Best Karparts360 Tail Light Assemblies in 2026

Warning: Wires come out from the conner, NOT from the center. (Check image 2)

Partsam (7) Amber + (7) Red Oval Oblong Side Marker Light Lamps; It is Universal For all auto esp. RV Trailer Camper Boats etc. 【Tip: wires were brought out at the lower corner of the light and not the center,】

Can be function as Side Marker Lights, Clearance Lamps and Indentification Lamps, Trailer Lights etc.

Package incldues 2 Pieces White 7" Round LED Backup lights with reflex lens. Screws and thick mounting gaskets are included for complete mounting.

This is a 7 Inch Round LED Reverse lights which has 36 LEDs and works great for transit vehicles, bus, utility, and dome light applications. This 7" White LED Bus Tail Light is sonically sealed and waterproof with a surface mount light with mounting gasket. With the built-in reflex, the reflector in the center of the light can be visible from a long way off. They mostly works with the 7" round LED stop tail turn lights;

This 7 inch round back-up Light is 12V DC and is hard wired with separate ground wire: white is ground, black wire is dimmer for taillight/running light, and red wire is brighter for back up/revese lights mode. NOTE: These 7" School Bus lights can be used but they do not have flashing patterns. But with a proper relay it can be a flasher;

Direct Fit: for 2004 2005 2006 2007 2008 F150, 2007 2008 2009 2010 Explorer Sport Trac, 2006 2007 2008 Lincoln Mark LT; not for F-150 Heritage SVT Lightning or Explorer;

Bright Sparking LEDs: Full LED light source ensures great vision and brake/reverse indication, enhance safety during driving; LED 3rd BRAKE LIGHT REPLACE Part Number: 7L3Z-13A613-B;

IP65 Waterproof: This bake light case is padded with foam back and is perfectly sealed around. The foam gasket is designed for water-proof. As long as there is no gap between the car and the foam, water will not leak into your car;

Package includes 1pc Rear high mount third brake light, compatible with Silverado 1500 2500 HD 3500 HD and Sierra 1500 2500 HD 3500 HD 2007 2008 2009 2010 2011 2012 2013 Led 3rd Brake Light Tail Light Lamp and also replacement for Silverado 2500 HD 3500 HD 2014 and Sierra 2500 HD 3500 HD 2014;

About Silverado third brake light: Chrome Housing Red lens, Super Bright full LED lights. Don't have to worry about incandescent light bulbs blowing or fading overtime; Installation is easy, please clean the truck area and lip on light with alcohol. Then, attached to the light first. Rubber Washers are included; Note: please save your two screws because the screws are not included with the new lights. It will add a more modern look to your truck with LEDs instead of incandescent bulbs;

Waterproof: This Sierra third brake light includes 1pc foam gasket and is generally waterproof. Please kindly put a little silicone or some clear RTV all across the top to help seal it just in case it leaks into the light or where the wires are;

This listing is for 10 Pieces smoked 3/4 led marker lights(5 Pieces 3/4 amber led marker lights and 5 Pieces 3/4 red led marker lights). 60 lumen each marker light with single High Quality SMD LED Inside of the marker Lamp, offer you bright light with 50,000 hrs Life Time;

These 3/4 led lights are hardwired with 2 wires pigtails including lead and ground wires ensures for mounting to almost all surfaces: Black wire is ground and White positive; This 3/4" round Smoke Black lens LED lamp for use as a combination clearance light and a side marker light when properly mounted, for use with truck fenders or anywhere you'd like to mount them by drilling a 3/4" hole in a flat panel;

Function: led clearance lights, led marker lights, led side marker lights, led side fender lights, led front grill lights, identification lights, Trailer Lights, air dam lights, boat courtesy lights, auxiliary turn signal lights, auxiliary tail lights etc. NOTE: this smoked marker lights is sonically sealed for ip65 waterproof, please do not use it under water, thanks;

This square double face Pearl LED pedestal light is different form many of the pedestal lights on market, it comes with chrome bezel and visor, give you a outstanding look when driving on road; Work as Stop Turn Tail Park Brake and Side Marker Clearance Light; This light comes with clear lens,clear lens led lighting gives your truck a bright and clean look; Amber on one sides and red on the other side and amber side marker with Chrome Bezel and Visor;

