Best Medca Mono Amplifiers in 2026

The R2-500X1 full-range class-D mono amplifier (1.9" x 6.8" x 8.5") is packed with features and performance to deliver power and bass on demand with 500 Watts of RMS power

Class D technology makes this amp extremely efficient by reducing demand on the vehicles electrical system (RMS Power: 300 Watts x 1 @ 4Ω OR 500 Watts x 1 @ 2Ω)

Featuring C.L.E.A.N. circuitry to help you adjust your gain settings, a P.O.W.E.R. Supply that generates more power as voltage increases, and integrated Punch EQ that corrects for acoustic deficiencies while delivering up to 3X the bass

The BXX1200.1D is a 1200 watt mono amplifier featuring Super Class D technology with an NGSD digital chip to provide you with an extremely efficient, low temperature, high amplification system that others only dream about.

The rock solid Ultra-Fi MOSFET outputs are selected for both balance and output power. This keeps power smooth even during demanding peak in the music.

The amplifiers protection condition is also shown by blue illumination for normal operation and red for a short being present and requires the attention of an installer.

HIGH-POWERED CAR AMPLIFIER: Enjoy serious sound beyond standard car speakers with our 3.5-inch class-D amplifier. This car amp has a max power output of 1,800 W and an input sensitivity of 0.2–5 V, so your car’s stereo can reach your desired volume.

PROFESSIONAL SOUNDS: Our car-audio amplifier’s total harmonic distortion (THD) is less than 0.15% for clearer audio. This loud amp also has a signal noise ratio of 70 dB, a frequency response of 8 Hz–180 kHz, and a crossover range of 5 Hz–50 kHz

ADJUSTABLE AMP: With a full MOSFET circuit design and simple bridging operation, this big amp is also phase, subsonic, level, and low-pass-filter adjustable. The included bass remote and knob aid with quick and easy control of the bass level.

Power - 2000 watts Max X 1 @2-ohms, 1000 watts Max X 1 @4-ohms

Class A/B topology - Class ‘A’ amplifiers have enormous amount of current flowing through its output transistors with no audio signal. Class ‘B’ amplifiers have no current flowing through its outputs with no audio signal

Low/high level inputs - a low level (RCA) input is measured in voltages. A high level (+/- wire) input is measured in wattages. Both essentially carry signal from your receiver to your amplifier to your speakers

VERY GREAT DEAL: A monoblock amplifier is typically expensive, but the Lanzar mono-block amplifier is inexpensive while still providing all of the features, such as reducing crosstalk between channels.

EASY SOUND CUSTOMIZATION: This high-powered Power Amplifier represents cutting-edge technology at its best. The RCA connectors and speaker screw-down terminals ensure a secure connection between amplifier and speakers, allowing distortion-free sound

SPECIALIZED AUDIO EVOLUTION: This amplifier car audio has excellent frequency response rates and a crossover network that puts it in a class of its own. With its cutting edge technology, the audio produced is very high quality

COMPACT DESIGN: Digital class D Brazilian technology allows this amplifier to have a small footprint by integrating a high-speed mosfet power supply with top of line transistors to ensure performance in a small heat sink without compromising performance. Dimensions: 3.93″ depth x 5.02″ width x 2″ height

POWER: This amplifier is designed to run your stereo system with the power it needs to perform! 500 Watts maximum dynamic RMS power output of 4x 125 Watts at 2 Ohms per channel. Its high efficiency rate of 87% provides more power with less battery consumption.

BRIDGEABLE: Double the power output to your speakers by bridging two channels. Minimum impedance of 4 Ohms per bridged channel at output power of 2 x 225 Watts RMS

Features:. . Rockville KRYPTON M3 4000 Watt Peak and 1000w RMS Class D 1 Ohm Stable Mono Amplifier With Voltage Display. Dyno Certified RMS Power Ratings: (Certified Dyno Test / Less than 1 % THD) (Use these ratings when comparing with top brands such as Kicker, Rockford Fosgate, etc).

