Best Raesung in 2026

ETCR5000 Three Phase Power Quality Analyzer is easy to use, large LCD screen display, high resolution, in English bilingual interface, features of anti vibration structure shell etc.

Functional diversity:test, capture and monitoring functions, record storage function, Alarm function, Screenshot function etc,Battery indicator: Battery symbol 5 grid display power, when the battery power is too low, prompt automatic shutdown after 1 minutes.

Operating temperature and humidity: -10℃～40℃;below 80%Rh; Storage temperature and humidity: -10℃～60℃;below 70%Rh.

ETCR2100A+ clamp ground earth resistance meter grounding and loop resistance measurement, more reliable quality.

Structural Feature：Clamp CT,and can measure the ground fault which can not be measured by traditional method.

Shifting：Automatic shifting.Auto Power-off：5 minutes after boot up.

n accordance with ISO 2372, used for periodic measurements, to detect out-of-balance, misalignment and other mechanical faults in rotating machines.

Can communicate with PC computer for statistics and printing by the optional cable and the software for RS232C interface.

Specially designed for easy on site vibration measurement of all rotating machinery for quality control, commissioning, and predictive maintenance purposes.

Surface Profile Gauge meets the standards of ASTMD-4417-B, IMOMSC.215(82), SANS5772, US Navy NSI 009-32, US Navy PPI-63101-000. Suitable for the laboratory and for use in harsh field conditions. Accurate, immediate and repeatable results.

The tungsten carbide tip will last for up to 20,000 readings and can then be easily replaced by the user in the field. Cost per test is significantly lower than other test methods.

The roughness tester Metric/Imperial Conversion and average calculation function.

94dB And 114dB Sound Calibrator At 1KHz.

Accurate And Simple To Use.

Fits 1inch And 1/2inch Microphones.

CL120 Clamp Meter measure AC current via the clamp, and AC/DC voltage, resistance and continuity via test leads

Meter has backlit LCD for ease of viewing in low light and is CAT III 600V, Class 2 Double Insulated

RT210 detects the most common wiring problems in standard and GFCI receptacles

Automatically measures volts ac and volts dc with precise digital resolution

Displays resistance to 1000Ω

Easy and accurate OpenJaw current measurement

Multi -Function T-RMS clampmeter that accurately measures linear or non-linear loads: can measure AC and DC current, AC and DC voltage, Low impedance, Continuity/Resistance/Capacitance, Temperature, Frequency, and Duty Cycle; Easy to use and operate.

Non-Contact Voltage (NCV) Detection: check if a conductor being measured carries a voltage higher than 90V AC without touching any wires; NCV sensor is at the tip of the clamp, press NCV to display EF, bring the sensor close to the conductor under test

Features: LCD display, low battery detection, overload protection, auto power off after 15 minutes, flashlight. Meets IEC safety standard 61010-1 with the CAT III 600V overvoltage protection standard

N.O. Universal Outputs: 2.5A @ 120 VAC/240VAC; In 240V circuit, only one 120V hot line is connected.

Self-powered, no external power supply required

Accurate & Dependable: Offers a sensing range of 1 to 50 amps and universal, solid-state outputs; Accuracy: 1%

60A AC/DC Amp Clamp Probe

Use with most DMM

Zero/Calibration Function

Turns 120 VAC devices on when input current is sensed

UL 94-V0 rated for flammability safety

Item Package Dimension: 4.0" L x 4.0" W x 4.0" H

Two-color LED indicator senses alternating current

11" wire leads for remote indication

Self-powered for quick installation

💥【Convenient】-Compared with buying a delicate and expensive clamp meter,getting a clamp accessory for your DMM is much wiser.It provides you more freedom.the display will not constrain to where you gauge current,but anywhere you want,more friendly to aerial workers,guaranteeing your safety!

💥【Wide Range】-A clamp-on meter can extend the measurement range.AN-605A can be used to test AC/DC amp up to 600A.Note:The flow of electricity can only be measured in one direction at a time,or the currents in opposite directions will cancel each other out,causing wrong measurement results.

💥【Big Open Jaw】-Built with 45mm/1.77 inches large open jaw,it is very easy for you to clamp it on measured thick wire.

Accurate measurements down to 1 mA (.001A) - 80A maximum reading DC/AC

Larger clamp size of .75" (19 millimeter) and improved zero drift stability - Electronic Specialties enlarged the clamp opening as much as possible while still maintaining 1 mA resolution

Minimum/Maximum and Peak Minimum/Maximum functions, Data Hold, Relative Zero - Full DMM built-in

Current sensor chip: ACS712ELC-30A（Note: there are 3 specifications of the product 5A/20A/30A, Pls choose them accroding to your needs.）

Pin 5V power supply; on-board power indicator; Measuring range: ±30 amps, corresponding Analog output:66mV/A.