High power pearl led lights are perfect for functional needs, great visibility and decoration. These double-faced square turn signal lights are a popular alternative to the factory incandescent style found on many truck fenders. We carry this light in many different styles, for plenty of choices. Our post-mounted LED lights are unmatched in quality and diversity. These durable LED lights have sonically sealed polycarbonate lenses and waterproof housings. operate within a 9-14.8 VDC;

Double Face Pearl Led Pedestal Lights: Red side serves 3 functions - stop, turn and tail light and Amber side serves 2 functions - parking and rear turn signal light; Built-in, amber side marker light with reflex reflector; 52 LED Super Bright Fender for each light (24 Amber LEDs &24 Red LEDs & 4 side marker Amber LEDs ); Heavy Duty Chrome Housing with Visor, Single Stud Mounting;

[Package Content] 2pcs 3x5 Rectangle Led Tail Lights, Grommet Mount and Hardwired with 3 wire pigtails;

[Features] This 5x3 Red Tail Lights features 12 pcs super bright LED's that will help enhance your car's visibility even on foggy days and keep you and your loved ones safe. Serves as stop light, turn light, tail lights. NOTE: we call it 3x5 Rectangle tail lights on market, but the actual sizes are as following: 5.14" x 3.27" x 1.00" (light only), 6.25" x 4.26" x 1" (overall size), drill a hole about 5-5/8" to install it. For more information, please check the image1;

[HARDWIRED WITH 3 WIRES] White Wire is the Ground; Red Wire is the high brightness as stop/brake/turn signal lights; Black Wire is the low brightness as tail/running lights;

Package includes 1 set LED Tail Lights Assembly Kit, compatible with 1976-1983 CJ5 tail lights, 1976-1986 CJ7 tail lights, 1981-1985 CJ8 tail lights, 1987-1995 Wrangler YJ tail lights and 1997-2006 Wrangler TJ tail lights. Driver Side and Passenger Side are included. Come and replace your dim factory tail lights with our brilliant LED tail lights assemblies and get eye-catching;

This rear combination tail lights kit feature 12 large brake, parking and directional LED's, 6 license plate light LED's, 21 brilliant white Back-Up LED's and 3 side reflector light LED's;

Partsam LED lights are a direct replacement for your stock tail lights. These rear LED lights are completely compatible with your electrical system, and the wiring tips are as below: White is ground, blue wire is for backup reverse light, black wire is for tail/license plate light/side marker light and red wire is for stop turn brake light;

Partsam ( 2 x Amber ) 3/4" Side Marker light Grommet Mount Single Led, Clearance Marker and Auxiliary Stop Tail Turn Light.

Led Side Marker Light, Fender Marker Light, Clearance Light, Indicator lights, Aux stop turn tail brake light etc.

Can be used as an aux lighting to your existing brake light, but not approved as a brake light.

Partsam Sealed 6" x 2" Amber Side Marker Light 13 Led Rectangle / Rectangular Light Surface Mount w/reflector

2" X 6" Unique Reflector Design; 11 LEDs facing straight ahead & 1 LED on either end, shining out the side; hole-to-hole distance:4.8"(approx);

6x2 Trailer-Style Rectangular LED Marker/Turn Signal Lights; The multi-faceted reflector creates the illusion of hundreds of tiny diodes sparkling behind the lens.

Package includes 4 Pieces 4 inch Round Led Stop Turn Tail Lights Red and 2 Pieces 4 inch Round Led fog back-up reverse Lights White, Round rubber Grommets and 3-prong wire pigtails are included for complete installation;

These Waterproof round led trailer lights 12 LED serves as the following functions: stop light, turn signal light,tail light(red lights) and Backup Lights or Reverse Lights(White lights); Recessed mount with rubber grommets and Pigtails and accepts standard 3-prong plug; These round tail lights are Approx. 5 inch Grommet Ring and 4" inner diameter and 1 3/16" Thickness, Please drill a hole about 4.5" to install; IP65 waterproof and please do not use it under water;