1 Ohm: 1000 Watts x 1 Channel <1% THD+N (71% efficient). 2 Ohm: 700 Watts x 1 Channel <1% THD+N (79% efficient). 4 Ohm: 400 Watts x 1 Channel <1% THD+N (84.5% efficient). Peak: (Use these ratings when comparing with great brands such as Boss, Power Acoustik, etc).

1 Ohm:4000 Watts x 1 Channel. 2 Ohm:2800 Watts x 1 Channel. 4 Ohm:1600 Watts x 1 Channel. Digital Voltage Display on Amp (Accurate within 0.15V). Power/Protect/Clip LED Indicators on the front panel. Power/Protect/Clip LED Indicators on Remote control.

📢 PEAK POWER: 1000 Watts

📢 RMS POWER: 【4 ohms: 180W x 1 chan.】【2 ohms: 320W x 1 chan.】【1 ohm: 500W x 1 chan.】

📢 COMPACT: Cutting edge Micro Class D technology allows amplifier to be extremely compact. Dimensions: 6.8"L x 3.3"W x 1.5"H

Power: 2500 watts max X 1 @1-ohm, 1250 watts max X 1 @2-ohms, 625 watts max X 1 @4-Ohms

Class D: power loss is significantly reduced making the amplifier highly efficient. Excess energy is stored until it’s needed instead of being converted into heat. Reduction in size/weight, reduced power waste, smaller heat sink, compact circuitry

1 ohm stable: able to continuously power loads of 1 ohm without encountering difficulties such as overheating. Typically made to power up subwoofers that demand the heavier power load requirements to be able to perform the way they were made to

MD 12000.1 - 0.5 ohm amplifier is developed with the highest technology and performance for automotive sound systems, in white color, to make your system more sophisticated, It is mono, with a single channel with a maximum power of 12.000 Watts RMS.

It is a FULL RANGE amplifier, playing all frequencies in the right measure for you, Operation class Class D, Number of Channels 01, Maximum power @ 12.6 VDC - 0.5 OHM: 12,000W RMS @ 12.6 VDC - 1 OHM: 7,200W RMS

Input Sensitivity 220mV, Signal to Noise Ratio >95dB, Frequency Response 10 Hz ~5 kHz (-3dB), Crossover high pass (HPF) 10 Hz ~90 Hz (-12dB/8th) Variable, Crossover low pass (LPF) 90 Hz ~5 kHz (-12dB/8th) Variable, Bass Boost Freq.: 35 Hz ~55 Hz

1000-WATT POWER: The Crunch PowerDriveX Car Stero Amplifier boasts 1000 Watts power; 2 x 250 watts at 4 ohms, 2 x 500 watts at 2 ohms, 1 x 1000 watts at 4 ohms bridged

2 CHANNEL AMP: 2 Channel amplifier with Low noise pre amplifier with Rugged MOSFET pulse width modulation power supply; Series A/B car amplifier; Maximum low voltage signal from the source unit comes into the amplifier circuit with minimal distortion

INPUTS/OUTPUTS: Low level RCA inputs and outputs; Audio inputs: Unbalanced inputs (RCA) Audio outputs: Line output (RCA)

Competition Grade Class D Monoblock Amplifier

Peak Power at 1 Ohm: 11,000 Watts | RMS Power at: 5,480 Watts.

Stable at 1 Ohm, Frequency Response: 15 Hz to 250 Hz

Power - 3000 Watts Max x 1 @1-Ohm, 1500 Watts Max x 1 @2-Ohms, 750 Watts Max x 1 @4-Ohms, 6000 Watts Max x 1 @2-Ohms Strapped / Bridged

Class D - Power loss is significantly reduced making the amplifier highly efficient. Excess energy is stored until it’s needed instead of being converted into heat. Reduction in size/weight, reduced power waste, smaller heat sink, compact circuitry

1 Ohm Stable - Able to continuously power loads of 1 Ohm without encountering difficulties such as overheating. Typically made to power up subwoofers that demand the heavier power load requirements to be able to perform the way they were made to

HIGH PERFORMANCE CAR AUDIO AMPLIFIER | The best competition amplifiers for cars in the market! This 12v car amplifier features: 2000 Watts x 1 RMS @ 1 Ohm / 4000 Watts MAX, Freq: 10Hz - 220Hz, 0~12dB, Built-In OEM Line Converter, High Power in Extremely Small Heat Sink, Bass Boost 0~12dB, and Ground Loop Isolator. Our monoblock amplifier for car provides real punch for your car stereos and car subwoofers!

