Best Oono in 2026

16Amp 48V 2x12 position screw terminal block distribution module. Support for multiple module extension connections.

Rated current 16 Amp(total input or output), Maximum voltage 48V

A / B terminal blocks, Pitch 7.5mm/0.295", Wire range 26AWG ~ 12AWG / 2.5mm square. Rated current 16Amp. Strip length 7mm. Screws - M3,steel, Cr3+ Zn plated. Pin header and Cage - Brass.

The item has been soldered and assembled. Support for Raspberry Pi 1 Model B+, Pi 2 Model B, Pi 3 Model B, Pi 3 Model B+, Pi 4 Model B, Pi Zero, Pi Zero-W.

Terminal block pitch 2.54mm/0.1", wire size range 28AWG to 18AWG, strip length 4.5mm, screw M1.6 steel, pin header and cage copper.

FR-4 fiber glass PCB, dual copper layers.

20 Amp 48V 2x10 Position Barrier Terminal Block Distribution Module for AC DC. You can chose input from Barrier terminal block, Banana jack or DC power jack. Support for multiple module extension connections.

Rated current 20 Amp(input from barrier terminal block). Input from banana jack maximum current 6 Amp. Input from DC power jack maximum current 5 Amp. Maximum voltage 48V DC or AC.

Barrier terminal blocks: pitch 7.62mm, screw Metric M3(thread diameter 3mm). Banana jacks: standard 4mm jack. DC power jack: for 5.5mm x 2.1mm plug.

Reversing relay module. Powers any reversing motor equipment, can be used for any application that requires the ability to reverse motion

Support Momentary-action(Self-resetting) switch and Alternate-action (Self-holding) switch. For Self-resetting switch, when the switch is pressed the motor operates, and when the switch is released the motor stops.

Compact plastic case and wires connect for easy mount.

Input control signal: Voltage AC or DC 12V, Current 33mA.

Output switch DPST 1NO 1NC(Double Pole Single Throw, 1x Normally Open and 1x Normally Close ), rated current 8A/250VAC or 8A/30VDC (one switch).

Compact plastic case and wires connects for easy mount. LED indication for relay action.

This is a simple and practical blinking flasher module, the ON and the OFF duration can be adjusted separately. The blinking flasher module is suited for both resistive and slightly inductive loads. This blinking flasher module is ideally suited for driving for example LED lamps, hazard lights, warning signs, safety beacons, DC light bulbs, etc ....

Operating voltage DC 4.5 to 30V. Maximum current: 10 Amp. Maximum load 300 Watts/at DC 30V, 120 Watts/at DC 12V. (NOTE: this product no step-up, step-down or inverter function, only for DC load)

Time-ON 0.01 to 15 seconds and Time-OFF 0.01 to 15 seconds adjustable. The output ON - OFF - ON – OFF… cycle alternates.

Rotary Switch, 4-Position 3-Speed.

Rating: 16A 120VAC,12A 250VAC

Step angle: 30 degree. Knob diameter: 26.6mm.

74HC Series High-speed Si-gate CMOS Logic ICs Assorted Kit.

30 Types, total 30 PCS (each 1 PCS), all DIP package.

Packed in a plastic box.

30Amp 300V 2x12 position screw terminal block distribution module. Support for multiple module extension connections.

A / B position maximum current 30Amp(each position). A 1~12 total maximum current 30Amp(total positions). B 1~12 total maximum current 30Amp(total positions). A 1~12 / B 1~12 position maximum current 10Amp(each position). Maximum voltage 300V.

A / B terminal blocks, Pitch 7.62mm/0.3", Wire range 26AWG ~ 10AWG / 4.0mm square, Rated voltage 300V, rated current 30Amp. Strip length 8mm. Screws - M3,steel, Cr3+ Zn plated. Pin header and Cage - Brass.

This is a multi-purpose semi-enclosed enclosure kit, Supports Raspberry Pi 1 Model A+ / Pi 1 Model B+ / Pi 2 Model B / Pi 3 Model B / Pi 3 Model B+ / Pi 4 Module B / Pi Zero / Pi Zero W, Arduino Uno R2 / Uno R3 / Mega 2560 R2 / Mega 2560 R3 / MKR Series etc, and BeagleBone / BeagleBone Black / BeagleBone AI / BeagleBone Black Wireless / BeagleBone Green / BeagleBone Green Wireless or SanCloud BeagleBone Enhanced.

It can be assembled very flexibly as a semi-closed enclosure, or as a two-layer bracket, or if you buy multiple sets, it can be used as a Raspberry Pi cluster case.

The space between the lower cover and the upper cover is 40mm, support Raspberry Pi direct stack HAT module, or Arduino stack SHIELD module, or Beaglebone stack CAP module. Compared with other enclosures, the project is more practical and flexible.

Working voltage DC 0 to 32V. Maximum total input current 30 Amps. 6 Channels output, each channel maximum output current 3 Amps (Factory-installed fuse value 3 Amps, you can replace the fuse to support up to 10 Amps.)

