Best Hppamz in 2026

HPPAMZ 1615783102 Temperature Switch Sensor for Screw Air Compressor Replacement 1615-7831-02

This Temperature Switch is A Replacement And Is Not Manufactured or Sold By Atlas Copco.

✓ EFFORTLESS COOLING SETUP: Simply place the probe, plug-in the thermostat controller, and use the large 3-button interface to choose your desired temperature setting. Digital display supports units in both Fahrenheit and Celsius. Note: the controller is designed to have a 2-3 degree buffering zone before powering on again after reaching set temperature.

✓ EASE OF MIND: Handy LED cooling and power indicator lights allow you to see the controller’s status even in total darkness. Controller features a convenient hanging tab, and a bright, easy-to-read display inside a tough plastic housing.

✓ RUGGED CONSTRUCTION: The cord for the temperature probe and grounded 3-prong plug measure an extended 6-feet in length, designed to suit almost any application you can imagine.

Connector type: SPST, 2 terminal pin on/off. Power: 15A 250VAC/20A 125VAC

Material: Plastic and metal. Solid connection switch with waterproof rubber cap, more convenient to operate. Delicate appearance with strong construction. Look chic and high-end on your equipment

Mechanical life: More than 50.000 cycles. Electrical life: More than 10, 000 cycles

Materials:UL approved Nylon PA66(Flammability UL 94V-2) for A.C.F parts EPDM rubber for B.D parts

Thick Washer:Each cable gland Connector comes with a high quality rubber washer to ensure it remains watertight to the maximum.

Security Card Slot:Unique card slot design events cable gland connectors will cause accidents due to the reversal and loosening of nuts when used in vibration environment for a long time. We will ensure your safety in the detail design of products. Satisfying click when tightening the cap down so you know its secure.

Type: K Type; Measuring Range: 32~1112°F (0~600°C)

Probe Material:304 Stainless steel; Terminal: 2 Insulated forks; Thread: 2 Meters

Probe size：6mmx100mm/0.23“x3.9“（D * L），Thread ：NPT 1/2"

Temperature Probe for Camp Chef Pellet Grill; RTD Probe for Camp Chef Dlx Series, PG 22-24, PG24MZG, Woodwind, PG24-44, etc

7"(18cm) Internal Grill Sensor Probe; 47"(120cm) Heat Woven Wires

GREAT Camp Chef Rtd replacement probe and/or additional probe; Digital control meat probe capability, Maintains more consistent temperatures

Fits all Traeger Wood Pellet Grills (EXCEPT PTG)

Maintains more consistent temperatures

RTD probe for Digital Thermostat

GM-recommended replacement part for your GM vehicle’s original factory component

Offering the quality, reliability, and durability of GM OE

Manufactured to GM OE specification for fit, form, and function

Wide Measuring Range: DROK digital thermometer probe is able to tolerate the widest measuring range (-25°c to 125°c (-13℉ to 257℉)).

High-quality Stainless Steel Probe: This temperature test probes has 5*25mm stainless steel housing, which is waterproof, moisture-proof and anti-rust.

Advanced Technology: DROK smart temp probe adopts sensitive and reliable NTC thermistor and connected by PVC wire, 3 meter lead length (9.8ft), available for remote temperate measuring and controlling.

Advanced Technology: DROK smart sensors cable adopts sensitive and reliable NTC thermistor and connected by PVC wire, 1 meter lead length (3.28ft), available for remote temperate measuring and controlling.

Wide Measuring Range: Our temperature probe is able to tolerate the widest measuring range (-25°c to 125°c (-13℉ to 257℉)).

Stainless Steel Probe: This temperature sensor for car has 5*25mm stainless steel housing, which is waterproof, moisture-proof and anti-rust.

Compatible Vehicles: BMW 5 Series F07 F10 F11, 6 Series F06 F12 F13, 7 Series F01 F02 F03, X5 Series F15 F85, X6 Series F16 F86.Fit for the front console climate control panel and rear seats climate control panel.

There are 4 packs of accessories in the package, including a knob cover with ‘AUTO’, a knob cover without‘AUTO’,a chromed ring and a rubber ring. A completed knob consists of a knob cover,a chromed ring and a rubber ring.You may combine 4 pieces into button with ‘Auto’ or button without ‘Auto’ according to the configuration of your car.

High-quality material: The upgraded air conditioning knob is made of ABS+PC material, which is durable, anti-aging and Scratch-resistant.

Grounded thermocouple thermistor . The K thermocouple temperature sensor is waterproof . This is a water tight sensor probe

The K type temperature sensor probe temperature range is 0~500℃ ( 932 Fahrenheit ) . Accuracy : 0.2 .

This K temperature sensor is rustproof , it is made from stainless steel . Water proof Insulation Lead

High Temperature K-type Thermocouple with ceramic tube insulation

Continuous use up to 2372 °F or 1300 °C, NOTE: Thermometer displays only up to 1999 degreeF, but 1300 °C

Total length 8.5 inch, insulated length 6.5 inch

This Kit contains with 3pcs of digital sensor module, which can be independently enabled / disabled, which can measure not only the temperature humidity, but also the pressure.

The BMP280 sensor is great for all sorts of weather sensing and can even be used in both I2C and SPI! For simple easy wiring, go with I2C. If you want to connect a bunch of sensors without worrying about I2C address collisions, go with SPI.

