Best Through Hole Prototyping Boards in 2026

★32 pieces double sided PCB prototype boards well packed in a plastic tray which is very easy to store and take out

★5 different size boards to meet your demands when designing your own Arduino kits, electronic experiments and DIY projects

★4 mounting holes at the corners of the board are very convenient for installing them together.

Useful in transferring breadboarded prototypes to reliable and permanent circuits

Popular breadboard alignment for versatile prototyping purposes

Adaptable with a variety of MCU boards. Compatible with Arduino Nano, ESP8266, NodeMCU, etc.

100 % SATISFACTION GUARANTED  ★  Excellent quality and an empty canvas for electrical enthusiasts! An easy soldering; 0.1" hole spacing for DIP integrated circuits and headers.

THIS IS NOT YOUR NORMAL PERF BOARD!  ★  This board is much higher quality with plated-through-holes and annular rings that will not lift off the PCB under normal soldering conditions

MUTI-PURPOSE ★ General purpose prototyping circuit board for analog and digital use; With pre-tinned plated holes; Double sided board with plated-thru holes allows components to be easily soldered to either side of the board

These double side (DS) pcbs with plated through holes design, Each hole on the same side are electrically isolated (NOT a stripboard or sigle side) solderable, You can solder to bridging holes together or use 22-29awg jumper wires for connection. Isolate points bare perfboard.

Lettering on both side of the PC board makes it easier for prototyping projects, Cuttable fiber glass and FR-4 flame resistant good for soldering,Muti Pins, easy to cut and solder with appropriate tools. Flux for easy soldering and extended serving life of printed blank perforated board. Pre-tined plating thru holes

Kits : 20pcs set ( 5pcs 4x6 / 5pcs 3x7 / 5pcs 5x7 / 5pcs 2x8 ) 2*8 3*7 4*6 5*7 CM protoboard | Hole-diameter: 1 mm / 0.04 inches | Hole-pitch point: 2.54mm / 0.1 inches | Conner Mounting-Hole: 2 mm / 0.08 inch | Thickness: 1.6mm / 0.06 inch 5pcs 4 X 6CM double-sided PCB board with 280 holes 5pcs 3 X 7CM double-sided PCB board with 240 holes 5pcs 5 X 7CM double-sided PCB board with 432 holes 5pcs 2 X 8CM double-sided PCB board with 168 holes

Brand new design of the breadboard which have doubled the tie-point from the last version of the breadboard. With the additional ground rail running through the center of both regions was designed specially for integrated circuit and chip testing. The hole in lengthways on two sides was used providing power for the components on the breadboard.

Used among electronic experiments and point-to-point DIY soldering projects, can be expandable with pin header and female header, designing your own Arduino kits. The Breadboard Kit is convenient for the prototypes and circuit design experiment and other DIY projects. Perfect for Arduino, Raspberry Pi, and other programming boards.

Standard IC spacing 2.54MM hole plated through among the pad, Components and kits can be mounted variously on your will. Perfectly working with 3mm&5mm LED Diode kit, Electrolytic Capacitor kit, Monolithic Ceramic Capacitor kit, Resistor kit, etc.

LMV324. This board is compatible with Arduino products as well as other products.

Board has Mic and pre-amp, peak detector, Buffer amplifier and schmitt trigger

The Sound Detector is a small board that combines a microphone and some processing circuitry.

The features of this board is that you don't have to insert the pins of components and kits in the group of holes. Components and kits can be mounted variously on your will.

Used for electronic experiments and point-to-point DIY soldering projects, can be expandable with pin header and female header, designing your own Arduino kits. The Breadboard Kit is convenient for the prototypes and circuit design experiment and other DIY projects. Perfect for Arduino, Raspberry Pi, and other programming boards.

Standard IC spacing 2.54MM hole plated through among the pad can be perfectly working with 3mm&5mm LED Diode kit, Electrolytic Capacitor kit, Monolithic Ceramic Capacitor kit, Resistor kit, etc.

This is a breadboard-style quality prototyping board for through-hole components. Each board measure only 1" by 1" with a 0.1” grid spacing.

Dimensions: 25.4mm x 25.4mm / 1.0” x 1.0”

Number of plated through holes: 81

Standard 0.1" pitch hole pattern for quick and easy circuit board prototyping with many standard electronic components. Works great with Arduino and other electronic starter kits.

.040" Diameter fully plated through holes are used across the perf boards. This type of PCB board allows for high strength solder joints that electrically connect both sides of the circuit board.

0.125" Mounting holes are located in each of the four corners of the prototyping board. These holes allow for easy mounting of the PCB within any project.

This glass fiber PCB double-sided board is an electronic board arranged according to the standard IC spacing (2.54mm). Suitable for point-to-point DIY soldering, electronic projects, circuit design/testing, computer boards, and teaching circuits. Specially designed for beginners to test and learn.

Material: Glass Fiber (FR-4), with Pre-tinned Hole. Thickness: approx. 1.6mm, Hole Pitch: approx. 2.54mm, Hole Diameter: approx. 1 mm

Made of FR-4 glass fiber, double sided with tinned through holes. The boards are durable and the tinned holes can take heat without lifting off. The green layer on the surface of the board is used to protect the formed circuit diagram.

This glass fiber PCB double-sided board is an electronic board arranged according to the standard IC spacing (2.54mm). Suitable for point-to-point DIY soldering, electronic projects, circuit design/testing, computer boards, and teaching circuits. Specially designed for beginners to test and learn.

