Best Acdelco Automotive Switches in 2026

HANDS-FREE: Never need to take your hands off the work-piece. When we need to shut the power off right away, it can be very dangerous and troublesome to hunting around for a switch under your router table or table saw. With this safety power switch, you can simply turn off the tools by a knee, a thigh or even a hip without much effort. A lot safer and easier than usual.

EASY TO LOCATE: Large paddle for emergency stop. Engaged with a large green recessed ON button safeguarding against accidental starts, and a large red, easy to see OFF paddle. No more feeling around underneath your table to find your switch. The large sign paddle uses high-hardness materials and is more durable.

SIMPLE WIRING: No need complicated wiring. The switch has two cords. The 1.5 feet long female cord is to accept the power source plug from your router or other power tool, and the 5.5 feet long male cord is to plug into your standard wall outlet. Just plug it in and you are ready to go. Both cords are heavy duty to stand up to everyday exposure in workshops.

GET NEW ONE IF NOT MAN MADE BROKEN IN 3 YEARS SINCE YOU PURCHASE THE SWITCH.

Brand New Silver Stainless Steel High Round Pushbutton Switch; Voltage: 250V, 5A. Hole size required: 0.74''/19mm

19mm Momentary Push Button Switch: Push & Hold, ON; Release, OFF, Contact Configuration: 1NO

Simple Operation:Switch on = Power; Switch off = No power.Rating: 275A DC Continuous (1hr), 455A DC Intermittent (5 min), 1250A DC Cranking (10 sec); Stud Size: 2x3/8" (10mm)

Durable Material: This battery disconnect switch is made of ABS plastic housing, tinned copper studs and nuts.Come with 4 stainless steel mounting screws and caps to help fix the switch tightly. 4 Removable side plates provide access for battery cables

Safety Protection:battery shut off switch can disconnects the battery safely, protect batteries from excessive drain when vehicle or boat is not in use

Multi Functional Switch Panel: Product integrated with dual USB port, digital voltmeter, 12V outlet, waterproof board and 5 on / off rocker switches, this 12V/24V electrical panel can meet your various needs

Safety Protection: Real time LED voltmeter shows the status of the voltage. Pre-wire design with 15A fuse providing you with an overload, over-current and short circuit protection.

Wide Application: This switch is suitable for 12V-24V Systems and widely applicable for most DC 12V-24V cars, UTV/ATV, trucks, trailer, RV, caravan, bus, marine, boat, yacht, airplane, etc. Convenient to install with pre-wired and four assemble screws

Single Light Switch: There are 5 single on-off switches of the 5 Gang switch panel. Each switch controls its own LED device. Great for all types of circuit control

Premium Quality:The pre-wired rocker switch can control any 12V DC devices. Made of high quality ABS and aluminum panel, durable and IP65 waterproof, splash-proof, anti-corrosion.

Easy to Install: The switch panel can be mounted horizontally or vertically, you just have to cut out wherever you wanna place it on your car. Panel comes with Stainless steel mounting screws, Helps to install the switch panel firmly according to your needs.

Feature: The waterproof toggle switch is made of metal and bakelite. The shaft and bracket are both made of Brass Material. Switch with M12X0.75 weatherproof Boot Cap Cover, can effectively protect the switch. Delicate appearance with strong Construction. Look chic and high-end on your equipment.

Function: Waterproof toggle switch with 2 pin SPST design (single pole single throw), easy to turn ON OFF. The rating is 30A 12VDC; 15A 250VAC; 20A 125VAC.

Installation: Mounting hole size is 0.48 inches (12.2MM). Each of the terminals has a machine screw for quick connections, The thickness of Terminals is 0.8mm.

4 Gang rocker switch aluminum panel with DIY stickers and night glow stickers can customize these switches as your demands to remind you while using With pre-wired wiring harness for you to easily install in both 12V and 24V vehicles.

Wide Application:Universal for all cars,RVs,Cans, Motorcycles, buses, boats,trailers,jeeps,UTV etc.

Panel Size:The aluminum panel dimension Length x Width x High(5"x2.75''x2.6'')

【COMPATIABLE】This knife-blade battery disconnect switch is suitable for TOP POST TERMINAL, battery NEGATIVE post only. Maximum Current: 750A, Rated Current: 250A. 6v 12v 24v car truck, bus, RV, Boat, trailer battery

【HIGH QUALITY & HEAVY DUTY 】This top post battery disconnect switch is made of brass material, corrosion resistance, conductive performance is good, durably made for safety use

【EASY TO INSTALL】This battery doctor knife switch for top post batteries can be adjusted into a vertical knife switch through the bottom of the screw, easy to install & simple to use. Switch the knife, then power will cut

4 Positions: ACC / OFF / RUN / (START)

Universal fit for car, truck, tractor, trailer, forklift, and more

Designed with a screw lock-nut for through-panel mounting

Package content: 6 X toggle switch, 6 x Waterproof Cover Special note: this switch is Momentary Switch 2 Terminal Pin ；Product Name: Toggle switch; Country of Manufacture: CHINA;

Material: plastic and metal. Solid connection switch with waterproof rubber cap, more convenient to operate. Delicate appearance with strong Construction. Look chic and high-end on your equipment

Connector type: SPST, 2 terminal pin on/off. Power: 15A 250VAC/20A 125VAC ,2 pole (2 wire contacts to hook to) switch, red positive, the standard "hot" wire, black is negative

Diecast zinc alloy housing, push button momentary type can be used as starter switch or horn switch.