Easy to install: White is the ground, red is the high brightness and Black for low brightness; These 4 inch round led lights are impact resistant and less susceptible to shock damage. Each round trailer light is water-tight sealed. These LEDs draw less current, generate less heat and are brighter and light faster than an incandescent bulb; 12 Volt DC Input;

Partsam's High Quality Thin-design Smoke Black Lens Amber LED Led Marker Light, Stylish & Functional as side marker lights, clearance lights, indicator lights, identificaiton lights, utility lights etc.;

DC12V Each Light with High Quality 6 LEDs; Waterproof + Shock Proof + Viberation + Dust Proof; Brightness: 120 lumen each light with 6 pcs High Quality SMD LED 50,000hrs life span.

HARDWIRED WITH 2 WIRES and both lead wire and ground wire for mounting to all surfaces; The Black Wire is Negative/Ground and Yellow wire for positive. Light Dimension: 9.6cm x 2cm x 1cm (3.8" x 0.8" x 0.4") approx. Distance between center-to-center holes: 8.2cm (3.2") approx. Easy to Install with FREE Screw set included & Foam tape base.

Package includes 2 Pieces 11 LED 15" Ultra Slim Led Turn Signal Light Bar, CLEAR LENS AND AMBER WHEN LIT. This surface mount light bar is perfect for horizontal mount or vertical mount;

This 15 inch LED Trailer Turn Signal Light Bar is hardwired with 3 wires: White is the ground, red is high brightness for turn signal light and black is low brightness for tail light, parking light, clearance light or running light; NOTE: If you want to use it as strobe light, please buy a strobe module and connect,thanks;

Overall dimensions: Overall length is 15.5 inches approx.,overall width is about 1.3 inches, and the mounting holes approximately 14.5" Apart. The amber strip light bar is about half an inch thick, but with the little knob where the wires all come out, it's about 1 inch, so you may need to cut out a hole to allow that to go in. The spot knob is about half an inch in diameter. Really a nice slim low profile Waterproof LED trailer light bar;

Application: this led trailer lights kit is universal for heavy duty trucks, semi-trailers, cargo trailers, boat trailers work vehicles and any overland vehicle requiring quality DOT rated

kits include:2xRed 6" Oval Led Trailer Tail Lights grommet mount+2x2" Round 4 LED Amber led trailer marker lights 4 LED +2x2 inch red round led marker lights +14.17" 9 LED 3 light Red Clearance Light Bar(Truck Trailer Ideification light bar)

FEATRURE: NEVER change a bulb again. All weather proof, Votle: DC12v. Durable lens, protects against corrosin and fading, all weather resistant molded plastic housing. These LED lights are designed to be used in Trucks, trailers, tractors, semi-trailer, Dump, Surface mount design, mounts on any flat surface

Package includes 6 Pieces 6" Oval Red Led Stop Turn Tail Lights, Hardwired, not plug and play;

12V DC; Each 6 inch oval led tail light has 10 Led Diodes. These LEDs draw less current, generate less heat and are brighter and light faster than an incandescent bulb; Light Size: 6.3" x 2.2" x 0.8"; Rubber Grommet Size: 7.2" x 3" x 1.5"; Drill hole: 6.5" In.;

These 6 inch oval led trailer tail lights are HARDWIRED WITH THREE WIRES: White Wire--Ground; Red Wire--high brightness for stop/brake light; Black Wire--low brightness for tail/running light;

Round red/Amber light serves as brake light, turn signal, and tail light: Outer Ring of LEDs comes with dual modes(high low Beam) and function as tail brake lights; Center Clear/Amber LEDs act as turn signal and Parking light

Outer Diameter: 5.6"; Inner Diameter: 4"; LED Quantity: 16 LED (Inner Yellow 6 LED + Outer Red 10 LED); IP65 waterproof light fixture; Drill hole: 3.8" in.(int.)/4.2" in.(ext.);

Easy Installation With High Quality Durable Round Stainless Steel Ring, HARDWIRED with 4-WIRE connection system for Ground, Turn Signal, Brake Light and Running Light: Black Wire - Ground / Red Wire - Brake Light / Yellow Wire - Turn Signal Light / White Wire - Running Light/Tail light