The prototyping boards we provide here are in the size of: Dimension: 20mm x 80mm / 0.79 x 3.15 inch (W*L); Thickness: 1.6mm / 0.06 inch; Tinned Hole Diameter: 1mm / 0.04 inch; Tinned Hole Pitch: 2.54mm / 0.1 inch

Made of FR-4 glass fiber, double sided with tinned through holes. The boards are durable and the tinned holes can take heat without lifting off. The green layer on the surface of the board is used to protect the formed circuit diagram.

This glass fiber PCB double-sided board is an electronic board arranged according to the standard IC spacing (2.54mm). Suitable for point-to-point DIY soldering, electronic projects, circuit design/testing, computer boards, and teaching circuits. Specially designed for beginners to test and learn.

The prototyping boards we provide here are in the size of: Dimension: 50mm x 70mm / 1.97 x 2.76 inch (W*L); Thickness: 1.6mm / 0.06 inch; Tinned Hole Diameter: 1mm / 0.04 inch; Tinned Hole Pitch: 2.54mm / 0.1 inch

Made of FR-4 glass fiber, double sided with tinned through holes. The boards are durable and the tinned holes can take heat without lifting off. The green layer on the surface of the board is used to protect the formed circuit diagram.

9x15CM Double Side Prototype Board Perforated Through Hole - 1.27mm Pitch

These PCB boards are great for assembly of a point to point style electronics board. Suitable for countless small electronics projects such as building a robot. If you are working with hobby electronics and want a more permanent circuit solution but don't want to design your own PCB, these are great for you!

The prototyping boards we provide here are in the size of: Dimension: 60mm x 80mm / 2.36 x 3.15 inch (W*L); Thickness: 1.6mm / 0.06 inch; Tinned Hole Diameter: 1mm / 0.04 inch; Tinned Hole Pitch: 2.54mm / 0.1 inch

They are made of FR-4 glass fiber, double sided with tinned through holes. This is a fast easy way to build small projects, the boards are durable and the tinned holes can take heat without lifting off.

These PCB boards are great for assembly of a point to point style electronics board. Suitable for countless small electronics projects such as building a robot. If you are working with hobby electronics and want a more permanent circuit solution but don't want to design your own PCB, these are great for you!

The prototyping boards we provide here are in the size of: Dimension: 130mm x 250mm / 5.12 x 9.84 inch (W*L); Thickness: 1.6mm / 0.06 inch; Tinned Hole Diameter: 1mm / 0.04 inch; Tinned Hole Pitch: 2.54mm / 0.1 inch

They are made of FR-4 glass fiber, double sided with tinned through holes. This is a fast easy way to build small projects, the boards are durable and the tinned holes can take heat without lifting off.

This glass fiber PCB double-sided board is an electronic board arranged according to the standard IC spacing (2.54mm). Suitable for point-to-point DIY soldering, electronic projects, circuit design/testing, computer boards, and teaching circuits. Specially designed for beginners to test and learn.

The prototyping boards we provide here are in the size of: Dimension: 80mm x 120mm / 3.15 x 4.72 inch (W*L); Thickness: 1.6mm / 0.06 inch; Tinned Hole Diameter: 1mm / 0.04 inch; Tinned Hole Pitch: 2.54mm / 0.1 inch

Made of FR-4 glass fiber, double sided with tinned through holes. The boards are durable and the tinned holes can take heat without lifting off. The green layer on the surface of the board is used to protect the formed circuit diagram.

This glass fiber PCB double-sided board is an electronic board arranged according to the standard IC spacing (2.54mm). Suitable for point-to-point DIY soldering, electronic projects, circuit design/testing, computer boards, and teaching circuits. Specially designed for beginners to test and learn.

Material: Glass Fiber (FR-4), with Pre-tinned Hole. Thickness: approx. 1.6mm, Hole Pitch: approx. 2.54mm, Hole Diameter: approx. 1 mm

Made of FR-4 glass fiber, double sided with tinned through holes. The boards are durable and the tinned holes can take heat without lifting off. The green layer on the surface of the board is used to protect the formed circuit diagram.

5x5CM Single Side Prototype Board Perforated Through Hole 2.54mm - Pack of 5

Standard 0.1" pitch hole pattern, and convenient electrical connections for quick and easy circuit board prototyping with many standard electronic components. Works great with Arduino and other electronic starter kits.

.040" Diameter fully plated through holes are used across the perf boards. This type of PCB board allows for high strength solder joints that electrically connect both sides of the circuit board.

0.125" Mounting holes are located in each of the four corners of the prototyping board. These holes allow for easy mounting of the PCB within any project.

These PCB boards are great for assembly of a point to point style electronics board. Suitable for countless small electronics projects such as building a robot. If you are working with hobby electronics and want a more permanent circuit solution but don't want to design your own PCB, these are great for you!

The prototyping boards we provide here are in the size of: Dimension: 20mm x 80mm / 0.79 x 3.15 inch (W*L); Thickness: 1.6mm / 0.06 inch; Tinned Hole Diameter: 1mm / 0.04 inch; Tinned Hole Pitch: 2.54mm / 0.1 inch

They are made of FR-4 glass fiber, double sided with tinned through holes. This is a fast easy way to build small projects, the boards are durable and the tinned holes can take heat without lifting off.