Rated up to 50 Amps at 12 V, mounted to panels' 5/8" hole, up to 3/8" thick.

With sealed rubber cap for water, moisture and dust proof, includes cooper terminal screws.

ON/OFF Toggle Switch: This is an SPST toggle switch, 2 pin switch, 2 position design. When turn the switch ON, it will stay at ON position until manually switch it off.

Rating: 30A 12V DC; 15A 24V DC; 20A 125V AC; 15A 250V AC, heavy duty toggle switch 12v design.

Mounting Hole Size: The mounting hole size of this 12 volt toggle switch is 12mm (0.47 inch).

Working Condition: The working condition for the battery switch is 12V-60V voltage and 0-300A

Applications: The battery disconnect is always used as a key part to cut off the current from the battery when it is not working. The switch can be applied to many marine boats RV ATV vehicles and other 12V-60V battery devices.And the switch have four buttons in total, 1-2-both-off. It will separate the battery easily and will let you control the power more convenient.

Material: The battery switch outer shell is made of ABS panel and bolts are galvanized, which is totally rust and corrosion resistant.

Push Button Switch Dimension: This pushbutton with require 3/4''(19mm) diameter Panel Mounting Hole Size. The 2mm Raised Button for easy operating.

Momentary Push Button Switch rating: 5A 250VAC; 10A 110VAC; 10A 12V DC, with Screw Terminals, easy to contact wires. Durable: More than 50,000 Cycles Long electrical life.

Black Horn Push Button Switch Function: Push ON, Release OFF(Finger loose, OFF) Momentary Version, SPST(Single Pole Single Throw) 2 pin Normal Open.

Includes Red Neoprene Cap for Extra Protection Against Dirt and Moisture

Mounts in a 5/8" Diameter Hole in any Orientation

Rated for 60 Amps at 12 Volts

Multi-function designed: this switch panel is integrated with 3 rocker switches and 4.8A dual USB charger with voltmeter. suitable for most 12v-24v dc cars, utvs,atvs, trucks, trailers, rvs, caravans, buses, marine boats, yachts etc.

Efficient charge: dual USB charger enable you charge two devices simultaneously at full speed with 2.4a in each USB port. with a total power of 4.8A, it works for all usb-powered devices. makes the charger 40% faster than conventional chargers.

Led voltage display: the voltmeter is builted in the center of the usb charger, clearly shows the current readings of working volts, easily notice the voltage condition of the vehicles.

Product Name: Toggle switch; Country of Manufacture: CHINA;Feature: The waterproof toggle switch is made of metal and bakelite.The shaft, bracket and terminal of the switch are made of copper and nickel plating material. The main body of the switch is made of bakelite material.

Type:ON/OFF; Connector type: SPST, 2 terminal pin ; Rated Voltage & Current :15A 250V AC;30A 12VDC；Each terminal will be equipped with a wiring terminal, which makes wiring more convenient.

Mechanical life: more than 50.000 cycles. Electrical life: more than 10, 000 cycles,Total Size(Approx) : 30x15x52mm/ 1.2" x 0.58" x2"(L*W*H)

[High Precision and Long Life]: The exterior is made of stainless steel, and the interior is controlled by high-quality reed switches. The sensor is corrosion-resistant, does not rust, has a long life, stable output signal, and accurate measurement. Suitable for gasoline, diesel, water, methanol, etc.

[Easy to Read]: The fuel level gauge has 8 adjustable backlight colors, IP67 waterproof, stainless steel frame, anti-fog curved glass, easy to read (Empty-1/2-Full).

[Easy Installation]: SAE 5 hole mounting pattern, NBR material gasket, good sealing performance, high oil resistance, with M5 5 screws, 10 quick wiring terminals, easy and quick installation by referring to the wiring diagram.

Great for electronmagnetic Starter, relay, Horn Button Switch, PC Power Switch or any circuit controls on over 500,000 cycles.

Mounting Hole Size: Φ16mm, Switch Rating: 3A/250AC, Switch Combanation: 1NO

Momentary Type: Resetable [Push & Hold ON, Release OFF]

Single ON/OFF Switch: 5 Independent ON/OFF switch, this aluminium panel switches can control 5 devices at the same time. 5 gang 3 pin switch blue illuminated, these switches not be signed and you could assign the switches at your needs. Good for both 12V and 24V vehicle.

