Best Aluminum Current Switches in 2026

Simple Operation:Switch on = Power; Switch off = No power.Rating: 275A DC Continuous (1hr), 455A DC Intermittent (5 min), 1250A DC Cranking (10 sec); Stud Size: 2x3/8" (10mm)

Durable Material: This battery disconnect switch is made of ABS plastic housing, tinned copper studs and nuts.Come with 4 stainless steel mounting screws and caps to help fix the switch tightly. 4 Removable side plates provide access for battery cables

Safety Protection:battery shut off switch can disconnects the battery safely, protect batteries from excessive drain when vehicle or boat is not in use

1.Size: 6 x 6 x 4.3mm / 5mm / 6mm / 7mm / 8mm / 9mm / 10mm / 11mm / 12mm / 13mm

2. Contact Type: Momentary Contact; Current Rating: 50mA; Voltage Rating: DC 12V; Contact Resistance: 100M Ohm

3. High Quality: Flame Retardant Plastic and Stainless Steel High Life Reed

Single Pole Double Toggle Switch - This Single Pole Double Toggle Switch resists corrosion.

Single Pole Double Toggle Switch features include:

Single Pole Double Toggle Switch 15A 120V

Working Condition: The working condition for the battery switch is 12V-60V voltage and 0-300A

Applications: The battery disconnect is always used as a key part to cut off the current from the battery when it is not working. The switch can be applied to many marine boats RV ATV vehicles and other 12V-60V battery devices.And the switch have four buttons in total, 1-2-both-off. It will separate the battery easily and will let you control the power more convenient.

Material: The battery switch outer shell is made of ABS panel and bolts are galvanized, which is totally rust and corrosion resistant.

Attention: It is a Momentary Push Button Switch: Push & Hold, ON; Release, OFF, Contact Configuration: 1NO 1NC

Brand All New Design Silver 10A Stainless Steel Ring LED Pushbutton Switch; LED voltage: 12V only, Hole size required: 7/8''/22mm

4.8 mm wide X 0.8 mm thickness Terminal Pin for High Current Use; Longer work life: Electrical life: 500,000 times. Mechanical Life: 2,000,000 times.

Single ON/OFF Switch: 5 Independent ON/OFF switch, this aluminium panel switches can control 5 devices at the same time. 5 gang 3 pin switch blue illuminated, these switches not be signed and you could assign the switches at your needs. Good for both 12V and 24V vehicle.

Safe and Short Circuit Protection: Built with overload protection, easy replace, protect panel from over-heating, over-current, over charging， overvoltage and short circuit. IP65 waterproof, no need to worry water when in boat or ship, safely protecting with anti-reverse, very convenience for using.

Easy to Install: Installation is easy and can be mounted horizontally or vertically, switch panel comes with 4 pieces stainless steel mounting screws, helps to install the switch panel firmly according to your needs.

ATTENTION: This is a Momentary Push Button Switch! Push & Hold, ON; Release, OFF, Contact Configuration: 1NO1NC

Brand All New Design Silver 10A Stainless Steel Ring LED Pushbutton Switch; LED voltage: 12V only, Hole size required: 7/8''/22mm

4.8 mm wide X 0.8 mm thickness Terminal Pin for High Current Use; Longer work life: Electrical life: 500,000 times. Mechanical Life: 2,000,000 times.

OPERATION: You will get 1 Battery Disconnect Switches, 2PCS Keys, 1 Waterproof Cover,4PCS Copper Ring Terminals and 4PCS Heat Shrink Tubings. This battery kill switch is used for DC 12V 24 V systems, On/Off 2 position, Continue current: 100A. Intermittent current: 750A (5 min).

DIMENSION: 2 brass terminals: 5/16", 2 mounting holes: 3/16". The base is 2.35” in diameter, the post that holds the key stands up 1 1/4” from the base, and it’s diameter is 7/8”

WATER-RESISTANT: This battery master switch comes with 6 keys and 2 weather covers. The red keys can snug fit to curb battery drain and theft. The black cover can prevent from dust and water, prolong their lifespan

【Compatible】- The battery disconnect switch is used for top post terminal(0.59''- 0.67'' cone battery negative post only). Compatible the condition of 12V voltage, 125A rated current, heavy duty.

【High Quality】- Our solid brass 12v battery disconnect switch with stainless steel fasteners provide excellent oxidation resistance and corrosion resistance, no need to worry about its service life.