PRODUCES POWERFUL, CLEAN, FULL SOUND | Don't settle for weak sounding and underpowered car subwoofer amplifier. Your car amplifier package and car subwoofer set aren't complete without our monoblock Massive amplifier. Our car audio subwoofer amplifier features: Built-in OEM line converters with RCA inputs that can take a high level speaker signal at up to 10 Volts directly in. DC 5V - 15V Operating Voltage.

QUALITY TESTED AND GUARANTEED TO ALWAYS REACH ITS FULL POWER | Hits its full power all the time! That is our guarantee! You don't need to set the gain to low to avoid distortion. It works great and provides high power with low efficiency. Also, by sensing the DC offset of a factory radio it can activate the ATO (Auto Turn On) feature and Next Generation Advanced 5 Way Protection Circuitry.

Dimensions (W x H x D): 12-5/8 inch x 2 inch x 6-5/8 inch

Operating Voltage: 14.4V（11-16V allowable）

Current Consumption: 60[A]

Package Includes: (1) Kicker 46CXA4001T CXA400.1 400 Watt Mono Class D Car Audio Amplifier Amp. (1) Kicker 46CXARCT Remote Control For 46CX 45CXA Series Amplifiers Amps

Features of 46CXA4001T: KICKER 46CXA4001T CXA400.1 400 Watt RMS Mono Class D Car Audio Amplifier Amp. Efficient Class-D amplifier. Three-second turn-on/off delay to eliminate unwanted interference. Variable 12dB crossovers provides control to dial in perfect sound. KickEQ 6dB variable bass boost for those additional low frequencies. 24dB subsonic filter for protection from potentially damaging frequencies.

FIT+ (Fail-safe Integration Technology-PLUS) means it works with nearly every radio. Accepts up to 40-volt input signal. Small footprint for easier installation. Compatible with CXARC (link to remote) Remote Bass Control. Vertical mounting hardware included for another unique look. Dimension (L x W x H): 12 inch x 9 inch x 4 inch. Weight: 5 lbs

Class-D Mono-block Subwoofer Amplifier, 1200 Watts Max Power, RMS 600 Watts x 1@2Ohm; RMS 350 Watts x 1@4Ohm.

Featuring a high-speed MOSFET power supply, premium grade internal components, as well as 4-way protection circuitry, the amplifier will safely operate at the highest levels of performance for hours on end. Highly efficient heatsinks keep the amplifier cool with a sophisticated new look.

Recoil mono amplifiers come with bass remote control. Use it to customize your bass on the fly with just a turn of a knob.

This listing contains: (1) V1200.5 2400 Watt 5 Channel Class A/B Amplifier (1) Remote Bass Knob with Connector cable

4 x 75W + 1 x 300W @ 4 Ohms 4 x 150W + 1 x 600W @ 2 Ohms 2 x 300W + 1 x 300W @ 4 Ohm N/A + 1 x 600 @ 2 Ohm

Features: Nickel Plated Terminals Low Level Inputs Remote Bass Knob Included Mil Spec Double-Sided Glass Epoxy FR Circuit Board 4-Way Protection Circuitry: Thermal, Short Circuit, Overload and DC Offset Variable Low-Pass Crossover: 50Hz - 250Hz Variable Input Sensitivity: 200mV - 6V Phase Control: 0 - 180 Degree 45Hz Bass Boost: 0 - 12dB S/N Ratio: > 85dB THD: 0.08%

Input Level: 0.2V ~ 16V

Frequency Response: 10 ~ 250 Hz

Watts: 500W

RMS Power - 1 ohm Mono: 2000W

RMS Power - 2 ohm Mono: 1000W

RMS Power - 4 ohm Mono: 500W

KXM Series 1200 Watt Marine Subwoofer Amplifier

Continuous RMS Power [watts/channel] @ 14.4V, 2-Ohm mono

24dB/octave, variable 40-160Hz, low pass only;

