Thick Dia= 2 1/8".

⭐This kit (includes the vanes and insert) is used on a variety of different heater models. The other part numbers are: Desa part# PP204, GHP part#SP-KFA1000, Mi-T-M part# 68-3043, Pinnacle part# 70-022-0100

⭐Other Part Numbers: PP204 , HA3004 , M22456-1 , 70-022-0100 , 700220100 , 71-022-1300 , 710221300 , SP-KFA1000 , SPKFA1000 , KFA1000 , 68-3043,and For more model

PREMIUM QUALITY REPLACEMENT PARTS - Manufactured with high-quality materials that exceed OEM standards. The dump switch is made of heavy-duty ABS plastic while the thermocouple components are made of high-standard red copper and brass. Easy to install and use, this replacement kit will allow you to enjoy your space without worrying about your safety.

GUARANTEED PROPER FIT - Our replacement parts are highly compatible with different models of propane gas heaters including propane patio heaters, indoor room gas heaters, and thermoelectric gas heaters.

UNIVERSAL M8*1 THREAD THERMOCOUPLE - The patio heater thermocouple wire has a full extension length of 350mm with temperature resistance sleeves. It has an M8*1 fixed thread head with end thread nuts that are compatible with 8mm gas valves.

REPLACES PART DESA NUMBER 098514-01

Product Type:The 098514-01 Thermocouple will fit the following Comfort Glow Vent-Free wall heater model numbers with fit the following Blue-Flame Vent-Free Natural Gas Heater wall heater model numbers:

Material: Copper; Power: Natural and Propane Gas

【UNIVERSAL FIT】:39" 098514-01 Thermocouple Replacement for compatible with Desa LP Glow Warm

【WORKS FOR】:The 098514-01 Thermocouple for compatible with Blue-Flame Vent-Free Natural Gas Heater wall heater model numbers: CGN18, CGN18A, CGN18B, CGN18C, CGN18T, CGN18TA, CGN18TB

【REPLACE】:for compatible with ProCom and Cedar Ridge Units: SSN18TB, SSL18TB, MD200TBE, CGD280TA, CGD280 TA Comfort Glow Vent-Free wall heater model numbers: CGCF26T, CGCF26TNA, CGCF26TP, CGCF26TPA, CGN6, CGN6L, CGN6LA, CGN10, CGN10A, CGN10L, CGN10LA, CGN10R, CGN10RL, CGN10RLA, CGN10T, CGN10TL, CGN10TLA, CGN12, CGN12A, Charm Glow, CGL250TE-C Series Heaters

GET RID OF ROTTEN EGG SMELL - Aluminum Zinc Alloy sacrificial anode rod made of high-quality Aluminum Zinc Alloy that is key element for permanently eliminate rotten egg smell from water tank.

SIZE - Flexible 44 Inch-long anode rod is hinged into four parts. Each part is less than 12 Inches allowing you to replace anode rods easily even in a narrow space. Just safely cut it shorter with a simple hacksaw.

ALUMINUM ZINC ANODE ROD KIT - The best choice to extending service life of your water heater tank from corroding is replacing water rod! This water heater anode rod makes it simple with everything you need, Anode Rod, Teflon Sealing Tape and 1-1/16” chrome finished socket, all in one box.

The magnesium anode able to give more electrochemically negative to prevent your tank dissolving itself with reasonable costs. It’s best choice for your replacement if you do have smelling water problems.

SIZE - Flexible 44 Inch-long anode rod is hinged into four parts. Each part is less than 12 Inches allowing you to replace anode rods easily even in a narrow space. Just safely cut it shorter with a simple hacksaw.

MAGNESIUM ANODE ROD KIT - The best choice to extending service life of your water heater tank from corroding is replacing water rod! This water heater anode rod makes it simple with everything you need, Anode Rod, Teflon Sealing Tape and 1-1/16” chrome finished socket, all in one box.

Fits the following heaters - 2003 models - Current MR. HEATER - MH50KT; MH75KT; MH125KT; MH175KT

Fits the following heaters - 2003 models - Current - HEATSTAR - HS50KT; HS75KT; HS125KT; HS175KT

Fits the following heaters - 2003 models - Current - ALL PRO - SPC-K50; SPC-K100; SPC-K150

★ Compatible with A.O. smith Rheem Reliance Richmond Kenmore State GE and many more water heater that use the standard 3/4" NPT Anode Rod Connection.

