Best Medca Mono Amplifiers in 2026

The Punch P500X1bd is a full chassis (2.38” x 7.76” x 11.03”) mono amplifier optimized for subwoofers only, capable of 500 Watts into a 1-Ohm load

Class-BD technology produces bass more efficiently over traditional amps (RMS Power Output: 150 Watts x 1 @ 4-Ohm OR 300 Watts x 1 @ 2-Ohm OR 500 Watts x 1 @ 1-Ohm)

RCA inputs can accept both Hi and Low level audio signals without the need of a signal converter

Competition Grade SPL Class D Mono black MOSFET Car Power Amplifier

Peak Power at 1 Ohm: 7, 400 Watts | RMS Power at 1 Ohm: 4, 500 Watts

Stable at 1 Ohm, Frequency Response: 15Hz - 270Hz

Includes: Amplifier. Bass Remote. Birth sheet with tested power. Owner’s manual. Mounting Screws. Warranty.

Rockville dB13 3000 Watt Peak/750w Dyno-Certified RMS Mono 2 Ohm Amplifier Car Amp. Dyno Certified RMS Power Ratings: (Certified Dyno Test / Less than 1 % THD) (Use these ratings when comparing with top brands such as Kicker, Rockford Fosgate, etc). - 2 Ohm: 750 Watts x 1 Channel <1% THD+N. - 4 Ohm: 450 Watts x 1 Channel <1% THD+N.

Peak: (Use these ratings when comparing with the top budget brands such as Boss, Power Acoustik, etc). - 2 Ohm: 3000 Watts x 1 Channel. - 4 Ohm: 1800 Watts x 1 Channel. High-Speed MOSFET Power Supply. Optical Coupler Class “D” Technology. Fully Adjustable 12dB / Octave Crossover with Differential Circuitry. Low Pass Filter: 50Hz - 250Hz. Subsonic Filter: 15Hz - 55Hz. Phase Control Switch.

Wiring Installation Kit includes: 30 ft. speaker wire, 20 ft. 8 ga red power cable, 16 ft. 18 ga blue turn-on wire, 3 ft. 8 ga Black ground cable, competition quality fuse holder with agu fuse

WIRING INSTALLATION KIT CONTINUED: 10 5/16" and 1/4" Ring Terminals, 6 ft. Split Loom Tubing, 3 Rubber Grommets, 20 4" Wire Ties, 20 ft. High Performance blue RCA (TRCA) Interconnect

Amplifier power: 1500 watts Max X 1 @2-ohms, 750 watts Max X 1 @4-ohms

2500 W MAX Power @ 2 Ohm x 1 Channel

1250 W MAX Power @ 4 Ohm x 1 Channel

High and Low Level Inputs

RMS Power Rating: 4 ohms: 500 watts x 1 chan. / 2 ohms: 800 watts x 1 chan. / 1 ohm: 1200 watts x 1 chan.

Pulse Width Modulated MOSFET power supply Wired remote bass level control included

Preamp RCA outputs to daisy chain multiple amps 3-way protection circuitry (thermal, overload, and speaker short protection)

1500 W MAX Power @ 2 Ohm x 1 Channel

750 W MAX Power @ 4 Ohm x 1 Channel

High and Low Level Inputs

Maximum power @ 14. 4VDC - 2 x 50W RMS (stereo 2 ohms)

Maximum power consumption: 7. 6 amps (musical: 3. 8 amps)

Channels: 2, topology: class-d

MD 12000.1 - 0.5 ohm amplifier is developed with the highest technology and performance for automotive sound systems, in white color, to make your system more sophisticated, It is mono, with a single channel with a maximum power of 12.000 Watts RMS.

