Best Handheld Lcr Meters in 2026

This LCR Meter is a 19999/ 9999 counts dual display, high accuracy LCR meter, which could measure Inductance/ Capacitance/ Resistance with secondary parameters including dissipation factor (D), quality factor (Q), phase angle , equivalent series/ parallel resistance (ESR or Rp).

This LCR Meter is fully auto ranging operation for AC impedance & DC resistance measurement. The user could measure the L/C/R components directly in “AUTO-LCR “ smart mode without selecting the function key.

Components could be measured in serial or parallel mode according to the DUT (device under test) impedance automatically.User could select the desired test frequencies of 100Hz/120Hz/1kHz/10kHz /100kHz.

✅【High Quality & High Accuracy】The tester is automatically identified the passive component.Precision LCR Meter 6000 counts with the range of Resistance:600Ω~60MΩ；Capacitance：9.999nF~99.99mF; Diode Test:Open Voltage:3.0V,Testing Current:1.5mA;0.1% Accuracy.

✅【Non-rusting】The entire outer surface of the tester case has been with thermo plastic elastomer, and Spare Test Pin are included which has been gold-plated, so that can be reduce pin contact resistance and prevent it from rusting.

✅【Wide Range of Application】With the function of the continuity and Diode Test,you can used it for many applications,such as components verification and sorting, production lines, laboratory and service center, in-field repair，battery power test and more.

✅【Anti-rust Material】The whole test box has thermoplastic elastomer on the outer surface, with gold-plated spare test pins, which can reduce the contact resistance of the pins and prevent them from rusting.

✅【High Precision】Automatic identification of passive components, precision meter 6000 times, resistance range: 600Ω~60MΩ; capacitance: 9.999nF~99.99mF; diode test: open voltage: 3.0V, test current: 1.5mA; precision 0.1%.

✅【Auto Power Off】If the tester is idle for more than 15 minutes, the tester will automatically turn off the power.HOLDPEAK 990 SMD tester is a handheld and battery operated compact tool that is very convenient to operate and easy to measure SMD.

UNI-T UT622E LCR meter. 99,999 maximum reading with high accuracy up to 0.1%. Test frequency (100Hz, 120Hz, 1kHz, 10kHz, 100kHz). Test signal level (0.1Vrms, 0.3Vrms, 1Vrms). Maximum test speed: 20 times/s. Constant 100Ω output impedance. Auto LCR. DCR test rate. Fast (20 times/s), medium (5 times/s), slow (2 times/s)

2.8-inch TFT LCD display. High-brightness white backlight. Data hold. Recording mode. Standard Mini-USB communication interface. SCPI command set. Perfectly fit the measurement and screening of inductance, capacitance, and resistance in production lines, maintenance points,etc.

Built-in rechargeable battery with large-capacity. 8h long battery life. For evaluation of resistance, parameters of capacitors, inductors, magnetic cores, resistors, piezoelectric devices, transformers, chip components, network components, circuit boards, relays, switches, cables, batteries, etc.

👉【One hand use】Easy operation, full set of shortcuts.

👉【Automatic LED Testing】Test Voltage up to 25V(Others brand2.5V only).

👉【Wide measurement range】R: 0.1Ω to 60MΩ / C: 0.1pF to 99.99mF

This set includes DE-5000 itself TL-21 Alligator Test Lead Case TL-22 SMD

Line ISO 9001 Auto L.C.R. check 100 / 120 / 1k / 10k / 100k Hz test frequency 20,000 / 2,000 counts

counts display Backlit Ls / Lp / Cs / Cp / Rs / Rp / DCR with D / Q / θ / ESR measurement Relative

Replaced by the More Accurate DE-6000

Wide Range of Selectable test frequencies: 100 Hz / 120 Hz / 1 kHz / 10 kHz / 100 kHz

Allows for 4-Wire Kelvin Measurement to factor out impedance of test leads

LC200A portable meter is based on the LC resonant principle, adding high-speed micro-controller precision measurement calculation. The meter has wide measurement range and high precision, it's measuring range is below 1uH and 1pF. Wide measurement range, high accuracy, small size, light weight and portable.

LC200A series can be powered by mini USB cable or included Φ5 DC power supply cable. Note: The power supply voltage is 5V. You can also install 4 AA batteries to power the meter. If the meter is not used for 5 minutes when it is battery powered, it will automatically turn off the power.

There are five buttons. They are reset button in red, Hi.C, Hi.L, L/C and extended FUNC button in blue. Just press red the button to calibrate. Open circuit calibration in capacitance measuring mode. Short circuit calibration in inductance measuring mode.

【Correction function】The inductance capacitance meter has a clear correction function. The capacitance mode is used for open circuit correction, and the inductance mode is used for short circuit correction

【Wide use】The multimeter with capacitor is widely used in scientific research and technical engineering, factory electronic instrument testing, electronic instrument maintenance, school laboratory teaching, electronic design, etc.