Safe and Short Circuit Protection: Built with overload protection, easy replace, protect panel from over-heating, over-current, over charging， overvoltage and short circuit. IP65 waterproof, no need to worry water when in boat or ship, safely protecting with anti-reverse, very convenience for using.

Easy to Install: Installation is easy and can be mounted horizontally or vertically, switch panel comes with 4 pieces stainless steel mounting screws, helps to install the switch panel firmly according to your needs.

Switch Size:70x10mm/2.1"x0.4";Mounting hole: 8mm/0.315''

Switches are widely used in automobile hood, ceiling lamp, chassis lamp and trunk notification.

This switch is instantaneous switch, on/off.

→[Including]: Dual 5V USB power socket charger(2.1A+1A) + Digital Voltmeter + 12V power outlet + 6 on-off 5pin RED LED rocker switch + Waterproof board.It's great for all types of circuit control, charging needs and voltage monitoring.

→[Multiple Protaection]: With output short circuit protection, overload protection, reverse polarity protection, prevent any accident caused by overload situation and temperature range can reach -25 degrees to 80 degrees.

→[Easy to install]: The boat switches come with a pre-wired wiring harness. You can put the item into the switch hole, fix it with screws. And then you can begin to use it. The digital voltage display on the marine rocker switches will make it easier than before to monitor a machine.

Heavy Duty (50 amps) push-button momentary switch that is dust and moisture resistant

12V DC, 50A, SPST (single pole, single throw)

Material: Diecast Aluminum & Plastic. Contacts are pure copper for long life . Screw terminals are brass, nickel plated

Feature: The Safety cover toggle switch is 2 Pin SPST(single pole single throw), designed with rocker style, easy to turn ON OFF. The switch rating is 20A 12V DC; 15A 250VAC; 20A 125VAC Heavy Duty.

Material: The safety cover toggle switch is made of Brass Actuator&threaded shaft and bakelite Housing. It's nice looking and Durable.

Red Aircraft Guard Cover prevents accidental start. The toggle switch can be activated only after you flip the switch guard cover. And the switch get OFF automaticly when you close the cover. That can effectively prevent accidental touch on the switch. Delicate appearance with strong Construction. Look chic and high-end on your equipment.

【Great Compatibility】This dual Marine battery switch is Suitable For Two Batteries, It can stand alone, or be locked together with other switches to isolate and Can be used with 12V up to 60V DC systems to isolate and secure the electrical system,Offering a simple economic way of separating two batteries.

【Heavy Duty】Battery shut off switch comes with 1-2-both-off 4 positions,200 A continuous at DC 12V, 455 A Intermittent at DC 12V, 1250 A momentary at DC 12V,3 mounting screw holes(8mm diameter)for 8-10MM screw connection (not included mounting hardware)

【Easy to install】Refer to wiring diagram for installation,ABS plastic housing, making it ideal for marine applications,rear cover insulates terminals against any short of circuits, equiped with 4 sets of bolts.

Quick & easy installation.Chrome plated metal knob

Inclde 2 PCS

Durable materials protect from breakage and corrosive materials

Battery Holder Type: 9v battery holder with switch, 9v battery holder with on off switch

Battery Holder Voltage Output: 9V, 1 x 9v battery holder= 9 volt battery holder with leads; Battery Holder Switch Function: ON/OFF switch on 9 volt battery case holder

9 Volt Battery Holder Dimensions: (L*W*H)/2.657" x 1.299" x 0.835"/6.75cm x 3.30cm x 2.12cm

The magnetic switch and outlet cover can prevent accidentally turning on the lights, is safe to use for both indoor and outdoor switches.

Using Light Switch Guards to cover the shabbat light switch is a very classic method. This cover is suitable for most swing switches.

The toggle switches can be used as magnetic switches and socket covers, built-in magnet attaches to switch screws.

[Momentary switch] Automatic reset, power on when the button is pressed, and power off when the button is released.

[Easy to install] It is widely used as neon lights, led light switches, car horns, ignition switches, doorbells, home appliances buttons, and automotive technical equipment projects.

[Mounting hole size] Opening size 16mm/0.63inch; Maximum switching capacity: 3A/250VAC; Terminal type: screw; Material: stainless steel, plastic, electrical parts.

Designed to connect and disconnect an DC12V 20A electrical circuit at will,SPST:ON-OFF 2 pole；LED Color：Blue；Type:2 Pins (3 Pins with LED)Color：Blue;The rocker toggle switch panel is made of high quality aluminum panel and ABS material, which is durable and waterproof

When the switch is on, The LED lights will come on；Hole diameter：20mm/0.8"；And it comes with a keyhole slot to prevent unwanted rotation

Coppery pin is connected to the battery negative pole,the next pin is connected to the battery positive pole,the last one is connected to the equipment positive pole;Metal panel size：95x65mm//3.7"x2.5"