Best Cdm Gear in 2026

PURPOSE – The MTRS20 with included 3 slot rail is the latest offering in the MT series of clamps for lights with built in attachment points

COMPATIBILITY – fits in the small space of the Mossberg 590 SHOCKWAVE 20 Gauge

EASY INSTALLATION - This mount can be positioned 2 ways, left, or right, and provides a solid "lock up" around the magazine tube that stays in place when you remove the barrel.

PURPOSE – The MTRS with included 3 slot rail is the latest offering in the MT series of clamps for lights with built in attachment points

COMPATIBILITY – fits in the small space of the Mossberg 590 SHOCKWAVE 12 Gauge

EASY INSTALLATION - This mount can be positioned 2 ways, left, or right, and provides a solid "lock up" around the magazine tube that stays in place when you remove the barrel

Mounting rings are pushed forward 2" for better eye relief

Designed for mil-spec upper receivers with 1913 Picatinny rail

6061 T6 extruded aluminum construction

Rear ring is pushed forward 1" for better eye relief

Designed for mil-spec upper receivers with 1913 Picatinny rail

6061 T6 extruded aluminum construction

Use this cantilever mount for mounting 30 mm telescopic sights.

The 2-inch offset of this cantilever mount positions the scope in a forward location, allowing the correct eye relief and head placement.

The cantilever ring mount positions the center of the riflescope tube at a height of 1.59 inches (40.39 mm) from the base. Weighs 6.7 ounces

UTG Super slim Picatinny riser mount, 0.5" saddle height, 3 slots, 1.57" in length

A fresh new look precision CNC Machined from 6061-T6 aircraft grade aluminum and finished in a matte black anodize

Distinctive scalloped Picatinny slots for snag free accessory mounting

UTG Super slim Picatinny riser mount, 0.83" saddle height, 3 slots, 1.57" in length

A fresh new look precision CNC Machined from aircraft grade aluminum and finished in a matte black hard coat anodize

Distinctive scalloped Picatinny slots for snag free accessory mounting

45° ANGLED MOUNT; Mounts to standard picatinny / 1913 / weaver rails

Angled mount provides FAST TRANSITION TO BACKUP OPTIC

IDEAL FOR MOUNTING LIGHTS / LASERS without blocking optical sight

Machined from domestic 6061 T6 extruded Aluminum, Matte Black finish only

Center spread - 3.825", overall length of mount - 6.670", Mauser 98 scope mount does not fit the 3000 L

Picatinny cross slots run the full length of the rail; center channel reduces overall mass of mount

Vortex Pro 30mm cantilever ring mount provides the correct height and forward placement for proper scope mounting

The cantilever ring mount positions the center of the riflescope tube at a height of 1.435” (36.45mm) from the base.

Made with pride in the USA

Use this cantilever mount for mounting 30mm tubes.

These extended cantilevers are designed for mounting scopes with a forward location, providing correct eye relief and head placement.

The cantilever ring mount positions the center of the riflescope tube at a height of 1.574” (40mm) from the base.

Model #177095 - Mark scope mount in size 34mm in Matte finish

For receivers with Mil-Spec 1913 Picatinny rails

Rear ring pushed 1" forward for better eye relief

6061 T6 extruded aluminum + anodized black finish

Dual ring scope mount available for both standard 1 inch and standard 30mm tube rifle scopes

Slim profile design offers the weight of lightweight scope rings with the added rigidity and convenience of a one piece mount

Mounts to any flat top Picatinny rail equipped rifle

Dual ring scope mount available for both standard 1 inch and standard 30mm tube rifle scopes

Slim profile design offers the weight of lightweight scope rings with the added rigidity and convenience of a one piece mount

Mounts to any flat top Picatinny rail equipped rifle

Compatible with most 9mm - 11mm, flat or rounded, airgun/shotgun dovetail rails

Recoil resistant Stop pin aids in additional zero retention against bidirectional recoil force typical of spring Operated airguns

Precision Machined from aircraft grade aluminum and finished in a matte black hard coat anodize

Dual ring scope mount for mounting standard 1 inch tube rifle scopes

Mounts to any flat top Picatinny rail equipped rifle

2 inches of forward extension allows extra flexibility for optimum eye relief and shooting position

Simplest, most effective way to mount any FastFire sight on a rifle

Allows the FastFire to mount at the optimum height, so the red dot can co-witness with flip-up sights

Fits Weaver or Picatinny-style base

Dual ring scope mount available for both standard 1 inch and standard 30mm tube rifle scopes

Slim profile design offers the weight of lightweight scope rings with the added rigidity and convenience of a one piece mount

Mounts to any flat top Picatinny rail equipped rifle

This quick-release cantilever mount is designed for mounting telescopic sights with 30mm tubes onto a flattop style rifle.

