Best Jet Table Saw Accessories in 2026

We have all been in a situation where we need to quickly turn the power off on our router table or contractor table saw and both of our hands are a bit pre-occupied. Reaching down and underneath your router table or contractor table saw to try and locate the power switch can be very cumbersome as well as very dangerous while your feeding stock through.Many router table setups don’t even have an external power switch separate from the router itself.

With this uniquely designed and easy to locate Paddle Button Stop Power Tool Switch you can simply bump the large stop sign paddle with your knee or hip to shut the power off. That means both of your hands can stay engaged on the project while you bump the power off with your hip or knee. A large green START button is always visible on the top side of the paddle. Simply push the START button to power on.

Install the switch near or at hip level or in a position that you will be able to bump it when needed. The switch comes with installation hardware and can be mounted to most any type of material. The unit has two cords. The heavy duty female cord is 18” long and designed to accept the power source plug from your power tool. The heavy duty male cord is approximately 66 inches long and is used to plug the switch unit into your standard wall outlet.

Push blocks are designed to be one of your essential safety devices to help provide protection and prevent your fingers from getting too close to cutters or blades on a router table, band saw, shaper or a jointer. Push blocks work well in multiple situations throughout your woodworking projects and are intended to be used any time your fingers are close to being in harms way.

Push blocks can be used one at a time like when feeding stock through your router table with a fence or you could use two at a time for extra downward pressure like when you would feed stock through on a jointer. They also work well on band saws for re-saw applications and can also be used on shapers much in the same way they are used on router tables.

This Push Block has been intentionally made in a bright SAFETY ORANGE color for high visibility when in use. This provides the user the ability to see exactly where their hands are at during the cutting or milling process. The bright SAFETY ORANGE color also allows you to easily find the device when it’s not in its normal location.

The Fulton Miter Gauge is a high quality, well thought out and economical solution for your table saw cross cutting needs.The Aluminum Miter fence is equally well thought out with its 45 degree ends for unsurpassed workpiece support and its ability to mounted to most any miter gauge. Also included is a handy aluminum flip stop for repetitive angled cuts on your table saw. Together these three items are the perfect compliment to each other for your table saw cutting needs.

The .200” thick, adjustable, solid aluminum head is machined with 13 positive stop holes. 1 hole is at 90 degrees while the 6 holes on both sides are at 22.5, 30, 45, 60, 67.5 and 90 degrees. The positive stops are perfect for many woodworking projects as they are the angles that are typically used.To adjust the head you simply loosen the post knob handle, pull the spring loaded indexing pin outward, rotate the head to the desired position, release the pin and lock into place.

The head is mounted to a solid steel miter bar that measure 18” in length and is .354” thick by .730” wide. Standard miter slots are 3/4” x 3/8” with a 1/8” “T” slot (slight variances from brand to brand) running the length on the bottom of the slot. The steel miter bar is equipped with a metal, removable retaining disc that measures 7/8” in diameter and is just shy of 1/8” to fit into to the “T” slot to prevent accidental lifting when feeding your stock through.

If you own a table saw and you need to make a crosscut at any angle then you know how valuable a miter gauge can be. You may also know that the miter gauge that came with your saw is not terribly accurate or durable. Not to mention that the fit in the miter slot may not be all that great as well. The Fulton Miter Gauge is a high quality, well thought out and economical solution to your table saw cross cutting needs.

The .200” thick, adjustable, solid aluminum head is machined with 13 positive stop holes. 1 hole is at 90 degrees while the 6 holes on both sides are at 22.5, 30, 45, 60, 67.5 and 90 degrees. The positive stops are perfect for many woodworking projects as they are the angles that are typically used.

To adjust the head you simply loosen the post knob handle, pull the spring loaded indexing pin outward, rotate the head to the desired position, release the pin and lock into place by tightening the post knob handle. The aluminum head has two ¼” x ½” slots milled into it for mounting a miter fence if so desired. The slots are approximately 1-1/8” from the base of the miter gauge head.

If you own a table saw, you probably have come across a situation or two where you need to make smaller cuts or make cross cuts. You may also have had the need to make repetitive cuts of the same length. Making small cuts, cross cuts and repetitive length cuts is where table saw crosscut sleds excel. Crosscut sleds help stabilize the work piece and are very accurate since they are essentially calibrated to your saw during the sled building process.

Some time ago we noticed a lot of companies had UHMW bars available for purchase. While we as a woodworking company know exactly what they are used for, many novice or non-woodworkers do not. That’s when we decided to create this package with pre-cut UHMW bars, pre-cut aluminum track, a knob and bolt and an easy to understand how to guide booklet so you can create your very own, custom crosscut sled to fit your table saw!

UHMW bars are most commonly used as runners for crosscut sleds since they don’t produce as much friction as wood does. Another advantage is that UHMW won’t expand or contract like wood does during drastic weather changes. Each bar is approximately 3/4” x 3/8” which fits most standard table saw slots. UHMW bars are also slick and won’t leave any residue, dust or shavings behind like wooden bars tend to do.

Insert Dimensions: 12-1/2” x 3-9/16” x 7/16” - JT-164 Jet/Powermatic 64A Zero-Clearance Table Saw Insert

Made from high-density phenolic laminate with a bonded-melamine surface

Small Jet, Grizzly, Powermatic 64 insert will fitvarious models of table saws.

Insert Dimensions: 14”x 3-3/4” x 3/16"

Made from: Phenolic Material

New Craftsman / Rigid insert (4131) fits various models of table saws

Insert Dimensions: 14-3/8” x 3 3/4” x 3/16”

Made from: Phenolic Material

Older Craftsman insert (4132) fits various models of table saws.