Best Treedix in 2026

Brand new design of the breadboard which have doubled the tie-point from the last version of the breadboard. With the additional ground rail running through the center of both regions was designed specially for integrated circuit and chip testing. The hole in lengthways on two sides was used providing power for the components on the breadboard.

Used among electronic experiments and point-to-point DIY soldering projects, can be expandable with pin header and female header, designing your own Arduino kits. The Breadboard Kit is convenient for the prototypes and circuit design experiment and other DIY projects. Perfect for Arduino, Raspberry Pi, and other programming boards.

Standard IC spacing 2.54MM hole plated through among the pad, Components and kits can be mounted variously on your will. Perfectly working with 3mm&5mm LED Diode kit, Electrolytic Capacitor kit, Monolithic Ceramic Capacitor kit, Resistor kit, etc.

Upgraded version from MG995, control angle upgraded from 180° to 360°, have corresponding increase in speed, tension and accuracy.

Compatible with most standard receiver connector: Futaba, Hitec, Sanwa, GWS, etc.

360-degree servo is equivalent to a stepless variable speed motor, which can control the speed and direction.Stable and shock proof, metal gear

The features of this board is that you don't have to insert the pins of components and kits in the group of holes. Components and kits can be mounted variously on your will.

Used for electronic experiments and point-to-point DIY soldering projects, can be expandable with pin header and female header, designing your own Arduino kits. The Breadboard Kit is convenient for the prototypes and circuit design experiment and other DIY projects. Perfect for Arduino, Raspberry Pi, and other programming boards.

Standard IC spacing 2.54MM hole plated through among the pad can be perfectly working with 3mm&5mm LED Diode kit, Electrolytic Capacitor kit, Monolithic Ceramic Capacitor kit, Resistor kit, etc.

Polysilicon solar panel is one kind of solar panel but in different package. Through cutting solar cells into small pieces to meet different required voltage and current, then package.

Using epoxy resin glue to cover the solar cell and with PCB(Printed Circuit Board) attached, have the feature of resist compression, corrosion resisting, crystal-clear appearance, low cost, etc. Encapsulated in waterproof resin so it should not be affected by rain or snow.

Solar panels are devices that absorb sunlight and convert solar radiation directly or indirectly into electricity through photoelectric or photochemical effects, which is perfect devices for science project.

4-bit integrated digital tube, built-in driver, digital clock dedicated digital tube, the display is more intuitive.

Low solder joint density and high welding success rate.

Photoresistor: automatic brightness adjustment; thermistor: sensing ambient temperature; passive buzzer: for music playback.

Features SSD1306 driver chip, which is a single-chip CMOS OLED driver with controller for organic/polymer light emitting diode dot-matrix graphic display system. This IC is designed for Common Cathode type OLED panel.

The 0.91 inch OLED display has the resolution of 128 x 32 pixels. Black background with white or blue text clearly shown on the display.

The OLED panel compared with LCD panel supports self-illumination in every dots and no need for backlight; Can display chinese characters, ASCII, patterns, etc.; And features lower consumption.

Automatic measurement of NPN and PNP transistors, N-channel and P-channel field effect transistors, diodes (including dual diodes), small resistance (including potentiometers), inductance, capacitance, thyristors, batteries (0.1-45V) and other devices.

It can detect infrared wave forms and detect zener diode (0.01-30V), and has the automatic calibration function.

One button operation, automatically detect and shutdown, and you can press the multi-functional button to shut down the detector manually.

MG90S micro servo motor is the upgraded version form SG90 servo motor.

Structural material: Metal copper teeth, hollow cup motor, double ball bearing. Metal Gear with less noise.

Operating Speed（At no load）: 0.12±0.01 seconds / 60 degrees (4.8V); 0.11±0.01 seconds / 60 degrees (6.0V)

【GPIO 1 to 2】: This expansion board can expand one GPIO pin of the development board into two, which is convenient for users to reuse pins in large smart home projects.

【2 connection Methods】: two connection methods: pin connector and screw terminal.

【Good quality】 The product structure is solid, the holes of the breakthrough plate are gold-plated, and the circuit is stable and reliable, without poor circuit contact and unstable signal transmission.

This is made of 316L stainless steel, which has good conductivity, high strength, stable electrical resistivity.

It has an extremely low electrical resistivity, making it suitable for driving LED and other operations.

It exhibits excellent thermal conductivity and can withstand high temperatures.