★ FLEXIBLE DESIGN - This 42 inch-long anode rod is hinged into four parts. Each part is less than 11 inches allowing you to replace anode rodes easily even in a narrow space. Just safely cut it shorter with a simple hacksaw.

★ CORROSION PROTECTION: Replacing anode rod at regular intervals may increase the life of water heater, saving your money, time and the inconvenience of having to replace water heater. Anode rod is expected to provide about two years of corrosion protection.

PP236 M16656-24 Photocell for Reddy Remington Master Knipco Heaters Parts

The wires are 15" in length

for DESA: Dayton, Knipco, Koehring, Master, Reddy, Remington, Sears, TSC: (PP236, M16656-23, M1665623, M16656-24, M1665624)

Connects from the main control valve to supply the pilot flame

Round orifice included

Length: 4" Long

Compatible with 80472

Voltage: 115 VAC 60 Hz

Warranty: 1 Year

PP204, HA3004, 1/2" Rotor Kit and PP214 Filter Kit

Rotor Kit 1/2" Thick Dia= 2 1/8", Desa part# PP204, GHP part#SP-KFA1000, Mi-T-M part# 68-3043, Pinnacle part# 70-022-0100;PP214 HA3017 Air Filter Kit #71-054-0300

Fits:DESA Brands Dayton,Master, Knipco, Koehring, Master, Reddy, Remington, Sears, TSC Heaters Parts

1-RPM (Clockwise rotation facing the shaft - Reversible mechanically), 120-Volt, 0.51 Amp, Spade Terminals

3/8" X 1" SHAFT - 3/8" Diameter Output Shaft with 1" Extension (***No hole in shaft for pin***)

HEAVY DUTY - Zinc die-cast housing and high temperature spherical bushings

Long Lasting Cotton/Fiberglass Construction

Burn-Free Fiberglass Top Never Needs Trimming

Super Absorbent Cotton Base for Consistent Fuel Flow

Complete burner for tall patio heaters with 2 1/2" Pole

Piezo striker. Sheild mounting hardware not included;Emmitter Screen 3 post

Main control valve. Pre-attached 5' Hose and Regulator

FREE Tech Support. Use amazon messager to contact Seller.

RPM: 1500 ; Voltage: 115 VAC 60 Hz

30 Day Return Policy

The 120630-01 Pilot ODS assembly was used on many of the unvented Natural Gas Gas wall heaters and NG unvented gas log sets and fireplaces.

The 120630-01 Pilot ODS assembly take the 120790-01 Dual Wire Thermocouple. The 120790-01 Thermocouple Dual Wire 33 Inch Length with silver and brown transmitter wires that fits the Desa International Unvented Vent-Free infrared gas wall heater.

Many of the Unvented Gas Logs sets, Wall Heaters and fireplaces that used the 120630-01 Pilot ODS were made by DESA International and sold under many different brand names by Lowe's, Ace Hardware, Home Depot, Sears, Menards Store and other retailer throughout North America.

Aftermarket Harman Convection Blower - Premium

Fits Harman Pellet Models: ~ Accentra Cast Freestanding ~ P35I ~ XXV ~ XXV-TC

Part # 1-00-29145 / 3-21-29045

The wire used in the heater are all high temperature resistant silica gel wire, and the temperature resistance is more than 200 C.

This heater is suitable for small space heating, dehumidification and warmth preservation within 0.5 cubic meters.

The service life of the heater is long. The general standard is that the power attenuation after 3 years is less than 10%.

Use with pellet appliances

Stainless steel inner walls and galvalume outer walls

1in clearance to combustibles

PREMIUM QUALITY REPLACEMENT PARTS - Manufactured with high-quality materials that exceed OEM standards. The dump switch is made of heavy-duty ABS plastic while the thermocouple components are made of high-standard red copper and brass. Easy to install and use, this replacement kit will allow you to enjoy your space without worrying about your safety.

GUARANTEED PROPER FIT - Our replacement parts are highly compatible with different models of propane gas heaters including propane patio heaters, indoor room gas heaters, and thermoelectric gas heaters.

UNIVERSAL M8*1 THREAD THERMOCOUPLE - The patio heater thermocouple wire has a full extension length of 350mm with temperature resistance sleeves. It has an M8*1 fixed thread head with end thread nuts that are compatible with 8mm gas valves.