It is a FULL RANGE amplifier, playing all frequencies in the right measure for you, Operation class Class D, Number of Channels 01, Maximum power @ 12.6 VDC - 0.5 OHM: 12,000W RMS @ 12.6 VDC - 1 OHM: 7,200W RMS

Input Sensitivity 220mV, Signal to Noise Ratio >95dB, Frequency Response 10 Hz ~5 kHz (-3dB), Crossover high pass (HPF) 10 Hz ~90 Hz (-12dB/8th) Variable, Crossover low pass (LPF) 90 Hz ~5 kHz (-12dB/8th) Variable, Bass Boost Freq.: 35 Hz ~55 Hz

1000-WATT POWER: The Crunch PowerDriveX Car Stero Amplifier boasts 1000 Watts power; 2 x 250 watts at 4 ohms, 2 x 500 watts at 2 ohms, 1 x 1000 watts at 4 ohms bridged

2 CHANNEL AMP: 2 Channel amplifier with Low noise pre amplifier with Rugged MOSFET pulse width modulation power supply; Series A/B car amplifier; Maximum low voltage signal from the source unit comes into the amplifier circuit with minimal distortion

INPUTS/OUTPUTS: Low level RCA inputs and outputs; Audio inputs: Unbalanced inputs (RCA) Audio outputs: Line output (RCA)

True RMS Power Rating: 4 ohms: 450 watts x 1 chan. ❘ 2 ohms: 750 watts x 1 chan.

Variable Bass Boost (0 to +18 dB bass boost at 50 Hz)

Variable low-pass filter (50-250 Hz, 24 dB/octave)

Class-D Mono-block Subwoofer Amplifier, 1200 Watts Max Power, RMS 600 Watts x 1@2Ohm; RMS 350 Watts x 1@4Ohm.

Featuring a high-speed MOSFET power supply, premium grade internal components, as well as 4-way protection circuitry, the amplifier will safely operate at the highest levels of performance for hours on end. Highly efficient heatsinks keep the amplifier cool with a sophisticated new look.

Recoil mono amplifiers come with bass remote control. Use it to customize your bass on the fly with just a turn of a knob.

Input Level: 0.2V ~ 16V

Frequency Response: 10 ~ 250 Hz

Watts: 500W

This listing contains: (1) NA1600.1AB 1600 Watt Max Monoblock Class A/B Amplifier (1) Remote Bass Knob with Connector cable (1) Operations Manual (1) Mounting Hardware Set

1 x 800W @ 4 Ohms 1 x 1600W @ 2 Ohms

Features: Nickel Plated Terminals Extruded Aluminum Heat Sink Low Level Input High Level Input Low Level Output Remote Bass Knob Included Mil Spec Double-Sided Glass Epoxy Circuit Board 4-Way Protection Circuitry: Thermal, Short Circuit, Overload and DC Offset Variable Low-Pass Crossover: 50Hz - 250Hz Variable Input Sensitivity: 200mV - 6V 45Hz Bass Boost: 0 - 12dB ATC Fuse: 30 Amp x 2

Remote IN: 7 ÷ 15 VDC - 1mA

Remote OUT: 12 VDC - 50mA

Fuse (Strip type): 100A

Package Includes: (1) MB Quart FA2-400.4 400 Watt 4-Channel Car Stereo Amplifier Class Q1 Amp, (1) Rockville RWK42 4 Gauge 4 Chan Car Amp Wiring Installation Wire Kit (2) RCA's

Features of FA2-400.4: Low Noise Preamplifier Circuit: Q-Stasis Pre Amplifier Stage: Maximum low voltage signal from the source unit comes into the amplifier circuit with minimal distortion. RCA Inputs: Nickel Plated: High temperature impact resistant nickel-plated RCA inputs that allow for secure connections and is erosion resistant. High Level Inputs: DC SIGNAL SENSE: The DC SIGNAL SENSE switch will allow the amp to turn on when a signal is received on the RCA inputs,

so an amplifier remote turn on wire is not needed to turn on the amplifier. This feature can also be turned off. Operation Mode: 4 channel operation mode allows either stereo or mono bridged operation. Crossover Type: Variable electronic crossovers allow for complete control of the sound. Electronic Equalizer: Control of amplifier output with on-board electronic crossover to tailor specific frequencies to speakers and subwoofers. Check specifications for specific frequencies for this amplifier