Input terminals pitch 7.62mm/0.3", maximum current 30 Amps for per position, wire size 26~10 AWG, stripping length 8mm, Metric M3 slotted screw. Support power supply expansion connect to other modules.

Output terminals pitch 5.0mm/0.197", wire size 26~12 AWG, stripping length 7mm, Metric M2.5 slotted screw.

MEGA2560 Screw Terminal Block Breakout Module with Aluminum Enclosure. With the adapter module you can easily extend Arduino MEGA2560 projects to industrial control applications. Applications for Arduino MEGA2560 R2 / R3 ( NOTE: the item not include Arduino MEGA2560).

Terminal block pitch 3.5mm/0.138", wire size range 26AWG to 16AWG, strip length 5mm, screw M2 steel, pin header and cage copper. With power on LED indicating, red reset button on the side, with a ICSP adapter connect header.

Support for Desktop, Panel mount, Wall-mount or DIN rail mount. DIN rail mount supports vertical or horizontal place mounting. Can support width 35mm / 32mm / 15mm rail.

Dimmer Control 10-Lights LED Hub Distribution Module, AC/DC 5 to 24V Input, for HO / N / O Train Model.

10 channels dimming output, each channel can be independently adjusted and controlled. All channel can support direct-connected LEDs, or LEDs with resistors in series. Using linear current control circuit, there is no stroboscopic problem of switching circuit to protect your eyesight.

Support AC or DC power supply input, AC 5-18V or DC 5-24V. Each channel adjustable maximum current output 30mA(DC24V) / 20mA(DC18V) / 12mA(DC12V), minimum current 0mA(LED goes out completely).

Operating voltage: 6 to 20VDC, No-load quiescent current: 2.7mA(at 13.8V).

Input port: maximum input current 40A, with a 40A fuse. Output port: 8 output ports, each port has an independent toggle switch and a power-on LED indicator, each port maximum output current 20A.

Voltage over(15.0V) and under(11.5V) LED indicators, and buzzer audio alarm for over voltage or under voltage. if you do not want to hear the alarm, you can open the aluminum case to remove the CN11 buzzer pin jumper.

Input voltage AC 125/250V 50/60Hz. Maximum total input current 40A(one position terminal block maximum current 20A).

Maximum output current 10A(one channel). Maximum total output current 40A.

10Amp rocker switch thermal circuit breaker overload protectors, you can manually set the switch output state RESET or OFF. The switch has a built-in red indicator light, when the output normal indicator is on, the output disconnect indicator is off.

Input voltage AC 125/250V 50/60Hz. Maximum total input current 10A.

Maximum output current 10A.

10Amp rocker switch thermal circuit breaker overload protectors, you can manually set the switch output state RESET or OFF. The switch has a built-in red indicator light, when the output normal indicator is on, the output disconnect indicator is off.

The module can support Raspberry Pi A+ 3A+ B+ 2B 3B 3B+ 4B (of course, Zero and Zero-W can also be supported, but only two screw holes can be fixed).

Support RPi I/O 26 ports 3.3V to 5V bidirectional logic level conversion(input or output). But not include ID_SC and ID_SD ports(since ID_SC and ID_SD are used to identify HAT modules, these two ports are not connected to the 5V interface).

If you short blue terminal block, Raspberry Pi 5V will connect to external 5V. You can use an external 5V to power the Raspberry Pi, of course, you can also power external devices from the Raspberry Pi. Two LEDs are used to indicate the Raspberry Pi 5V and external 5V.

This is a simple and practical automatic forward reverse relay module, cooperate with two external normally open limit switches to realize cyclically reciprocating motion of DC reversing motor. (This product does not come with limit switches, you must select the appropriate limit switch according to your application requirements.)

Operating voltage: 9 to 18VDC (12V version), 18 to 36VDC (24V version). Maximum motor load current 8 Amp.

The product has a power-off memory function, the next time it is turned on, the motor will move along the state of the last power-off.

Free PDF tutorial(more than 22 lessons) and clear listing in a nice package

The most economical kit based on Arduino platform to starting learning electronics for those beginners who are interested.

Lcd1602 module with pin header (not need to be soldered by yourself)

Blue Sea Systems Fuse Block ST Blade 12 Circuit with Ground and Cover, part number 5026, can be used for 24-hour circuits

Max Amps: 100A per block, 30A per circuit, Max Volts: 32V DC, Mounting :#8 (M4) Screw, Negative bus: #10-32 stud, Positive bus: #10-32 stud, Recommended Stud torque: 24 in-lb, Screw Terminal Torque: 18in-lb, Screw terminal type: #8-32 screws with captive star lock washer

Positive distribution bus with #10-32 stud

★【Clean Installation】- How to clean up your cluttered battery terminals? Our terminal strips greatly simplified and neatened up your install. The pressure washer style terminal accepts a bare wire and the jumpers allow signals or power to be distributed neatly. This way you can easily disconnect a wiring branch without taking down the entire system.