Part numbers：PP200, HA1000, 102548-01, 102548-02, 102548-03, 102548-04, 102548-05, 102548-06, 102548-07,PP200SC

Fits All-Pro,Desa,Dayton,John Deere,Master,ProCom,Reddy,Remington,Sears ,and many others models.

This is our newest PP200 Heavy duty silicon nitride version.

[FITMENT] Thermocouple replacement for most brand of tank top heater like Mr Heater, Dura Heat, COSTWAY, REMINGTON, ProCom etc. (Not suitable for Texsport heater or similar main control valve).

[REPLACE PART NUMBER] 2304885 Thermocouple Replacement of Mr heater thermocouple model and work for the propane tank top heater. When the heater won't light up, you need to replace it with a thermocouple ( some times the problem is the gas valve defective so you need replace valve).

【COMPATIBILITY】Compatible with Mr. Heater MH15T, MH15TS, MH30T, MH30TS, MH45T. Compatible with Sunrite SRC15T, SRC30T. Compatible with GHP RMC-FA50/C/L RMC-FA60/L/L-01 RMC-FA100/C/L RMC-FA125/L/L-01. Compatible with other model FA40DGD, FA40DGP, FA40DGP-01, FA50DGD, FA50DGP, FA50DGP-01, FA60DGD, FA60DGP, FA60DGP-01, FA100DGD, FA100DGP, FA100DGP-01, FA125DGD, LPFA125DGD, FA125DGP, FA125DGP-01, FA150DGD, FA150DGP, FA150DGP-01.

🔧TROUBLESHOOTING FOR BRECKWELL PELLET STOVE IGNITER- lgnition problems nearly ALWAYS have something to do with a dirty stove. Make sure your stove, the venting and the clean-out area inside the burnpot cavity where the igniter resides are free and clear and inspect your door gasket and your door latch are in good sealing condition.

EASY INSTALLATION AND STURDY MATERIAL: The lgniter element is used on all Breckwell models of Pellet Stoves from 1998 to present. Replacement Part Models: C-E-IGN, 80607

PERFECT REPLACEMENT FOR YOUR OLD BRECKWELL PELLET STOVE IGNITER PARTS - Compatible Model: P20 Cadet ~ P22 Maverick ~ P23 Sonora ~ P23I Sonora Insert ~ P23I Sonora Insert ~ P24 Blazer ~ P24I Blazer Insert ~ P26 Cadet~ P32i Cadet ~ P1000 Big E ~ P2000 Tahoe ~ P2000I Tahoe Insert ~ P2700 Mojave ~ P4000 Classic Cast ~ P6000 Heartland ~ P7000 Solstice, etc.

Fits models GSD2210, GSD2211, GSD2845 and GSD2846; Also fits similar Pleasant Hearth models

Improves whole room heating

Requires 120V grounded power outlet

Fits Englander Models: 10-CDV - 25-CB120 - 25-EP & 25-EPI (Evolution Pellet) - 25-IP (Imperial Pellet) - 25-PAF - 25-PAH (Pellet Auxiliary Heater) - 25-PDV - 25-PDVC - 25-PFS & 25-PFSP - 25-PI - 25-SSP01 - 55-SHP10 - 55-SHP20 - 55-SHP22 - 55-SHP25 - 55-SHPAH - 55-SHPCB120 - 55-SHPEP & 55-SHPEPI - 55-SHPIP - 55-SHSSP01 - 55-TRP20 - 55-TRP22 - 55-TRP25 - 55-TRPAH - 55-TRPCB120 - 55-TRPEP & 55-TRPEPI - 55-TRPIP - 55-TRSSP01

Complete Assembly with Housing and Docking Gasket.

3000 RPM, Clockwise Rotation. 120V AC, 60Hz.

Gas Heater Replacement Thermocouple for Desa LP Glow Warm, Comfort Glow, Blue Flame Vent-Free Heaters

Overall Length: 39.5 inches made of Copper Polished with End connection Nuts: M8*1,Temperature resistance 650°C + on Head with 30 Minivolt Thermocouple.

Openning Valve time: ＜10s, CSA certified parts ,This model will fit the following Comfort Glow Vent-Free wall heater & Blue-Flame Vent-Free Natural Gas Heater wall heater

Applications: For Desa Oil Heaters with Hot Surface Ignition (glow plug)

Space Heater Replacement Parts PP236 Photocell For Reddy Remington Master Knipco Heaters M16656-24

PP236: Photocell Assembly should be used with 104068-02 ignition control boards on oil fired heaters.