【Stable performance】 The probe adopts DS18B20 sensor chip, and the collected temperature signal can be directly converted into digital signal for equipment processing

【Good sealing performance】: Sealant with high thermal conductivity is used to encapsulate, ensuring the high sensitivity of the temperature sensor. The cable has strong anti-interference, and is suitable for on-site temperature measurement in harsh environments. (Lead can only withstand a temperature of about 85 ℃. Please pay attention when using)

【DS18B20 temperature sensor]】: The total length of this digital temperature thermal cable is 5m/197 inches, the stainless steel shell is 6 x 50 mm, and the length is long enough for you to use

Digital output of 6-axis or 9-axis rotation matrix, quaternion, and Euler angle forma fusion algorithm data.

3-axis angular velocity sensor (gyroscope) with 131 LSBs/°/sec sensitivity and full frame sensing range of ±250, ±500, ±1000 and ±2000°/sec.

Programmable 3-axis accelerometer with ±2g, ±4g, ±8g and ±16g program control range.

★32 pieces double sided PCB prototype boards well packed in a plastic tray which is very easy to store and take out

★5 different size boards to meet your demands when designing your own Arduino kits, electronic experiments and DIY projects

★4 mounting holes at the corners of the board are very convenient for installing them together.

400 point and 830 point breadboards are available to meet your various experimental needs.

White ABS Plastic Body with Black Printed Legend. Color Legend on Distribution Strips.

With Self-Adhesive Tape on the Back, Easy to Stick on the Arduino Prototype Shield.

Useful in transferring breadboarded prototypes to reliable and permanent circuits

Popular breadboard alignment for versatile prototyping purposes

Adaptable with a variety of MCU boards. Compatible with Arduino Nano, ESP8266, NodeMCU, etc.

This board is especially useful for preserving a prototype or experiment you just created on a solderless breadboard by soldering all the pieces in place

Breadboard PCB for any type Raspberry Pi GPIO

Gold plated finish prevents oxidation, High quality Gold finish for easy soldering

This product contains five different sizes of circuit boards£¬2*8CM,3*7CM,4*6CM,5*7CM,6*8CM,You also can cut these pc boards into any shape any size, it can meet all your needs.

The boards are all basic green body with soldered holes. Good plating around the holes and a nice variety of sizes for the price.

Package comes with totally 50 pcs prototype circuit blank breadboards that is enough for various electronic and soldering project.

100 % SATISFACTION GUARANTED  ★  Excellent quality and an empty canvas for electrical enthusiasts! An easy soldering; 0.1" hole spacing for DIP integrated circuits and headers.

THIS IS NOT YOUR NORMAL PERF BOARD!  ★  This board is much higher quality with plated-through-holes and annular rings that will not lift off the PCB under normal soldering conditions

MUTI-PURPOSE ★ General purpose prototyping circuit board for analog and digital use; With pre-tinned plated holes; Double sided board with plated-thru holes allows components to be easily soldered to either side of the board

Useful in transferring prototypes to reliable and permanent circuits

Snaps Into 4 small boards for versatile prototyping purposes

Adaptable with a variety of MCU boards. Compatible with Arduino Nano, ESP8266, NodeMCU, etc.

PCB Board: 30 pieces double sided PCB prototype boards in 4 different sizes, 10 pieces 2*8cm, 10 pieces 3*7cm, 5 pieces 4*6cm and 5 pieces 5*7cm PCB boards

Header Connector: 10 pieces 40 pin male header, 10 pieces 40 pin pitch right angle male headers, 10 pieces 40 pin female header; pitch: 2.54mm, single row and straight connector

Screw Terminal Block: 5 pieces 5.08-301-2P and 5 pieces 5.08-301-3P ; pitch: 5.08mm, rated voltage: 300V, rated current: 16A

These double side (DS) pcbs with plated through holes design, Each hole on the same side are electrically isolated (NOT a stripboard or sigle side) solderable, You can solder to bridging holes together or use 22-29awg jumper wires for connection. Isolate points bare perfboard.

Lettering on both side of the PC board makes it easier for prototyping projects, Cuttable fiber glass and FR-4 flame resistant good for soldering,Muti Pins, easy to cut and solder with appropriate tools. Flux for easy soldering and extended serving life of printed blank perforated board. Pre-tined plating thru holes

Kits : 20pcs set ( 5pcs 4x6 / 5pcs 3x7 / 5pcs 5x7 / 5pcs 2x8 ) 2*8 3*7 4*6 5*7 CM protoboard | Hole-diameter: 1 mm / 0.04 inches | Hole-pitch point: 2.54mm / 0.1 inches | Conner Mounting-Hole: 2 mm / 0.08 inch | Thickness: 1.6mm / 0.06 inch 5pcs 4 X 6CM double-sided PCB board with 280 holes 5pcs 3 X 7CM double-sided PCB board with 240 holes 5pcs 5 X 7CM double-sided PCB board with 432 holes 5pcs 2 X 8CM double-sided PCB board with 168 holes

The Package comes with 2 pcs double sided pcb prototype board, the proto boards are in the color of Green.