Compatibility: These Full Amber Led Fender Side Marker Lights Replacements only suitable for Wrangler TJ 1997 1998 1999 2000 2001 2002 2003 2004 2005 2006 2007 Wrangler tj side markers. NOTE: These are aftermarket products. Pls check the compatiblity first before you buy;

Package includes 1 left (driver) side and 1 right (passenger) side Wrangler Signal Marker Lights Lamps Assembly, Amber Lens and White Led, other accessories not included. Part number: 55155628AC, 55155628AB, 55155629AC, 55155629AB, CH2550120, CH2551120;

Upgrade Design: different form those tj side blinker covers on market, these tj marker lamps are assembly with led lights. Each side marker built in 18 pieces 3528 LED Chips, provide super night visability of your vehicle on the road. And these side indicators built in reflex reflector lens, which removes the need for a separate reflector;

Partsam ( 2 x Red ) 6 inch Oval Led Stop Turn Lights Rear Brake Tail Lights 24LED with Rubber Grommets and 3-Prong Wire Pigtails;

LED Quantity: 24PCS; Voltage: 12V; Color: Red; Light Size: 6.3" x 2.14" x 1"; Size with grommet: 7.28" x 3.2" x1.1"; you need an about 6.4" hole to install it; Sealed & waterproof assemblies, PC lens and housing welded together to ensure a permanent and water proof seal; LED circuit board coated with conformal coating for excellent moisture and environmental protection;

HARDWIRED WITH THREE WIRES: Black Wire - Ground; Red Wire - high brightness; White Wire - low brightness; Please Kindly NOTE: We have 2 different types of this light: one with White wire for ground, and the other with Black Wire for ground. Both with red wire for high brightness and are of the same quality, and will not affect your usage,thanks;

Package includes 2pcs round double face sealed LED pedestal lights, which designed for trucks, towing & boat trailers, RVs, buses, ATVs, utility vehicles and also the heavy trucks.

4-1/8" Diameter round. Waterproof, dual-face light serves 5 functions: stop, front and rear turn, tail, and parking light. Front-facing amber lens and rear-facing red lens. Chrome housing. Single post mount.

dual-face design; 21 red LEDs; 21 amber LEDs; Miro-Reflex faceted reflector design provides increased light output and a contemporary appearance while maintaining a traditional footprint;

Package includes 2Pcs Universal Square 12V Combination 38 LED Signal Tail Light; Each one is equiped with 38 Super bright LEDs: 16 Red LEDs for stop/turn/tail functions, 18 White LEDs for backup function, 4 White LEDs for license illuminator; Both are set up for license plate lights as well as reverse lights;

These rear combination tail lights have studs on back sticking out will bolt to any flat surface; This is not a replacement for Wrangler YJ CJ JK tail lights, not factory mount. If you want to install it on wrangler trucks, you may need some modification: There is no wiring harness so you have to splice the wires yourself. Also, The bolt holes are larger than stock so you will need to drill out your body to make them fit. The entire assembly is a touch larger than stock as well;

DOT Compliant for street legal lighting. 12 volts; Low ampere draw; 3-stud mount design is easy to install on any vehicle exterior and the distance between the mounting blots is 2" ~ 2.2"; Resistant polycarbonate housing and acrylic lens provide weatherproof protection against water, shock & vibration;

Package Includes 4Pcs Amber 6-3528-SMD LED MARKER / CLEARANCE LIGHT, Supplied with decorative snap-on chrome plated bezel

4-1/3" ( L) x 1-4/5" (W) x 7/8" (H) (approx.) and The surface mount design features the industry standard 3.8" centres.; Used as side marker light, Clearance Light, Cab marker light, Identification Light, turn signal lights, Parking lights, running lights etc.

The PC lens, housing and LED circuitry are all sealed together by expoxy in a single unit to ensure a permanent, weather durable and waterproof seal.

High Compatibility-Direct replacement for all T10 wedge type W5W W3W 147 152 158 159 161 168 184 192 193 194 259 280 285 447 464 501 555 558 585 655 656 657 1250 1251 1252 2450 2652 2921 2825 PC 175 2886X.