【Frequency display function】The inductance capacitance multimeter has a frequency display function: when measuring the component under test, you can view the current measurement frequency

40,000 counts resolution on primary and 10,000 counts resolution on secondary display

L, C, R, and Z (879B & 880 only) primary measurements

Automatic calculation of secondary parameters D, Q, Theta, ESR (Theta/ESR for 879B &880 only), and DCR (880 only)

Our digital LCR meter supports electrolytic capacitance measurement, screening and deviation measurement and automatic recognition of component measurement.

Test frequency of the resistance tester is: 100Hz, 120Hz, 1KHz, 10KHz, 40kHz, 100KHz; Basic accuracy is 0.30%.

With large capacity lithium battery power supply and USB port, our handheld LCR meter is portable and can work for long time.

【Appearance ; parameters】2.8-inch TFT display, 4-bit semi-display; Display digit: Main parameters: 5 bits, secondary parameters: 5 bits；Test Frequency 100Hz-100KHz continuously adjustable, 1Hz step; Basic accuracy: 0.20 percent

【Easy To Use】Supporting DC Resistance and Electrolytic Capacitance Measurement; Automatic Recognition of Component Measurement; Support screening and deviation measurement;

【Other ;Functions】Adjustable measuring speed, manual and automatic range; Short circuit correction with open circuit; Provide multiple test ports.

The color of the casing shipped by Amazon is yellow, don’t buy it if you mind, the next batch of goods will be blue casing

Precise Frequency Control: Adjust the frequency from 100Hz to 100KHz with 1Hz increments.

Automatic Component Recognition: The device automatically recognizes and measures components.

DE-5000 LCR Meter

TL-21 Test lead

TL-23 Guard line

Hard Case for DE-5000 & accessories

the film perfect suit for the screen

Equipment and accessories not included

【POCKET SIZED】Unlike the traditional multi meter, this digital tester is portable and handheld, tweezers-form with various test functions, allowing you to perform the test work at anywhere and anytime.

【MULTI FUNCTIONAL】Small size but powerful, by a simple grasp, the tester will automatically identify for resistor, capacitor, inductor, voltage, frequency and/or diode of electronic components and will actively select the appropriate range to measure.

【DETACHALE PARTS AND 360° ROTATABLE】The entire digital tweezers can be separated into three parts: controller head, test arms and tweezers tips. The controller head is 360° rotatable, no matter if you are left handed or right, the OLED screen will always display the values at your right angle.

【100% Brand New and High Quality】The LCR Meter is automatically identified the passive component.It integrates a pair of tweezers like probes, a LCR meter and a LED tester into a single compact, lightweight, battery powered device. It is an all-in-one portable device that provides a simple and efficient solution for not only measuring SMD components, but also making in-circuit debugging.

【Non-rusting】The entire outer surface of the tester case has been with thermo plastic elastomer, and the two testing pins has been gold-plated, so that it is reduce pin contact resistance and prevent to get rusty.

【High Performance】If this ESR Meter is idle for more than 10 minutes, the tester will automatically turn off the power.SMD tester is a handheld and battery operated small Tool, very convenient to operate and it is specially used to measuring SMD.

【0.3% High Precision Measurement LCR Meter】It is used to measure the parameters of inductors,capacitors,resistors and other components.The measurement accuracy can reach 0.3%,providing you with accurate measurement data.It is simple to operate,after the components are connected,it can automatically identify the measuring components without manual switching.It is a portable handheld LCR meter that combines the convenience of handheld instruments and the good performance of desktop instruments.

【100kHz Test Frequency & 1/0.6/0.3Vrms Level】Handheld LCR meter includes 6 test frequency points, including 100Hz,120Hz,1kHz,10kHz,40KHz and 100kHz.The measurement frequency is up to 100kHz,and the 1Hz step is continuously adjustable.In addition, the handheld LCR meter can measure the levels of 0.6vrms and 0.3vrms,and can automatically select appropriate measurement parameters according to the characteristics of components. The measurement speed can be adjusted(fast/medium/slow mode).

【Open/Short Circuit Correction & Electrolytic Capacitance Function】Open/short circuit correction function can effectively reduce the error of distributed parameter caused by the test lines,and help to improve the measurement accuracy.The electrolytic capacitance function of the meter professionally measures electrolytic capacitor components with positive/negative electrodes,which can avoid capacitor damage caused by the measurement components when the positive/negative electrodes are unstable.