The offset of this cantilever mount positions the scope in a forward location, providing correct eye relief and head placement when used on your rifle.

This mount positions the center of the riflescope tube at a height of 1.45 inches (37 mm) from the top surface of the Picatinny base.

Mount for 407C, 507C, 508T Models

0.80 inches in height, measured from the center of the rifle scope tube to the bottom plane of the Picatinny rail mount

Monstrum Precision Scope Rings are precision crafted to a given height specification to match your particular rifle setup and preferred cheek weld

1 inch diameter rings for mounting standard 1 inch rifle scope tubes

Provides extra rail room for rear Back Up Iron Sights (BUIS) when using the StrikeFire red dot along with the VMX-3T magnifier.

The cantilever ring will move the StrikeFire forward about one inch.

Provides lower 1/3 co-witness mounting height of 40 mm.

1.35 inches in height, measured from the center of the rifle scope tube to the bottom plane of the Picatinny rail mount

Monstrum Precision Scope Rings are precision crafted to a given height specification to match your particular rifle setup and preferred cheek weld

1 inch diameter rings for mounting standard 1 inch rifle scope tubes

Compatible with Glock vortex venom viper burris fastfire ade *NOT FIT Counterfeit sights

Ultra Low Profile and lightweight, Easy to install.One Piece Design for a Secure Zero Hold.

30MOA design, Solved some red dots don't have enough elevation adjustment to put the sight down on pistol mount.

Low profile riser mount for red dots, scopes, and optics, allows for sight clearance over front sights

0.5 inch of rise, Picatinny rail mount, will accommodate Picatinny or Weaver standard red dots and optics

Attaches and detaches quickly and easily via integrated quick release mechanism

Double scope ring mount for Picatinny/ Weaver Rail (21mm).

Design in hollowed-out configuration between the ring and the bottom of the base, to release heavy duty when clamping your scope.

Built-in tape inside per rings to prevent from marring the scope, also prevent sliding and holding postion accurately.

STRONG DURABLE MOUNT - The Scalarworks LEAP Red Dot Mount for the Trijicon MRO is one of the most rock-solid quick-detach red dot mounts on the market; the re-designed clamp has discreet hardened steel pins and a stopper to indicate when it's sufficiently open to clear a Picatinny rail

7075-T6 ALUMINIUM CONSTRUCTION - LEAP red dot mounts are machined from 7075-T6 Aluminium and use 4140H steel hardware for absolute rigidity that results in a near seamless integration between your rifle and optic

CLICKDRIVE MECHANISM - The ClickDrive mechanism is also intuitive, self-adjusting, and completely recoil proof; thanks to the ClickDrive mechanism and the mount's absolute rigidity, LEAP mounts are guaranteed to hold AND return to zero

Proudly Designed And Made In Usa, Precision Machined From Aircraft Grade Aluminum Alloy With Hard Anodizing With Matte Black Finish

Unique Contoured Bottom Designed To Fits On Ruger 10/22 Pre-Drilled And Tapped Rifle Receiver

4.67 Inch Overall Length With 11 Picatinny Rail Slots For Optimal Placement Of Scope, Dot Sight Or Iron Sight, And Flexible Eye Relief Adjustment

Product 1: This quick-release cantilever mount is designed for mounting telescopic sights with 30mm tubes onto a flattop style rifle.

Product 1: The offset of this cantilever mount positions the scope in a forward location, providing correct eye relief and head placement when used on your rifle.

Product 1: This mount positions the center of the riflescope tube at a height of 1.45 inches (37 mm) from the top surface of the Picatinny base.