【Easy to Use】Knob type design to disconnect or connect battery, just follow the direction instructions on the switch, unscrewing or tightening the battery switch into an “on” or “off” position to control current.

HCDC HD060 Automatic transfer switch, an easy to mount 15Amp inline transfer relay provides switching between AC INPUT 2 (Utility or Shore Power) and AC INPUT 1 (Inverter or Generator) AC source. When AC INPUT 2 is powered, the load power will be switched to AC INPUT 2. When AC INPUT 2 is powered off, the load power will be switched to AC INPUT 1.

Operating voltage AC 90 to 135V 50/60Hz. Maximum current 15 Amp. Transfer time less than 30mS (0.03 second). For most smart devices or computers, the switching action of 30mS time will not affect their normal operation.

Internal four high power SPST relays switch design, effectively avoid the problem of DPDT relay high inductive load arcing. Live and Neutral wire are switched at the same time. The Ground wires of the two inputs and output are connected together internally and will not follow the switch on and off.

Brand All New Design Silver 10A Stainless Steel Ring LED Pushbutton Switch; LED voltage: 12-24VDC only, Hole size required: 0.74''/19mm

19mm Momentary Push Button Switch: Push & Hold, ON; Release, OFF, Contact Configuration: 1NO

High quality metal material & IP65 waterproof protection can be used in wet or dusty enviroment.

[Parameter] - Modle: FS-1; Material: Iron; Rated voltage: 250V; Rated current: 10A; Contact: 1NO 1NC; Cable length: 1m

[Features]- The shell is made of flame retardant material, which is not easy to be damaged, the internal switch core is silver contact, anti-corrosion, internal thickened pressure spring, anti-oxidation square steel shaft, corrosion-resistant

[Function]- This foot switch is an instantaneous action, can be connected to push or push, can be used in industrial equipment and other fields that require foot switches. Keep pressing the pedal to turn on the device, and release the pedal to turn off the device

[Parameter] - Modle: FS-1; Material: Plastic; Rated voltage: 220V; Rated current: 10A; Contact: 1NO 1NC; Cable length: 0.1m

[Features]- The shell is made of flame retardant material, which is not easy to be damaged, the internal switch core is silver contact, anti-corrosion, internal thickened pressure spring, anti-oxidation square steel shaft, corrosion-resistant

[Function]- This foot switch is an instantaneous action, can be connected to push or push, can be used in industrial equipment and other fields that require foot switches. Keep pressing the pedal to turn on the device, and release the pedal to turn off the device

Type: 22mm 7/8" Silver shell Green light Self-Locking Push Button Switch ON/OFF; Connector type: SPDT,2 position 6 pin ; Rated Voltage & Current : 10A 12-24V DC.

Material:Enclosure Stainless Steel; The base adopts flame retardant PA66; Protection level IP65 can be used in wet or dusty enviroment, With jumper terminals for easy installation and modification.

Wide application:Suitable for boats, trucks, cars, electric motorcycles, RVs, Also very suitable for DIY tasks etc.

Our Push Button Switch through UL certification and CE certification.Waterproof IP67 can be used outsides or marine applications such as ships. Stainless steel 304 shell is sturdy and durable.

Rated current 5A 250V, Stainless Steel Ring LED, Hole size required: 7/8''/22mm.,LED light:12V (AC/DC), Mechanical life: 1,000,000 cycles,Electrical life: 100,000 cycles.

22mm Latching Push Button Switch: Latching switch: Push it =ON; Push it again =OFF, Contact Configuration: 1NO1NC(SPDT), 6 pins.

Our Push Button Switch through UL certification and CE certification.304 Stainless Steel material & IP67 waterproof protection can be used in wet or dusty enviroment.Switch Name: J22-271

Head: Flat round; LED voltage: 110~120V AC/DC, Hole size required: 7/8''/22mm. LED Life:40000 hours.Thermal Current: 5A ,Maximum Voltage: 250V AC, Minimum Voltage: 5V DC, 1mA

22mm Momentary Switch: Push & Hold, ON; Release, OFF, Contact: 1NO1NC(SPDT). When Rated voltage is 110V AC, resistive load is 5.0 A, inductive load is 3A.

Toggle Switch 4 Way - This 4 Way Toggle Switch installs easily.

Toggle Switch 4 Way features include:

4-Way Toggle Switch 15A 120/277V

Our Selector Push Button Switch through UL certification and CE certification.High quality metal material (Stainless Steel 304 )& IK10/IP40 protection.