The size of printed circuit board : 9cm X 15cm(3.543" X 5.906"); The weight of one piece universal printed circuit board: 39.0g/1.376oz

The pcb board is double sided, with the plated holes are pre-tinned, the hole diameter of the prototype circuit board is about: 1 mm/0.039", The hole number of printed circuit universal breadboard is: 1836

Selection of Multi-Sized Proto Boards - 31 pieces double-sided prototype boards of 5 different size to meet your demands when designing your own Arduino kits, electronic experiments and DIY projects. （10 pieces 2*8cm, 10 pieces 3*7cm, 5 pieces 4*6cm, 5 pieces 5*7cm and 1 pieces 7*9cm PCB boards

Header Connector - 10 pieces 40 pin male header, 10 pieces 40 pin pitch right angle male headers, 10 pieces 40 pin female header; pitch: 2.54mm, single row and straight connector

Screw Terminal Block - 5 pieces 5.08-301-2P and 5 pieces 5.08-301-3P ; pitch: 5.08mm, rated voltage: 300V, rated current: 16A.

⭐【6 Different Sizes PCB Boards】Double Sided Prototype PCB Boards--1 × 9*7cm, 2 × 8*6cm, 5 × 8*2cm and 5× 7*5cm, 5 × 7*3cm, 5 × 5*4cm PCB Boards, Different Size to Meet Your Demands When Designing Your Own Electronic Projects, Electronic Experiments and DIY Projects.

⭐【Convenient for Projects】The upgrate 0.8mm solder wires, Semi-solid Flux, and High Temperature Marine Resistant Products, Providing Most Necessary Mounting Tools. It’s convenient to use.

⭐【Header Connector】6 pcs 40 pin Male Header, 4 pcs 40 pin Pitch Right Angle Male Headers, 6 pcs 40 Pin Female Header; Pitch: 2.54mm, Single Row and Straight Connector;

5PCS Solderless Breadboards - 3PCS Full-size and 2 PCS Half-size bread boards to meet your experimental needs.

Solid and Reliable - White ABS Plastic solid body with clear printed labels for rows, columns and buses.

Snugly but Lightly - Snugly enough to hold electronic components in place, but lightly enough to remove them.

Prototype PCB for Arduino UNO R3 Shield Board DIY.

Quantity: a lot of 10 pieces.

PCB Dimension: 68.58mm x 53.34mm / 2.7" x 2.1"

✔️3220 Test Points, 4 Binding Posts, 560 U-shape pure copper jumper wires + 65 Pack 24AWG Breadboard Solid Multi colors pure(100%) Copper Jumper Wires Kit

✔️7 Power Lanes, Tie-point 700; 4 Double Strips, Tie-point 2520;

✔️ABS Plastic housing, metal contact clips; Accept wire with diameter 20-29AWG;Black aluminum plate

This Copper Clad Plated Printed Board is desgined For Etch Etching Project.Single Sided (SS) Blank Copper on the Front, FR4 Bakelite on the Back.10 pcs a Pack.

With Small Size 7x10 cm - 2.7" x 4" (W*L), 1.6mm - 0.062" Thickness, Weight in 15g 0.5oz Each.10 pieces epoxy Brown 4 x 2.7 inch

Packed with Moisture Protecting Bag to Prevent Copper Rust. 10pcs Bare Boards Kits Delivered in their Best Conditon.

This Copper Clad Plated Printed Board is desgined For Etch Etching Project.Single Sided (SS) Blank Copper on the Front, Bakelite on the Back.10 pcs a Pack.

With Small Size 7x10 cm - 2.7" x 4" (W*L), 1.6mm - 0.062" Thickness, Weight in 15g 0.5oz Each.10 pieces epoxy Brown 4 x 2.7 inch

Packed with Moisture Protecting Bag to Prevent Copper Rust. 10pcs Bare Boards Kits Delivered in their Best Conditon.

400 Points Breadboard with 2 Positive & Negative Power Lines on both ends.Perfect for Arduino Shield Prototyping and Testing.

Insertion Wire Size is 21 to 26 AWG, 0.016 to 0.028 inches diameter (0.4 to 0.7mm diameter),works with dupont jumper wires kit.

White ABS body with black printed legend. Color legend on distribution strips.