OutputPower: 10-15W, Frequency Range: 20Hz-20KHz

Scope: Input AC/DC 9-15V Voltage , Current:> 1A (Or >15W),Distortion: <0.1% at 1W

Signal To Noise Ratio: >70dB ,Isolation: >50dB, Net weight: 38g

1-Ohm Minimum Impedance Monoblock Operation | Multi-color RGB LED Illumination Accent Lighting | Solid Color, Flashing, Random, or Slow-Motion Color Change | MOSFET Power Supply with Audiophile Grade IR Transisitors

Direct Short, Thermal and Overload Circuits Protect Amplifier | 200mV-6V Low Level RCA Input and Pre-Amp Output | Variable 12dB Low Pass and Subsonic Crossovers | 12dB Bass Boost Increases Low Octave Harmonics

DataLink for Strapping Two Amps for Double Power | Dash Mount Gain Control Module Included | RMS Power Rating: 800W x 1 at 4-Ohm | 1,400W x 1 at 2-Ohm | 2,500W x 1 at 1-Ohm | 3,000W x 1 at .5-Ohm | 6,000W Max Power

This audio amplifier module is a mono audio amplifier based on the LM386 chip,which is useful for DIY many HAM radio experiments.It is a very cost effective method of small signal amplification.Very convenient instead of using separate components.Handy!

Great small low frequency audio power amplifier to be used for driving small speakers or to build an RC sound module with an arduino. It could be hooked up to headphones directly too

This tiny Op Amp module is good and delivers clear crisp sound.Easy to adjust volume with variable resistor.A convenient screw terminal allows the user to connect a suitable loudspeaker without any soldering.It works with RC truck sound system or an RC boat project

Hifonics ZG-1800.1D Class D Amplifier + Gravity Magnet Phone Holder Bundle

Power Rating: 4 Ohms: 450 Watts x 1 2 Ohms: 900 Watts x 1 1 Ohms: 1800 Watts x 1

Tone Control/Parametric EQ: Built-in bass control | PWM MOSFET Power Supply

Power Handling: 1200W @ 1-Ohm, 1000W @ 2-Ohm, 650W @ 4-Ohm; includes power and protection LED

Remote sub level; bridgeable in/out that allows you to link two amplifiers together

Gain control with 0-12db bass Boost

【Multi-Room Flexibility and Plenty of Power 】True multi-room workhorse that performs well with in-ceiling, indoor or outdoor speakers, the MZ-series amplifiers rated at 50 watts per channel into 8 ohms and 80 watts per channel into 4 ohms. With the Stereo/Bridge switch in the Bridge mode, each zone of channels are combined for a higher powered mono output of 160 watts into 8 ohms when needed.

【 Versatile Easy Connection to Any System】The MZ-1650S can share the same music from one audio source via RCA or S/PDIF as the Global Bus Input, or you can connect up to four external audio sources like a CD player, Alexa Echo, networked music streamer via RCA Line Input to play a different one in each listening room. Each zone of MZ-series amplifier has individual volume adjustment for the left and right channels, giving you precise control over your system

【Work of Art Hi-End Design】Consisting of interlocking blocks of flawless acrylic, deeply brushed and anodized black aluminum with bright Blue LED power switch and zone status indicators brings this amplifier into the beautifully styled, elegant and impressively solid feel.

Onboard chip LM386 Audio Amplifier Module. A circuit design with the advantages of a 20 multiplier. Chip: LM386 power amplifier for Arduino EK1236. PCB Board Size: 1.61 x 0.55inch(L*W), Material: Electric Part.

Car speaker wire clamp. Few peripheral devices; Low distortion; This plate is 200 times the default gain; Onboard horn socket;

Vehicle-mounted 10K variable resistance, adjustable volume. Components and total are widely used tape recorders and radios being.

2-OHM Stereo/4-OHM Mono (StereoChannels) + 2-OHM Mono stable

Variable HP/lp Crossover

Variable gain control

High power 2-way plate amp with DSP for creating active speaker systems

Customizable crossover frequencies, parametric EQ's, limiter, and delay

Simple user interface allows easy DSP adjustment (Windows compatible)