Brighter- each T10 LED light bulbs with 10 x 3528 SMD chipsets LED, much brighter than regular LEDs with high power chips, ideal replacement for dull and yellowish stock bulbs

Long Lifespan- Built in quality high power beams, provide 20000 working hours long lifespan for the led bulbs.

Package includes 4 Pieces 4 inch round led trailer tail lights(2pcs red led lights and 2pcs white led lights) 12V DC, mounting screws and chrome rings are included. The chrome covers will dress it up very nice;

These round led tail Lights are impact resistant and less susceptible to shock damage. Each round LED Light is water-tight sealed and come with 15 bright LEDs. LEDs draw less current, generate less heat and are brighter and light faster than an incandescent bulb;

These 4 round led stop turn tail lights are HARDWIRED with 3 wires pigtails: Black Wire - Ground; Red Wire - high brightness(red as stop brake lights or turn signal lights and white as backup lights or reverse lights); White Wire - low brightness as tail lights or running lights;

Partsam includes 2 Pieces 15 Inch White LED Trailer reverse light Bar and 2 Pieces 15 Inch Red Led trailer stop turn tail light bar, 4 Pieces in total. Other mounting hardware not included;

Each 15 inch Led trailer tail light bar is powered by 11 high power LED for a bright performance. These Led Strip Bars are HARDWIRED with a three wire pigtail: white is ground wire, Black is the low brightness and Red is the high brightness. Functions of trailer led light bar: red led light bar functions as stop turn brake light in high mode and tail or running light in low mode; white light bar function as backup light bar or reverse light bar in high mode and side marker light in low mode;

Dimension of the trailer light strip: The overall length is about 15.5 inches, wideth is about 1.25 inch, and the thickness is about 0.5 inch. There is a little knob where the wires all come out, so the overall depth is about 1 inch, and you may need to cut out a hole to allow that to go in. The spot knob is about 0.57 inch in diameter. Really a nice slim low profile unit;

This smoke lens rectangular trailer light serves four functions: stop light, turn signal light, and taillight, and backup light in the center, this is white LEDs, but in clear lens in the center. It is a really nice low profile light for the back of your trailer or RV or motor home. In fact, it can make a really nice upgrade for any kind of vehicle that you're putting these on;

This taillight has a surface mount installation, so it mounts directly on the surface of your trailer, of your application, screws included for mounting. With two reflector strips built in top and bottom, it can be mounted oriented horizontally or vertically, whatever suits your application. Also a mounting gasket goes in between the light and the mounting surface, which creates a tight seal and offers some cushion behind the actual light;

This Triple LED Trailer Light is hardwired with 6 wires: White is the ground, Blue is backup/reverse light, green and yellow is high mode for stop or turn signals, black(with 1/3 yellow) and brown(with 1/3 green) is low mode for tail or running lights;

[High Intensity LEDs] This black Motorcycle tail light assembly comes with 19 high intensity LED chips. 16-2835 Red Light, 3-2835 White Light. Voltage: 12V. Material: PC Lens, PC+ABS Housing.

[Easy Installation] Remove the stock tail light, replace this new black tail lamp, insert the adaper into corresponding holes to make sure the new tail light works, and screw it up.

[Application] Compatible with Sportster Dyna Softail Touring Road Glide Road King Tail Light Assembly.

Package includes 5Pcs 3/4" Led Marker Lights 3 Wires in Red Lens, 3 diodes per light, Fix 3/4" Hole; Designed at 12 DC Volts; Sealed Light, 3 Wires Setup, High Low Function;

3/4" red led marker lights 3 wres: Red Mini 3/4" Stop Turn Tail Lights 3 LED with Rubber Grommets,very bright for it's size. Dual brightness. install with a rubber mounting grommet and requires a cutout hole of 3/4" diameter. These 3/4" led lights come with 3 wires (black wire is ground, white wire is tail light/marker light/clearance light/running light and red wire is for stop and turn functions). This light is DOT approved as your only tail light or turn signal;

Can be used as an aux lighting to your existing brake light, but not approved as a brake light.