Our BMP280 Sensor is the best low-cost, precision sensing solution for measuring barometric pressure with ±1 hPa absolute accuraccy, and temperature with ±1.0°C accuracy. Because pressure changes with altitude, and the pressure measurements are good, you can also use it as an altimeter with ±1 meter accuracy.

5PCS ADI TMP36GZ temperature sensors,High accuracy solid state temperature sensor.

Voltage Input: 2.7V to 5.5V DC,Output range: 0.1V (-40°C) to 2.0V (150°C)

Temperature range: -40°C to 150°C / -40F to 302F 2°C accuracy

Temp measurement range：-40℃~100℃/-40℉~212℉

Temp display accuracy：0.1℃/℉(<100℃/℉)

Temp sensor cable Length: 2m(78.74in)

Type K Pipe Clamp Temperature Lead Probe

Operating temperature: -40°C to 200°C / 392°F

Clamp Jaw Opening: 1 3/8-Inch (6.5 cm) , Length of Cord: 40-Inch (102 cm)

You will get: the package comes with 30 pieces k type thermocouple temperature probe sensors in 3 meters long, the enough quantity and length to meet your daily need

Measurement range: the measure range of the temperature sensing line is -58 to 752 °F (-50 to 400 °C); And the probe sensor can effect in 5 second with the accuracy degree 0.025 or 0.075; The interface form is flat plug-in

Wide Applications: for general purpose temperature applications, the k type mini-connector is fastly response that is suitable for rapid measurement of air and gas, not suitable for liquid measurement; Allows forming and bending of the thermocouple, so you don't need to worry about the risk of cracking

Temperature controller monitoring instrument, show the measured temperature (red) and set temperature (blue) at the same time. Can be used for cooling/heating control. Operating Voltage: DC12V 200mA

Measurement Range: -50 to 110 Celsius (-58 to 230 F), the C/F button allows you to switch between Celsius and Fahrenheit temperatures

Clear Working State: the relay is closed when the light is on, and the relay is disconnected when the light is off. It has high temperature protection.

Product name: thermocouple Connector; Type: K Type ; Cable Length: 3 meter

Measurement range: -58 to 662°F (-50 to 350°C)

For general purpose temperature applications,Fast response time

2 Working modes: this digital LED temperature controller module has 2 working modes, heating mode (start temperature is lower than stop temperature) and cooling mode (start temperature is higher than stop temperature), range from -50°C to 110°C; The high temperature control accuracy reaches 0.1℃

Stable and reliable: the LED indicator light can display the current output status; The digital display tube can display the measured temperature, and the temperature measurement and control accuracy is high

Durable material: this XH-W3001 digital thermostat switch is made of ABS, one of the five major synthetic resins, which is non-toxic, strong impact resistance, heat and low temperature resistance

Not only the pressure and the temperature, this sensor can measure humidity.

Make sure to put SDO to high to get address 0x77. This will work with Adafruit BME280 library perfectly.

BME280 is a precision sensor, is soldered onto PCB. It uses both I2C and SPI (supports 3-, 4-wire SPI) interface.

K-type Thermocouple with high Quality Pointed Stainless Steel Sensor

K-type thermocouple wire with Standard Accuracy: +/- 2.2 °C or +/- .75%

5 ft (155 cm) long thermocouple cable with braided stainless steel cover, mini thermocouple plug made from chromel / alumel

Not only the pressure and the temperature, this sensor can measure humidity.

Make sure to put SDO to high to get address 0x77. This will work with Adafruit BME280 library perfectly.

BME280 is a precision sensor, is soldered onto PCB. It uses both I2C and SPI (supports 3-, 4-wire SPI) interface.

✅[Warranty] 365 days Warranty. With a Refund Guarantee and Free Replacement policy, you can buy with confidence.

✅[Application] Heating and Air Conditioning Control Panel for 2004 2005 2006 2007 2008 2009 2010 2011 2012 Chevrolet Colorado GMC Canyon with RPO Code C60 (Manual Air Conditioning) Heater & A/C Control.

✅[Application] Heating and Air Conditioning Control Panel for 2006 Isuzu i-280 with RPO Code C60 (Manual Air Conditioning) Heater & A/C Control; 2007 2008 Isuzu i-290 with RPO Code C60 (Manual Air Conditioning) Heater & A/C Control; 2006 Isuzu i-350 with RPO Code C60 (Manual Air Conditioning) Heater & A/C Control; 2007 2008 Isuzu i-370 with RPO Code C60 (Manual Air Conditioning) Heater & A/C Control.

Product Type: PRECISION MEASURING

Package length: 28.194 cm

Package width: 17.526 cm

►Product Name : Thermocouple Probe;Connector Type : K Type

► Operating Temperature: -40-480°C

► Temperature Range: 0 to 400C; Accuracy : 2.5%/0.75%

Fit for the K Series VTEC switch and the J Series Fan, Coolant Temperature and Intake Air Temperature sensors.

Fit for the Coolant Temperature Sensor on B/D/H/F Series Honda and Acura Engines, along with other connectors like the Fan, Knock Sensor and Intake Air Temperature Sensor.

Pigtail Wire Length: 12".

The pluggable DS18B20 temperature probe sensor is easy to plug and can be used in a variety of environments.

With pull-up resistor on board, the adapter module can be connected directly to most microcontrollers and it is widely used in temperature monitoring for fish tanks, equipment, machinery, greenhouses.

Widely applications: thermostatic controls, industrial systems, consumer products, thermometers, any thermally sensitive system, etc.