★【Heavy Duty】- Our terminal/barrier strips are well made sturdy and with quality and robust screws. You can crank down on these for a firm bite. These allowed you to connect each power wire very cleanly to each source (ground, battery, and ignition on). Great for compact wiring jobs.

★【Protect Cover】- Our dual row screw terminal strips that also include a clear cover to protect accidental touching of the terminal. It will be more safer when the terminals are protected by snap-in plastic "lids". Be careful when mounting these covers.

【QUICK FIX】 – When the current/voltage exceeds the rated range,the fuse will be automatically blown.It has leds beside each load to indicate if a circuit has shorted or has blown.So you can easily identify it and change it!

【MAKE WIRING CLEAN】– Instead of piling a mess of wires and fuse holders onto your battery posts, WUPP 12 volt fuse block/ground bus kit gives you 6 dedicated fuses and 6 ground locations to keep all of your wires clean, organized, and accessible. Made wiring electronics in your vehicles or boat a breeze!

【UNIVERSAL PROTECTION】– The input rated voltage of the fuse box is 32V,and the input rated current is 100A.Each circuit outputs a maximum current of 30A. All bus bars and fuse pieces are nickel-plated copper, corrosion-resistant and highly conductive.

The MEGA complete starter kit with more than 200pcs components, premium quality and 100% Compatible with Arduino IDE

Free pdf tutorial in the cd (33 lessons)

Lcd1602 module and gy-521 sensor module with pin header ( no need to solder by yourself)

Fourteen connections with 2 x 5/16" stainless steel studs and 12 x #8 stainless steel screws. Comes with 4 x 8AWG 5/16”, 4 x 10AWG 5/16”and 24 x #8 insulated ring terminals

Reinforced Polycarbonate cover attaches with nylon nuts to protect against accidental short circuits

Max voltage:300V AC/ 48V DC. Max continuous amperage: 130A AC/150A DC

★【Clean Installation】- How to clean up your cluttered battery terminals? Our terminal strips greatly simplified and neatened up your install. The pressure washer style terminal accepts a bare wire and the jumpers allow signals or power to be distributed neatly. This way you can easily disconnect a wiring branch without taking down the entire system.

★【Heavy Duty】- Our terminal/barrier strips are well made sturdy and with quality and robust screws. You can crank down on these for a firm bite. These allowed you to connect each power wire very cleanly to each source (ground, battery, and ignition on). Great for compact wiring jobs.

★【Protect Cover】- Our dual row screw terminal strips that also include a clear cover to protect accidental touching of the terminal. It will be more safer when the terminals are protected by snap-in plastic "lids". Be careful when mounting these covers.

★【Clean Installation】- How to clean up your cluttered battery terminals? Our terminal strips greatly simplified and neatened up your install. The pressure washer style terminal accepts a bare wire and the jumpers allow signals or power to be distributed neatly. This way you can easily disconnect a wiring branch without taking down the entire system.

★【Heavy Duty】- Our terminal/barrier block are well made sturdy and with quality and robust screws. You can crank down on these for a firm bite. These allowed you to connect each power wire very cleanly to each source (ground, battery, and ignition on). Great for compact wiring jobs.

★【Protect Cover】- Our dual row screw terminal block that also include a clear cover to protect accidental touching of the terminal. It will be more safer when the terminals are protected by snap-in plastic "lids". Be careful when mounting these covers.

1/4" Stud - 12 Terminal Black Power Distribution Block For a Variety Of wiring Scenarios

Includes 12x nylon 16-14 awg #8 1x nylon 12-10 awg 1/4 1x nylon 8 awg 1/4 1x nylon 6 awg 1/4

12 Stainless Steel #8-32 Terminal Screws and Stainless Stud Will Not Rust Or Corrode In Wet Environments

★【Clean Installation】- How to clean up your cluttered battery terminals? Our terminal strips greatly simplified and neatened up your install. The pressure washer style terminal accepts a bare wire and the jumpers allow signals or power to be distributed neatly. This way you can easily disconnect a wiring branch without taking down the entire system.

★【Heavy Duty】- Our terminal/barrier strips are well made sturdy and with quality and robust screws. You can crank down on these for a firm bite. These allowed you to connect each power wire very cleanly to each source (ground, battery, and ignition on). Great for compact wiring jobs.

★【Protect Cover】- Our dual row screw terminal strips that also include a clear cover to protect accidental touching of the terminal. It will be more safer when the terminals are protected by snap-in plastic "lids". Be careful when mounting these covers.

Five connections red busbar with 5 x 3/8" stainless steel studs. Five connections black busbar with 5 x 5/16" stainless steel studs. Comes with 5 x 8AWG 3/8”, 5 x 8AWG 5/16” ring terminals.

Reinforced Polycarbonate cover attaches with nylon nuts to protect against accidental short circuits.

Max voltage:300V AC/ 48V DC. Max continuous amperage: 130A AC/150A DC.

8 Circuit 20 Amp AC/DC 300V AC/DC Terminal Block

Closed back design completely insulates power from the mounting surface

Each screw pair is one isolated circuit