When there is no the detection current through, the output voltage is VCC/2

Analog Current Meter Module. Transformer can only sense AC

This electricity sensor is based on TA12-100 current transformer, which can transform AC signals of large current into small amplitude signals.

3-wire electronic block interface, input 5V - GND. S pin is the output analog voltage value.

Load Maximum Current: +/-5Amp, +/-20Amp and +/-30Amp selectable. Load Frequency Bandwidth: DC ~ 80 kHz. Minimum Isolation Voltage: 2.1 kV(RMS). Operating Voltage: Regulated 5VDC, or 8 ~ 35VDC. Operating Current: 20mA(max).

The item provides economical and precise solutions for AC or DC current sensing in industrial, commercial, and communications systems. Typical applications include motor control, load detection and management, switched-mode power supplies, and overcurrent fault protection.

Output voltage proportional to AC or DC currents.

Load Maximum Current: +/-5Amp, +/-20Amp and +/-30Amp selectable. Load Frequency Bandwidth: DC ~ 80 kHz. Minimum Isolation Voltage: 2.1 kV(RMS). Operating Voltage: Regulated 5VDC, or 8 ~ 35VDC. Operating Current: 20mA(max).

The item provides economical and precise solutions for AC or DC current sensing in industrial, commercial, and communications systems. Typical applications include motor control, load detection and management, switched-mode power supplies, and overcurrent fault protection.

Output voltage proportional to AC or DC currents.

Load Maximum Current: +/-5Amp, +/-20Amp and +/-30Amp selectable. Load Frequency Bandwidth: DC ~ 80 kHz. Minimum Isolation Voltage: 2.1 kV(RMS). Operating Voltage: Regulated 5VDC, or 8 ~ 35VDC. Operating Current: 20mA(max).

The item provides economical and precise solutions for AC or DC current sensing in industrial, commercial, and communications systems. Typical applications include motor control, load detection and management, switched-mode power supplies, and overcurrent fault protection.

Output voltage proportional to AC or DC currents.

ACS723 AC DC current sensor with OPA344 OpAmp

Hall Effect

Measure both AC and DC currents from 10mA up to 5A

Input:0-10A,20A,50A AC(With 3 input ranges meanwhile,selected with stick jumper)

Load Capacity:2 times current continuous

Enclosure Rating:UL,94 V-O flammability rated,ABS plastic housing

ETCR5000 Three Phase Power Quality Analyzer is easy to use, large LCD screen display, high resolution, in English bilingual interface, features of anti vibration structure shell etc.

Functional diversity:test, capture and monitoring functions, record storage function, Alarm function, Screenshot function etc,Battery indicator: Battery symbol 5 grid display power, when the battery power is too low, prompt automatic shutdown after 1 minutes.

Operating temperature and humidity: -10℃～40℃;below 80%Rh; Storage temperature and humidity: -10℃～60℃;below 70%Rh.

Stable：D05 220V input voltage, 0.3-50A measurement range, it has stable performance.

Safe protection:Current overload protection, monitors whether the equipment is working normally, and there is no current to the switch signal.

Function:Used for the measurement and display of a single current in the electrical circuit, and can be equipped with a relay alarm output.

High accuracy: Mutual inductance current monitoring has high current detection accuracy and safe isolation of input and output.

Self-powered: there is no external power supply required.

Easy to install: There is no need to connect DC into the circuit when measuring.

Input:0-10A,20A,50A AC(With 3 input ranges meanwhile,selected with stick jumper)

Load Capacity:2 times current continuous

Enclosure Rating:UL,94 V-O flammability rated,ABS plastic housing

Input:0-10A,20A,50A AC(With 3 input ranges meanwhile,selected with stick jumper)

Load Capacity:2 times current continuous

Enclosure Rating:UL,94 V-O flammability rated,ABS plastic housing

Input:0-100A DC

Output:4-20mA DC

Power Supply:24V DC +/-15%(If you need other power such as 12V,contact us)

Load Maximum Current: +/-5Amp, +/-20Amp and +/-30Amp selectable. Panel Mount Version.

The item provides economical and precise solutions for AC or DC current sensing in industrial, commercial, and communications systems. Typical applications include motor control, load detection and management, switched-mode power supplies, and overcurrent fault protection. The device is not intended for automotive applications.

Output voltage proportional to AC or DC currents.

Load Maximum Current: +/-5Amp, +/-20Amp and +/-30Amp selectable. Panel Mount Version.

The item provides economical and precise solutions for AC or DC current sensing in industrial, commercial, and communications systems. Typical applications include motor control, load detection and management, switched-mode power supplies, and overcurrent fault protection. The device is not intended for automotive applications.

Output voltage proportional to AC or DC currents.

Measuring Range : 0~600A

Clamp Caliber : 30mm

Signal Output : 1 mV / 1A