Continuously adjustable LCR meter in industrial &scientific

Lcr meter benchtop Testing frequency: 16 Points（100、120、200、400、800、1K、2K、4K、8K、10K、15K、20K、40K、50K、80K、100K

Capacitance multimeter support SCPI

【Multiple Accurately Measurements LCR Meter】LCR meter supports DC resistance, inductance, Measurement of impedance and capacitance measurement, automatic identification of component measurement, and screening and deviation measurement. LCR meter has 2 test level points, 6 test frequency points, measurement frequency is up to 100KHz, and accuracy is up to 0.2%. It can be widely used in electronic equipment maintenance, electronic engineering development, technology R&D and other fields.

【3 Measuring Speeds&TFT Color Display】LCR meter supports manual range and automatic range.There are 3 measuring speeds available for adjustment: slow, medium and fast.You can choose the appropriate measurement speed according to the nature of automatic components. LCR meter has a 2.8-inch TFT LCD color high-definition display with 4.5 digits. The screen has a backlight and the brightness is adjustable, so you can read accurately even at night. And the buzzer can be set according to your needs.

【Data Recording/Holding&Remote Communication】LCR meter holding function of capacitance meter is used to freeze the displayed data.The measurement is still in progress,but the data on the LCD is not be updated as the measurement proceed.In the reading hold mode,the maximum/minimum/average values can be dynamically obtained within a certain range.In addition,LCR Meter has remote communication function.Connect it to PC through Mini USB cable to realize remote control and data collection.

1. The measuring frequency is up to 100KHz, and the 1Hz step is continuously adjustable.

2. Support DC resistance, electrolytic capacitance measurement, support screening and deviation measurement.

3. Internal bias voltage output (10mV-500mV).

Power Supply: The meter can be powered by included Φ5 DC power supply cable and mini USB cable. You can also install 4×AA batteries. Each way makes the meter work. Note: the AA battery is not included.

Measuring Range: Capacitance 0.01pF-100mF, inductance 0.001uH-100H, frequency 500KHz/500Hz-50KHz.

High Precision: Accuracy 1% of capacitance range 1pF~1uF, 5% of range 1uF~100mF; 1% of inductance range 1uH~1H, 5% of range 1H~100H

【FUNCTION】The inductance meter can adjust the measurement speed, manual and automatic range; open circuit and short circuit correction; provide multiple test ports. There are 3 measurement speeds available for adjustment: slow, medium and fast.

【LONG SERVICE LIFE】The handheld digital LCR has a built-in 2600mAh rechargeable battery with low power consumption, providing you with longer usage time and longer standby time. The LCR meter offers 5/15/30/60 minute auto-off settings to help the device save power and extend usage time.

【EASY TO USE】Handheld digital LCR meter supports DC resistance and electrolytic capacitance measurement; automatic identification of component measurement; supports screening and deviation measurement. A foldable stand behind the capacitance meter allows you to easily view the data. The inductance meter is equipped with a silicone protective cover, which is shock-absorbing and anti-falling.

* 100Hz、120Hz、400Hz、1kHz、4kHz、10kHz、40kHz、50kHz、75kHz、100kHz 10 typical test frequency;（Hantek1832C)7 typical test frequency * 2.8 inch TFT LCD，Switch between Chinese and English * HD display，dual display of measurement data，the result is clear

* Support data record analysis * Support PC upper computer，easy to control and measure remotely * Test lead：3 end/5 end switch

* Measuring speed：high speed/intermediate speed/low speed switch * Range：support manual/auto switch，easy to do quick measurement

【Multiple Accurately Measurements LCR Meter】LCR meter supports DC resistance, inductance, Measurement of impedance and capacitance measurement, automatic identification of component measurement, and screening and deviation measurement. LCR meter has 2 test level points, 6 test frequency points, measurement frequency is up to 100KHz, and accuracy is up to 0.2%. It can be widely used in electronic equipment maintenance, electronic engineering development, technology R&D and other fields.

【3 Measuring Speeds&TFT Color Display】LCR meter supports manual range and automatic range.There are 3 measuring speeds available for adjustment: slow, medium and fast.You can choose the appropriate measurement speed according to the nature of automatic components. LCR meter has a 2.8-inch TFT LCD color high-definition display with 4.5 digits. The screen has a backlight and the brightness is adjustable, so you can read accurately even at night. And the buzzer can be set according to your needs.

【Data Recording/Holding&Remote Communication】LCR meter holding function of capacitance meter is used to freeze the displayed data.The measurement is still in progress,but the data on the LCD is not be updated as the measurement proceed.In the reading hold mode,the maximum/minimum/average values can be dynamically obtained within a certain range.In addition,LCR Meter has remote communication function.Connect it to PC through Mini USB cable to realize remote control and data collection.

20,000/2,000 Counts Dual Display

Auto LCR Mode for DUT Measuring

Parallel/Series Testing Mode

10 typical test frequency: 100Hz, 120Hz, 400Hz, 1kHz, 4kHz, 10kHz, 40kHz, 50kHz, 75kHz, 100kHz

Application: Measuring the parameters of the component such as inductance, capacitance, resistance and so on.