Item Name:Selector Switch J19-572,Contact Type:2NO 2NC DPDT,Selector Positon:90°3 Position.Action Type:Latching.

Mounting Hole Dia:19MM /0.75", Rotary switch with light: 24V Blue LED.Easy to install,with the wire connector.

Specifications: You will get a Brand New Red Aluminium Mushroom Head Push Button Switch.The rated voltage of this switch is: 250V AC, rated current: 5A, required aperture: 0.63''/16mm.

Function: Mushroom Momentary Push Button Switch.The switch is compact and operates quickly and gently.

Design: The button switch operation type of this product is Momentary, keep pressing and holding the button = ON, hand off the button = OFF).Contact Configuration: 1NO.

Specifications: You will get a Brand New Green Aluminium Mushroom Head Push Button Switch.The rated voltage of this switch is: 250V AC, rated current: 5A, required aperture: 0.63''/16mm.

Function: Mushroom Momentary Push Button Switch.The switch is compact and operates quickly and gently.

Design: The button switch operation type of this product is Momentary, keep pressing and holding the button = ON, hand off the button = OFF).Contact Configuration: 1NO.

Specifications: You will get a Brand New Green Aluminium Mushroom Head Push Button Switch.The rated voltage of this switch is: 250V AC, rated current: 5A, required aperture: 7/8''/22mm.

Function: Mushroom Momentary Push Button Switch.The switch is compact and operates quickly and gently.

Design: The button switch operation type of this product is Momentary, keep pressing and holding the button = ON, hand off the button = OFF).Contact Configuration: 1NO.

Specifications: You will get a Brand New Black Aluminium Mushroom Head Push Button Switch.The rated voltage of this switch is: 250V AC, rated current: 5A, required aperture: 0.74''/19mm.

Function: Mushroom Momentary Push Button Switch.The switch is compact and operates quickly and gently.

Design: The button switch operation type of this product is Momentary, keep pressing and holding the button = ON, hand off the button = OFF).Contact Configuration: 1NO.

MAIN SPECIFICATIONS AND TECHNICAL DATA - Shopcorp Switch Control Box offers a double (2) hole push button with a 22mm button hole size and a screw hole diameter of 4mm. Surface mounted, waterproof sealed plastic electrical enclose push button box. The XB2-B01 empty plastic control station with 1 opening in 1 column is part of the XB2 range offered by Shopcorp. No batteries required.

WORKING CONDITION - Max Current: 10A; Max Voltage: 220V; Interface: Momentary Pushbuttons; Number of Buttons: 2; Contact Operation: 1NO/1NC; 1-Row vertical; Material: Polymeric (Plastic); Use With: Stainless Steel Lid Mounting Screws. Ambient temperature: between -25°C and 55°C; Protection Level: IP65; Certificate: CCC CE.

VERSATILITY - The push button switch control box can be used in a control station in order to protect the push button switch. Suitable for industrial control equipment circuits for controlling electromagnetic starters, contactors, relays and other circuits (there are only boxes in here, button switches are not included). Good for electronic projects, power supply units, amplifiers, etc. Suitable for emergency stop rotary switch.

GET NEW ONE IF NOT MAN MADE BROKEN IN 3 YEARS SINCE YOU PURCHASE THE SWITCH.

Brand All New Design Silver 10A Stainless Steel Ring LED Pushbutton Switch; LED voltage: 12V only, Hole size required: 7/8''/22mm

22mm Latching Push Button Switch: Push it, ON; Push it again, OFF. Contact Configuration: 1NO1NC

Connect power and Gigabit Ethernet data to 8 PoE-enabled devices, with 30W per-port output

8 Port Unmanaged Industrial Gigabit Power over Ethernet Switch

802.3af / 802.3at PoE+ Switch

Wide Application: Rated Current: 6 A, Rated Voltage: DC 12V PWM Dimmer, the dimmer switch is applicable to dimmable LED lamps, LED rope lamps or strip lamps, halogen bulbs, incandescent lamps, and DC 12V circuits used for dimmable LED lamp control, such as RV, truck, van trailer, boat, camper, etc

Memory Function: You can adjust the light by pressing the button, long press to adjust the brightness, short press to turn on or off the light, turn off the power and turn it on again, and the light will maintain the last brightness

Adjustable Backlight Design: The led dimmer switch has soft blue light, when it is dark, you can easily find the switch through it, you can also choose to turn on or off the backlight according to your needs